HP 72SI User Manual Page 159
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Diagnostics B-11
LS - Image Sensor
W-LS-1 - Image Sensor Is Not Operat-
ing
The image sensor shutter cable is dis-
connected.
Connect the image sensor shutter
cable and restart the printer.
W-LS-2 - Image Sensor Is Not Operat-
ing
The image sensor cable is discon-
nected.
Connect the image sensor cable and
restart the printer.
MD - Media Drive
A-MD-1 - Media Advance Stalled The media drive motor has stalled. Check supply spool for binding, and
motor for failure.
(MS) Media Sensing
A-MS-3 - Media Too Far Left/Right Media is loaded too far to the left or
right.
Reload the media closer to the center
of the platen.
A-MS-4 - Media Out There is no media loaded. Load media.
A-MS-5 - Media Too Narrow Media loaded is not wide enough for
printing.
Load media that is at least 24 inches
wide.
W-MS-1 - Media Low Less than 10 feet (3 meters) of media
remains (roll-fed), or less than 1 foot
(30 cm) of media remains (sheet-
fed).
Monitor printing and reload media to
avoid running out of media during
printing.
W-MS-2 -
Media Non-Standard Width
Media loaded may cause head strike. Continue printing or replace media.
W-MS-4 -
Media Advance Switch Detected
Media Advance Switch on back of
printer was depressed.
Press the Load or Unload button on
the control panel to ensure proper
tensioning of the supply and takeup.
W-MS-6 -
Media Too Wide
Media loaded is too wide to be
printed on.
Replace media. See Appendix A,
Specifications, for supported widths.
(PC) Printing Calibrations
W-PC-2 - Media Replaced -
Recalibrate
Media advance accuracy may need to
be recalibrated.
Run Media Feed Calibration if media
type was changed (page 4-6).
W-PC-3 - Head Height Changed -
Recalibrate
Change in head height has invali-
dated calibration.
Run AutoSet (page 4-20).
W-PC-4 - Jets Not Replaced Not all missing jets could be replaced
in the current print mode.
Prime/clean printheads, or choose a
higher quality print mode (page 3-4).
W-PC-6 - Uncalibrated Pass Mode Print mode selected has media
advance rate different from the cali-
brated advance rate, which may
cause banding.
Run Media Feed Calibration
(page 4-6).
WC-PC-7 - Platen Width Not Known Measurement was reset or not per-
formed.
Restart printer to measure platen
width.
(SM) System
A-SM-1 - Printer Not Personalized Defective electronics assembly. Call Authorized Service Provider for
replacement electronics.
Table B-1. Actions and Warnings
Code, Message Cause What to Do
- User Guide 1
- Legal notices 2
- Regulatory Statements 4
- Telecommunications 5
- Network Statement 5
- TABLE OF CONTENTS 9
- Ink and Media 10
- Calibrating the Printer 11
- Maintaining the Printer 11
- Technical Specifications 12
- Troubleshooting 12
- CHAPTER 1 13
- Operating 14
- Requirements 14
- Important Operating 15
- Safety Warnings 17
- Unpacking and 19
- Assembly 19
- Workflow Overview 20
- 600x300 Printing 21
- Parts Overview 22
- Printheads ◆ Micro-Quad 27
- Calibration ◆ AutoSet 27
- Performance and 29
- Ease-of-Use 29
- 1-18 Special Features 30
- CHAPTER 2 31
- MEDIA WIZARD in the margin 40
- Menu Tree 47
- Printer Settings 48
- Print Menu Tree 48
- CHAPTER 3 49
- Selecting a Print Mode 3-5 53
- 3. Press the 53
- Loading Ink 58
- (Pause) key 60
- (Resume) key 60
- Capping the 61
- Printheads 61
- ! (Proceed) key 63
- Loading Roll-Fed 64
- Support for Large Narrow 65
- Media Rolls 65
- ( (No), go to step 18 70
- ! key to continue 70
- Unloading and 73
- Cutting Roll-Fed 73
- 3-28 Respooling Media 76
- ° corners 77
- 3-30 Loading Rigid Media 78
- Fig. 3-13. Media settings 78
- Document, Application 86
- Loading and Squaring the 88
- Example Document Design 89
- Setting Heater 95
- Temperatures 95
- CHAPTER 4 97
- 4-2 When to Calibrate 98
- Media Feed 4-7 103
- Manual X Head 105
- Registration 105
- HEAD-1 +1 106
- Registration successful 106
- Bidi registration 107
- Head 1: 0 107
- HEAD-1 +2.0 108
- Registration Successful 108
- Print Jet Map? 109
- Report Individual Bad Jets 111
- Clear Individual Bad Jets 112
- View Current Bad Jets 113
- Clear All Bad Jets 113
- ( to skip the Purge-n-Wipe 116
- Straightening the 118
- Media Path 118
- Image Sensor 119
- Calibration 119
- CHAPTER 5 121
- Maintenance Schedule 5-3 123
- Task Description 123
- Clean the Rail and 124
- Bearings 124
- Top of the rail 125
- Side of the rail 125
- (behind the belt) 125
- Cleaning the Encoder 126
- Printhead 128
- Maintenance 128
- Cleaning Clogged 129
- Ink Jets 129
- Carriage 130
- Drip tray 130
- Capping station pad 130
- Capping film 130
- Cleaning the Service 131
- Station Doctor Blade 131
- Set the Printhead and 132
- Camera Height 132
- Setting the Camera 135
- Camera enclosure 136
- Calibrate the Service 137
- Station 137
- Not Aligned 138
- Connector 139
- Extended Power Down 141
- APPENDIX A 143
- Specifications General 144
- Specifications A-3 145
- A-4 Specifications 146
- Performance 147
- Supplies and 148
- Accessories 148
- APPENDIX B 149
- Checklist 150
- B-8 Diagnostics 156
- Diagnostics B-9 157
- B-10 Diagnostics 158
- Diagnostics B-11 159
- B-12 Diagnostics 160
- Diagnostics B-13 161
- E-mail [email protected] 162
Related products and manuals for Label printers HP 72SI
Label printers HP AG-2 User Manual
(15 pages)
(15 pages)
Label printers HP SmartStream Print Controller for HP Designjet T3500 Production eMFP User Manual
(83 pages)
(83 pages)
(51 pages)
Label printers HP AMP 130 Printer User Manual
(134 pages)
(134 pages)
Label printers HP AMP 130 Printer User Manual
(134 pages)
(134 pages)
Label printers HP AMP 130 Printer User Manual
(132 pages)
(132 pages)
Label printers HP AMP 130 Printer User Manual
(132 pages)
(132 pages)
Label printers HP AMP 130 Printer User Manual
(132 pages)
(132 pages)
Label printers HP AMP 130 Printer User Manual
(130 pages)
(130 pages)
© 2020, manymanuals.com. All rights reserved. | 3.392 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals