Hp ProLiant DL320 G5p Server User Manual Page 60
- Page / 106
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuration and utilities 60
functioning properly, the system periodically resets the timer. However, when the operating system fails,
the timer expires and restarts the server.
ASR increases server availability by restarting the server within a specified time after a system hang or
shutdown. At the same time, the HP SIM console notifies you by sending a message to a designated
pager number that ASR has restarted the system. You can disable ASR from the HP SIM console or
through RBSU.
ROMPaq utility
The ROMPaq utility enables you to upgrade the system firmware (BIOS) or Lights-Out 100 firmware. To
upgrade the firmware, insert a ROMPaq diskette into the diskette drive or ROMPaq USB Key into an
available USB port and boot the system.
The ROMPaq utility checks the system and provides a choice (if more than one exists) of available
firmware revisions.
For more information about the ROMPaq utility, see the HP website (http://www.hp.com/go/support
).
Integrated Lights-Out 2 technology
The iLO 2 subsystem is a standard component of selected ProLiant servers that provides server health and
remote server manageability. The iLO 2 subsystem includes an intelligent microprocessor, secure memory,
and a dedicated network interface. This design makes iLO 2 independent of the host server and its
operating system. The iLO 2 subsystem provides remote access to any authorized network client, sends
alerts, and provides other server management functions.
Using iLO 2, you can:
• Remotely power up, power down, or reboot the host server.
• Send alerts from iLO 2 regardless of the state of the host server.
• Access advanced troubleshooting features through the iLO 2 interface.
• Diagnose iLO 2 using HP SIM through a web browser and SNMP alerting.
For more information about iLO 2 features, refer to the iLO 2 documentation on the Documentation CD or
on the HP website (http://www.hp.com/servers/lights-out
).
Erase Utility
CAUTION: Perform a backup before running the System Erase Utility. The utility sets the system
to its original factory state, deletes the current hardware configuration information, including
array setup and disk partitioning, and erases all connected hard drives completely. Refer to the
instructions for using this utility.
Run the Erase Utility if you must erase the system for the following reasons:
• You want to install a new operating system on a server with an existing operating system.
• You encounter an error when completing the steps of a factory-installed operating system installation.
The Erase Utility can be accessed from the Maintenance Utilities menu of the SmartStart CD ("SmartStart
software" on page 56).
- User Guide 1
- Intended audience 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Item Description 8
- Front panel LEDs and buttons 9
- Item Description Status 10
- SATA device numbers 11
- Rear panel components 12
- Rear panel LEDs 13
- System board components 14
- System maintenance switch 15
- System board LEDs 16
- Internal USB connector 18
- Fan locations 19
- Operations 20
- Operations 23 23
- Rack planning resources 24
- Optimum environment 24
- Temperature requirements 25
- Rack warnings 26
- Installing hardware options 27
- Registering the server 29
- Introduction 30
- Memory options 30
- Hard drive options 31
- Hard drive guidelines 32
- Removing a hard drive blank 32
- Removing a hard drive 32
- Installing a hard drive 33
- Expansion board option 42
- PCI-X riser board option 44
- Storage controller option 45
- SAS/SATA controller cable 49
- Cabling 51
- Cabling 52 52
- Cabling 53 53
- Battery cabling for BBWC 54
- Cabling 55 55
- Configuration and utilities 56
- HP ROM-Based Setup Utility 57
- Array Configuration Utility 58
- Management tools 59
- ROMPaq utility 60
- Erase Utility 60
- HP Systems Insight Manager 61
- Management Agents 61
- Diagnostic tools 62
- Keeping the system current 63
- Version control 64
- ProLiant Support Packs 64
- Care Pack 65
- Troubleshooting 66
- Symbols on equipment 67
- Warnings and cautions 67
- Symptom information 69
- Service notifications 69
- Loose connections 69
- Diagnostic steps 70
- General diagnosis flowchart 71
- Item Refer to 72
- Symptoms: 73
- Troubleshooting 75 75
- POST problems flowchart 76
- OS boot problems flowchart 77
- • Redundancy failure 80
- Troubleshooting 81 81
- Battery replacement 82
- Battery replacement 83 83
- FCC rating label 84
- Class A equipment 84
- Class B equipment 84
- Modifications 85
- • EMC Directive 2004/108/EC 86
- Japanese notice 87
- BSMI notice 87
- Korean notice 87
- Laser compliance 88
- Battery replacement notice 88
- Electrostatic discharge 90
- Specifications 91
- Technical support 93
- Technical support 94 94
- Customer Self Repair 95
- Reparo feito pelo cliente 97
- Technical support 98 98
- Technical support 99 99
- Technical support 100 100
- Acronyms and abbreviations 101
- Index 104 104
- Index 105 105
- Index 106 106
Related products and manuals for Computer hardware Hp ProLiant DL320 G5p Server
(43 pages)
(113 pages)
(88 pages)© 2020, manymanuals.com. All rights reserved. | 1.866 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals