HP DL120 - ProLiant - G5 Troubleshooting Guide Page 99
- Page / 201
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Error messages 99
Identify Logical Drive Data did not Match with NVRAM
Description: The identify unit data from the array controller does not match with the information stored in
NVRAM. This can occur if new, previously configured drives have been placed in a system that has also been
previously configured.
Action: Run the server setup utility to configure the controller and NVRAM.
Insufficient adapter resources
Description: The adapter does not have sufficient resources to perform posted-write operations to the array
accelerator board. Drive rebuild may be occurring.
Action: Operate the system without the array accelerator board until the drive rebuild completes.
Inter-Controller Link Connection Could Not Be Established
Description: Unable to communicate over the link connecting the redundant controllers.
Action: Be sure both controllers are using the same hardware and firmware revisions. If one controller failed,
replace it.
Less Than 75% Batteries at Sufficient Voltage
Description: The operation of the array accelerator board has been disabled due to less than 75% of the
battery packs being at the sufficient voltage level.
Action: Replace the array accelerator board if the batteries do not recharge within 36 powered-on hours.
Less Than 75% of Batteries at Sufficient Voltage Battery Pack X Below Reference
Voltage
Description: Battery pack on the array accelerator is below the required voltage levels.
Action: Replace the array accelerator board if the batteries do not recharge within 36 powered-on hours.
Logical Drive X Failed Due to Cache Error
Description: This logical drive failed due to a catastrophic cache error.
Action: Replace the array accelerator board and reconfigure using ACU.
Logical Drive X Status = Failed
Description: This status could be issued for several reasons:
• Logical drive is configured for No Fault Tolerance, and one or more drives failed.
• Mirroring is enabled, and any two mirrored drives failed.
• Data Guarding is enabled, and two or more drives failed.
• Another configured logical drive is in the WRONG DRIVE REPLACED or LOOSE CABLE DETECTED
state.
Action: Check for drive failures, wrong drive replaced, or loose cable messages. If a drive failure occurred,
replace the failed drive or drives, and then restore the data for this logical drive from the tape backup.
- HP Proliant Servers 1
- Troubleshooting Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Contents 7 7
- Introduction 8
- 375445-402 (April 2011) 9
- 375445-401 (January 2011) 9
- Introduction 10 10
- Getting started 11
- Pre-diagnostic steps 12
- Warnings and cautions 13
- Electrostatic discharge 14
- Symptom information 15
- Getting started 16 16
- Getting started 17 17
- Common problem resolution 18
- DIMM handling guidelines 19
- Hard drive guidelines 19
- Hard drive LED combinations 20
- Diagnostic flowcharts 22
- Start diagnosis flowchart 24
- General diagnosis flowchart 24
- Diagnostic flowcharts 25 25
- Power-on problems flowchart 26
- Diagnostic flowcharts 27 27
- Diagnostic flowcharts 28 28
- Diagnostic flowcharts 29 29
- POST problems flowchart 30
- Diagnostic flowcharts 31 31
- • Corrupted OS 32
- Diagnostic flowcharts 33 33
- Diagnostic flowcharts 34 34
- Diagnostic flowcharts 35 35
- Diagnostic flowcharts 36 36
- Hardware problems 37
- UPS problems 38
- General hardware problems 39
- Unknown problem 40
- Third-party device problems 41
- Internal system problems 42
- Diskette drive problems 43
- SD card problems 46
- USB drive key problems 46
- Fan problems 47
- Memory problems 48
- Server is out of memory 49
- Memory count error exists 49
- PPM problems 50
- Processor problems 51
- Tape drive problems 51
- Stuck tape issue 52
- Read/write issue 52
- Backup issue 52
- External device problems 53
- Video colors are wrong 54
- Mouse and keyboard problems 55
- Audio problems 55
- Printer problems 55
- Cable problems 56
- Local I/O cable problems 56
- Modem problems 56
- Network controller problems 58
- Expansion board problems 59
- Software problems 60
- Operating system updates 61
- Software locks up 63
- ROM problems 64
- Boot problems 65
- Software tools and solutions 67
- Using RBSU 68
- Auto-configuration process 68
- Boot options 69
- BIOS Serial Console 69
- Configuring AMP modes 69
- Array Configuration Utility 70
- Management tools 72
- Erase Utility 74
- HP Systems Insight Manager 74
- Redundant ROM support 74
- USB support 74
- Diagnostic tools 75
- Integrated Management Log 76
- Array diagnostic software 76
- Keeping the system current 77
- ProLiant Support Packs 78
- Smart Update Firmware DVD 78
- HP Service Pack for ProLiant 78
- HP Smart Update Manager 79
- Firmware maintenance 80
- Option ROMs 81
- Verifying firmware versions 82
- Updating firmware 82
- • ROMPaq Diskette 84
- • ROMPaq USB Key 84
- Online resources 86
- Management of the server 90
- Error messages 91
- Error messages 92 92
- Error messages 93 93
- Error messages 94 94
- Error messages 95 95
- Error messages 99 99
- Mirror Data Miscompare 101
- Error messages 102 102
- Error messages 104 104
- 3. Restart the system 104
- Error messages 107 107
- Error messages 110 110
- Error messages 111 111
- Error messages 112 112
- Error messages 113 113
- Error messages 114 114
- Error messages 115 115
- Error messages 116 116
- Error messages 117 117
- Error messages 118 118
- 2. Replace the drive 118
- Error messages 119 119
- Error messages 120 120
- Error messages 121 121
- Error messages 122 122
- Fan Solution Not Sufficient 123
- Fatal DMA Error 123
- Fatal Express Port Error 123
- Fatal Front Side Bus Error 123
- Fatal Global Protocol Error 123
- Error messages 124 124
- Error messages 125 125
- Error messages 126 126
- No Floppy Drive Present 127
- No Keyboard Present 127
- • Install a power supply 128
- Error messages 129 129
- Error messages 130 130
- 1. Power down the server 130
- 100 Series 132
- 102-System Board Failure 133
- 104-ASR Timer Failure 134
- 162-System Options Not Set 134
- 163-Time & Date Not Set 134
- 180-Log Reinitialized 134
- 200 Series 135
- Error messages 136 136
- Error messages 137 137
- Error messages 138 138
- 300 Series 139
- 400 Series 140
- 600 Series 140
- 1100 Series 142
- 1600 Series 142
- 1611-Fan Failure Detected 143
- Error messages 145 145
- 1700 Series 146
- Error messages 148 148
- Error messages 149 149
- Error messages 150 150
- Error messages 151 151
- Error messages 152 152
- Error messages 153 153
- Paths 154
- Error messages 155 155
- Error messages 156 156
- Error messages 157 157
- • Reseat the controllers 158
- Error messages 159 159
- Error messages 160 160
- Error messages 161 161
- Error messages 163 163
- 1780-Disk 0 Failure 164
- 1781-Disk 1 Failure 165
- 1782-Disk Controller Failure 165
- • Run ACU 166
- 1791-Disk 1 Error 169
- Error messages 170 170
- Event list error messages 171
- Error messages 172 172
- Error messages 173 173
- Error messages 174 174
- Server blade error codes 175
- Interconnect A Error Code 176
- Interconnect B Error Code 177
- Power supply error codes 178
- Memory-related port 85 codes 181
- Miscellaneous port 85 codes 182
- Message ID: 4137 183
- Message ID: 4140 184
- Message ID: 4141 184
- Message ID: 4169 184
- Message ID: 4190 184
- Contacting HP 185
- Microsoft® operating systems 186
- Linux operating systems 187
- SCO operating systems 188
- IBM OS/2 operating systems 189
- Acronyms and abbreviations 191
- Index 195 195
- Index 196 196
- Index 197 197
- Index 198 198
- Index 199 199
- Index 200 200
- Index 201 201
Related products and manuals for PC/workstation barebones HP DL120 - ProLiant - G5
(34 pages)
(17 pages)
© 2020, manymanuals.com. All rights reserved. | 0.197 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals