HP Moonshot 1500 Chassis User Manual Page 174
- Page / 189
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chassis Device : No
Bridge : No
IPMB Event Generator : Yes
IPMB Event Receiver : No
FRU Inventory Device : Yes
SEL Device : No
SDR Repository : Yes
Sensor Device : Yes
Device ID : CaMC
Entity ID : 160.97 (PICMG Front Board)
Device Slave Address : DAh
Channel Number : 0h
ACPI System P/S Notif : Not Required
ACPI Device P/S Notif : Not Required
Controller Presence : Dynamic
Logs Init Agent Errors : No
Event Message Gen : Enable
Device Capabilities
Chassis Device : No
Bridge : No
IPMB Event Generator : Yes
IPMB Event Receiver : No
FRU Inventory Device : Yes
SEL Device : No
SDR Repository : Yes
Sensor Device : Yes
Device ID : CaMC
Entity ID : 160.97 (PICMG Front Board)
Device Slave Address : A2h
Channel Number : 0h
ACPI System P/S Notif : Not Required
ACPI Device P/S Notif : Not Required
Controller Presence : Dynamic
Logs Init Agent Errors : No
Event Message Gen : Enable
Device Capabilities
Chassis Device : No
Bridge : No
IPMB Event Generator : Yes
IPMB Event Receiver : No
FRU Inventory Device : Yes
SEL Device : No
SDR Repository : Yes
Sensor Device : Yes
Device ID : CaMC
Entity ID : 160.97 (PICMG Front Board)
Device Slave Address : A4h
Channel Number : 0h
ACPI System P/S Notif : Not Required
ACPI Device P/S Notif : Not Required
Controller Presence : Dynamic
Logs Init Agent Errors : No
Event Message Gen : Enable
Device Capabilities
Chassis Device : No
Bridge : No
IPMB Event Generator : Yes
IPMB Event Receiver : No
FRU Inventory Device : Yes
SEL Device : No
SDR Repository : Yes
Sensor Device : Yes
At cartridge:
root@JSMITH-LX:/# ipmitool -I lanplus -H ILOH101GEMINI -U Administrator -P password -t 0xa4 sdr list all -v
Running Get PICMG Properties my_addr 0x20, transit 0, target 0x20
Discovered PICMG Extension 2.3
Discovered IPMB-0 address 0x20
Discovered Target IPMB-0 address 0xa4
Sensor ID : 01-Front Ambient (0x1)
Entity ID : 64.97 (Air Inlet)
Sensor Type (Threshold) : Temperature (0x01)
Sensor Reading : 21 (+/- 0) degrees C
Status : ok
Positive Hysteresis : Unspecified
Negative Hysteresis : Unspecified
Minimum sensor range : -127.000
Maximum sensor range : Unspecified
Event Message Control : Entire Sensor Only
Readable Thresholds : ucr unr
Settable Thresholds :
Threshold Read Mask : ucr unr
Sensor ID : 02-CPU (0x2)
Entity ID : 65.97 (Processor)
Sensor Type (Threshold) : Temperature (0x01)
Sensor Reading : 40 (+/- 0) degrees C
Status : ok
174 Verbose output examples
- Abstract 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Overview 7
- Sensor Data Model 7
- Sensor type code 8
- SDR repository 10
- Standardized timers 12
- Special timestamp values 13
- 4 IPMItool 18
- Interfaces 19
- Features 20
- Inventory 22
- Chassis management 22
- Synopsis 22
- Description 23
- 5 Command specification 25
- Global commands 29
- Cold reset command 32
- Warm reset command 33
- Get self test results command 33
- Get ACPI power state command 34
- Clear message flags command 37
- Get message flags command 38
- Get message command 39
- Send message command 42
- ◦ version 5 SHA1 hash 44
- ◦ 0h = ASCII+Latin1 47
- ◦ 1h = UTF-8 47
- ◦ 2h = UNICODE 47
- ◦ All other = Reserved 47
- Close session command 57
- Get session info command 57
- Get AuthCode command 59
- Set channel access command 60
- Get channel access command 62
- Get channel info command 63
- Set user access command 65
- Get user access command 66
- Get user name command 68
- Set user name command 68
- Set user password command 69
- Activate payload command 71
- ◦ [0] — Reserved 73
- ◦ 1b = Test mode enabled 73
- IPMI LAN Device Commands 83
- MC watchdog timer commands 96
- Watchdog timer event logging 97
- Pre-timeout interrupt 98
- Reset watchdog timer command 98
- Set watchdog timer command 98
- Get watchdog timer command 100
- Chassis commands 102
- Get chassis status command 103
- Chassis control command 104
- Chassis identify command 105
- Get POH counter command 111
- Event commands 112
- Get event receiver command 113
- SEL commands 114
- Clear SEL 117
- SEL record type ranges 117
- Get SEL time command 118
- Set SEL time command 118
- SDR record IDs 118
- Get SDR command 121
- Add SDR command 122
- Delete SDR command 123
- Clear SDR repository command 123
- Sensor Device Commands 126
- Get device SDR command 127
- Get sensor thresholds command 128
- Get sensor reading command 129
- DCMI specific commands 130
- ◦ [0] Reserved. Write as 0b 133
- Get DCMI sensor info command 134
- Set asset tag command 135
- PICMG specific commands 137
- Table 113 Site type values 138
- System Interfaces 140
- Network function codes 141
- Completion codes 142
- Channel numbers 145
- Logical channels 145
- Channel Privilege Levels 145
- Users & Password support 146
- IPMI sessions 146
- System interface messaging 147
- Bridging 148
- Bridged Request Example 149
- MC IPMB LUNs 151
- KCS Interface/MC LUNs 153
- LAN Interface 154
- RMCP Message Format 155
- Serial Over LAN (SOL) 156
- 7 Support and other resources 157
- Websites 158
- A Command Assignments 159
- B Verbose output examples 164
- 166 Verbose output examples 166
- 168 Verbose output examples 168
- 170 Verbose output examples 170
- 172 Verbose output examples 172
- At cartridge: 174
- 176 Verbose output examples 176
- 178 Verbose output examples 178
- 180 Verbose output examples 180
- 182 Verbose output examples 182
- 184 Verbose output examples 184
- Glossary 186
- 188 Index 188
Related products and manuals for Chassis components HP Moonshot 1500 Chassis
Chassis components HP 744 User Manual
(154 pages)
(154 pages)
Chassis components HP LP 1000r Service Manual
(100 pages)
(100 pages)
© 2020, manymanuals.com. All rights reserved. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals