HP Moonshot 1500 Chassis User Manual Page 17
- Page / 189
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3 Discovering managed entities using IPMITool
Enter the IPMItool sdr list all command to show all management controller records, whether
you are querying an SDRR from the Virtual Zone MC or you are querying a device SDR for Virtual
Cartridge MC records. For example:
# ipmitool —l lanplus —H iloatx-gem-2c -U admin —P admin123 sdr list all
ZoMC | Static MC @ 20h | ok
254 | Log FRU @FEh f0.60 | ok
IPMB0 Phys Link | 0x00 | ok
ChasMgmtCtlr1 | Static MC @ 44h | ok
PsMgmtCtlr1 | Dynamic MC @ 52h | ok
PsMgmtCtlr2 | Dynamic MC @ 54h | ok
PsMgmtCtlr3 | Dynamic MC @ 56h | ok
PsMgmtCtlr4 | Dynamic MC @ 58h | ok
CaMC | Dynamic MC @ 82h | ok
CaMC | Dynamic MC @ A0h | ok
CaMC | Dynamic MC @ A6h | ok
CaMC | Dynamic MC @ DAh | ok
CaMC | Dynamic MC @ A4h | ok
Querying an SDRR from the Zone Management Controller
• Enter the sdr list all command to show all management controller records.
• Management controller records
Chassis controller – statically assigned, always should be present. Even though always
assigned address 0x44, record should be parsed to learn address and channel number
(IPMB=0).
◦
◦ Power supply controllers --- full complement of records always present. Dynamic indication
in record indicates to application that controller may or may not be present. When not
present, the controller will “nak”. Even though always assigned address 0x52-0x58,
records should be parsed to learn address and channel number (IPMB=0).
◦ Cartridge controllers are dynamically added/deleted to the SDRR upon cartridge
insertion/deletion. Possibility of “nak” condition during deletion transitions. Records
should be parsed to learn addresses and channel number (IPMB=0).
Querying a device SDR for a Cartridge Management Controller
• Management controller records
◦ System node controllers – statically assigned, always should be present. Number of system
node controllers is dependent on cartridge type. Some cartridges may not contain host
systems such as switches. Other cartridges may contain 1 or 4 system nodes. Records
should be parsed for addressing and channel number routing. System nodes routed on
channel 7 (IPMB-L).
You can learn the phsical locations of managed entities by entering the PICMG get address
info command. Use the IPMB address of the cartridge to get the physical address (slot number).
You can also learn the chassis topology through chassis FRU serial number for Zones with the same
chassis.
17
- Abstract 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Overview 7
- Sensor Data Model 7
- Sensor type code 8
- SDR repository 10
- Standardized timers 12
- Special timestamp values 13
- 4 IPMItool 18
- Interfaces 19
- Features 20
- Inventory 22
- Chassis management 22
- Synopsis 22
- Description 23
- 5 Command specification 25
- Global commands 29
- Cold reset command 32
- Warm reset command 33
- Get self test results command 33
- Get ACPI power state command 34
- Clear message flags command 37
- Get message flags command 38
- Get message command 39
- Send message command 42
- ◦ version 5 SHA1 hash 44
- ◦ 0h = ASCII+Latin1 47
- ◦ 1h = UTF-8 47
- ◦ 2h = UNICODE 47
- ◦ All other = Reserved 47
- Close session command 57
- Get session info command 57
- Get AuthCode command 59
- Set channel access command 60
- Get channel access command 62
- Get channel info command 63
- Set user access command 65
- Get user access command 66
- Get user name command 68
- Set user name command 68
- Set user password command 69
- Activate payload command 71
- ◦ [0] — Reserved 73
- ◦ 1b = Test mode enabled 73
- IPMI LAN Device Commands 83
- MC watchdog timer commands 96
- Watchdog timer event logging 97
- Pre-timeout interrupt 98
- Reset watchdog timer command 98
- Set watchdog timer command 98
- Get watchdog timer command 100
- Chassis commands 102
- Get chassis status command 103
- Chassis control command 104
- Chassis identify command 105
- Get POH counter command 111
- Event commands 112
- Get event receiver command 113
- SEL commands 114
- Clear SEL 117
- SEL record type ranges 117
- Get SEL time command 118
- Set SEL time command 118
- SDR record IDs 118
- Get SDR command 121
- Add SDR command 122
- Delete SDR command 123
- Clear SDR repository command 123
- Sensor Device Commands 126
- Get device SDR command 127
- Get sensor thresholds command 128
- Get sensor reading command 129
- DCMI specific commands 130
- ◦ [0] Reserved. Write as 0b 133
- Get DCMI sensor info command 134
- Set asset tag command 135
- PICMG specific commands 137
- Table 113 Site type values 138
- System Interfaces 140
- Network function codes 141
- Completion codes 142
- Channel numbers 145
- Logical channels 145
- Channel Privilege Levels 145
- Users & Password support 146
- IPMI sessions 146
- System interface messaging 147
- Bridging 148
- Bridged Request Example 149
- MC IPMB LUNs 151
- KCS Interface/MC LUNs 153
- LAN Interface 154
- RMCP Message Format 155
- Serial Over LAN (SOL) 156
- 7 Support and other resources 157
- Websites 158
- A Command Assignments 159
- B Verbose output examples 164
- 166 Verbose output examples 166
- 168 Verbose output examples 168
- 170 Verbose output examples 170
- 172 Verbose output examples 172
- At cartridge: 174
- 176 Verbose output examples 176
- 178 Verbose output examples 178
- 180 Verbose output examples 180
- 182 Verbose output examples 182
- 184 Verbose output examples 184
- Glossary 186
- 188 Index 188
Related products and manuals for Chassis components HP Moonshot 1500 Chassis
Chassis components HP 744 User Manual
(154 pages)
(154 pages)
Chassis components HP LP 1000r Service Manual
(100 pages)
(100 pages)
© 2020, manymanuals.com. All rights reserved. | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals