HP rp2450 Manual Page 175
- Page / 202
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter
I/O Card Cage Removal
247
I/O Card Cage Removal
The I/O Card Cage is located at the rear left side of the rp24xx server. To remove the I/O Card Cage, follow the
steps listed below:
CAUTION Ensure that the system is shut down and power removed from the server before attempting
removal or replacement of a component.
Step 1. On the rear bulkhead, remove cables attached to I/O card slots 2 through 4, located inside the card
cage. Remove the cable attached to I/O card slot 1, located outside the card cage.
Step 2. Within the chassis, remove the I/O card from slot 1 on the right side of the I/O Card Cage, attached
to the I/O Backplane as follows: If the card in slot 1 is a Secure Web Console card, unplug the 5V
power connector from the receptacle on the card.
a. Remove the screw that attaches the I/O card to the rear bulkhead.
NOTE A short-shaft or right-angle Phillips-head screwdriver must be used to remove
the screw due to the short distance between the screw head and the right side of
the chassis.
b. Pull the I/O Card out of its slot on the I/O Backplane and place it on a clean anti-static surface.
Step 3. Loosen the two captive Phillips-head screws located at the front of the Card Cage.
Step 4. Grasp the flat lever handle on the right side of the Card Cage and pull it up and forward to release
the I/O Backplane from the System Board.
Step 5. Grasp the I/O Card Cage, tilt the front up, and pull it up and out of the chassis.
CAUTION Do not scrape the I/O Backplane against the CPU heat sink when you lift the card cage out of
the chassis.
The following photograph shows an empty I/O Card Cage.
The following graphic shows an I/O Card Cage.
- Chapter4 4
- What’s New? 7
- Reference Information 9
- Chapter10 10
- System Overview 11
- A400/A500 Block Diagram 13
- Overview 15
- Product Information 15
- Regulatory Information 16
- Electrical Safety 16
- Cabinet Safety Precautions 17
- Declaration of Conformity 33
- FCC Statement (USA Only) 34
- Canada RFI Statement 34
- European Union RFI Statement 34
- Korean RFI Statement 35
- Taiwan RFI Statement 35
- Acoustics (Germany) 36
- Australian C-Tick Label 36
- Laser Safety 36
- ESD Safety Standards 37
- Acoustic Safety Standards 39
- Altitude Operation Standards 43
- Convenience Wall Outlets 47
- Lightning 47
- Vibration 49
- Flammable Materials 49
- Airborne Contaminants 49
- Electrostatic Discharge 49
- 3 System Site Preparation 51
- Chapter60 52
- Cooling Requirements 53
- Input Power Requirements 55
- HP Cabinet Dimensions 57
- Server Dimensions 59
- Chapter74 66
- Unpack the Server 67
- Attaching the Pedestal Base 68
- Open the Accessory Kit 69
- Third Party Software 69
- Server External Connections 71
- Connect a System Console 72
- Connect Power Cords 72
- Cabinet Identification 73
- Cabinet Loading Requirements 73
- Installing the Server 73
- Installing Bezel End Caps 74
- Table 0-2 78
- Table 0-3 78
- Table 0-4 79
- Table 0-3 (Continued) 79
- Table 0-4 (Continued) 80
- Cabinet Installation 89
- Cabinet Mounted Server Unpack 91
- Stacking Servers 99
- Stacking Servers 100
- Unstacking Servers 101
- 5 Operating Instructions 103
- Chapter112 104
- Configuring the GSP LAN Port 105
- Adding Users 105
- GSP> so 106
- Removing Users 107
- Initial Power-up 109
- Boot To Operating System 111
- System Power Down 113
- Chapter124 116
- Add Memory 117
- New I/O Cards For rp24xx 120
- Add Disks 123
- Tools Required 125
- Cleaning Kit Components 125
- Installing the CPU 128
- Chapter 129
- System Console Configuration 131
- LAN Console 133
- Secure Web Console Features 135
- LAN Connection 138
- L1 Self-Test 138
- L2 LAN Activity 138
- L3 Power 138
- RS 232 Serial Port 139
- 8 Troubleshooting the Server 145
- Chapter154 146
- Accessing Error Chassis Logs 147
- Table 7-1 148
- Table 7-1 (Continued) 149
- Replacement Procedures 151
- Chapter194 152
- Front Bezel Removal 157
- Front Bezel Replacement 159
- Server Cover Removal 161
- Server Cover Replacement 163
- HotPlug Software Procedure 165
- HotPlug Hardware Procedure 168
- I/O Card Cage Removal 175
- I/O Card Cage Replacement 177
- PCI I/O Card Removal 179
- PCI I/O Card Replacement 181
- PCI Backplane Removal 183
- PCI Backplane Replacement 185
- DC-DC Converter Removal 187
- DC-DC Converter Replacement 189
- Memory DIMM Removal 191
- Memory DIMM Replacement 193
- Extend a Server From the Rack 199
Related products and manuals for PC/workstation barebones HP rp2450
(294 pages)
(59 pages)© 2020, manymanuals.com. All rights reserved. | 0.442 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals