HP 132A User Manual Page 50
- Page / 330
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2 Command Summary
HP 53131A/132A Command Summary
2-26 Programming Guide
Table 2-2. HP 53131A/132A SCPI Command Summary (Continued)
Keyword/Syntax Parameter Form Std/
New
Comments
:CALCulate2 (Cont.)
:LIMit (Cont.)
:FCOunt
:LOWer?
:UPPer?
[:TOTal]?
:LOWer
[:DATA]
:STATe
:UPPer
[:DATA]
:PCOunt
[:TOTal]?
<numeric_value> [HZ | S
| DEG]
<Boolean>
<numeric_value> [HZ | S
| DEG]
Std
New
New
New
Std
Std
Std
Std
Std
New
New
Subtree. An abbreviation for Fail COunt.
Query only. Returns the number of limit test
failures at the lower limit.
Query only. Returns the number of limit test
failures at the upper limit.
Query only. Returns the total number of
measurements that failed the limit test.
Subtree.
Sets lower limit used in limit testing.
Sets the limit test enable. Note that this setting
must be enabled for any of the other :CALC2
settings can be used.
Subtree.
Sets upper limit used in limit testing.
Subtree. An abbreviation for Pass COunt.
Query only. Returns the total number of
measurements that passed the limit test.
:CALCulate3
:AVERage
:ALL?
:CLEar
:COUNt
:CURRent?
[:STATe]
:TYPE
:DATA?
:FEED
<numeric_value>
<Boolean>
MAXimum | MINimum |
SDEViation | SCALar or
MEAN
“[:]CALCulate[1] ”
Std
Std
New
Std
Std
New
Std
Std
Std
Std
Subsystem. Performs post-acquisition statistics
computation and data transfer.
Subtree. Collects together the commands
associated with the Statistics capabilities.
Returns all four Statistics results (i.e., mean,
standard deviation, maximum, and minimum).
Event; no query. Clears the statistics results
and statistics count.
Selects number of measurements to combine
for statistics.
Query only. Returns the current number of data
values collected, thus far.
Enables/disables statistics post-processing.
Note that this setting must be enabled for any
of the other :CALC3 settings to be used.
Selects which statistic will be in
:CALC3:DATA?,and on the front-panel display.
Query only. Returns statistic result specified by
:CALC3:AVER:TYPE.
Sets the data flow to be fed into the
CALCulate3 block.
- HP 53131A/132A 225 MHz 1
- Universal Counter 1
- Programming Guide 3
- Contents 5
- Operation 6
- 4 Command Reference 10
- 5 Errors 12
- Before You Start 13
- Introduction 14
- Calibrations 15
- Statistics 16
- HP-IB Commands 16
- Getting Started 18
- How to Use This Guide 18
- Experienced Programmers 19
- Applications 20
- Programming Guide Contents 21
- Assumptions 21
- Related Documentation 22
- 1-12 Programming Guide 24
- Command Summary 25
- Some SCPI Syntax Conventions 27
- Channel 3 is optional 28
- SCPI Command Map 30
- Chapter 2 Command Summary 32
- 2-8 Programming Guide 32
- 2-10 Programming Guide 34
- Programming Guide 2-13 37
- 2-14 Programming Guide 38
- Programming Guide 2-15 39
- 2-16 Programming Guide 40
- (Part 1 of 2) 40
- 2-18 Programming Guide 42
- SCPI Conformance Information 44
- IEEE 488.2 Common Commands 45
- 2-22 Programming Guide 46
- Programming Guide 2-23 47
- Std/New Column 48
- Parameter Form Column 48
- Programming Guide 2-25 49
- 2-26 Programming Guide 50
- Programming Guide 2-27 51
- 2-28 Programming Guide 52
- Programming Guide 2-29 53
- 2-32 Programming Guide 56
- Programming Guide 2-33 57
- 2-34 Programming Guide 58
- Programming Guide 2-35 59
- 2-36 Programming Guide 60
- Programming Guide 2-37 61
- 2-38 Programming Guide 62
- Arming SCPI Command Summary 62
- Programming Guide 2-39 63
- *RST Response 64
- sensitivity 65
- hysteresis 65
- 2-44 Programming Guide 68
- Remote Operation 69
- Configuring the HP-IB 72
- Remote/Local Operation 74
- Common Command Format 75
- SCPI Command and Query Format 75
- Abbreviated Commands 77
- Keyword Separator 77
- Optional Keyword 77
- Parameter Types 79
- Parameter Separator 80
- Query Parameters 80
- Suffixes 80
- Command Terminator 81
- Using Multiple Commands 82
- Response Messages 84
- Response Message Syntax 84
- Response Message Data Types 85
- 3-18 Programming Guide 86
- Status Reporting 87
- 3-20 Programming Guide 88
- Functional Diagram 88
- Status Byte Register 89
- Status Register Group 95
- Condition Register 96
- Transition Filter 96
- Event Register 97
- Event Enable Register 97
- Reporting 106
- HP-IB command—Example 2 107
- Disabled—Example 3 107
- Measuring has Completed— 108
- Example 4 108
- Programming Guide 3-41 109
- Elements of SCPI Commands 109
- 3-42 Programming Guide 110
- Measurements 114
- Using the *OPC? Command 115
- Operations 117
- Writing SCPI Programs 123
- 3-56 Programming Guide 124
- Programming Guide 3-57 125
- Programming Examples 126
- Using QuickBASIC 127
- Using Turbo C 127
- 3-60 Programming Guide 128
- Programming Guide 3-61 129
- 3-62 Programming Guide 130
- Programming Guide 3-63 131
- (HP BASIC) 132
- (HP BASIC) (Continued) 133
- 3-66 Programming Guide 134
- BASIC) (Continued) 135
- (Continued) 138
- Programming Guide 3-73 141
- 3-74 Programming Guide 142
- To Use Macros (HP BASIC) 143
- 3-76 Programming Guide 144
- Programming Guide 3-77 145
- 3-78 Programming Guide 146
- Programming Guide 3-79 147
- 3-80 Programming Guide 148
- (QuickBASIC) 150
- (QuickBASIC) (Continued) 151
- Programming Guide 3-85 153
- 3-86 Programming Guide 154
- Programming Guide 3-87 155
- To Use Macros (QuickBASIC) 156
- Programming Guide 3-89 157
- 3-90 Programming Guide 158
- Programming Guide 3-91 159
- 3-92 Programming Guide 160
- Programming Guide 3-93 161
- C) (Continued) 162
- 3-96 Programming Guide 164
- Programming Guide 3-97 165
- 3-98 Programming Guide 166
- Command Reference 167
- :ABORt Command 170
- :CALCulate Subsystems 171
- Chapter 4 Command Reference 172
- 4-6 Programming Guide 172
- :CALCulate[1] Subsystem 173
- :CALCulate[1]:IMMediate 174
- :CALCulate[1]:MATH Subtree 175
- :CALCulate2 Subsystem 177
- :CALCulate2:LIMit Subtree 178
- Query Response 179
- Comments 179
- :CALCulate2:LIMit:FAIL? 180
- [HZ 182
- [HZ 184
- :CALCulate3 Subsystem 185
- :CALCulate3:AVERage:CLEar 186
- 188
- :CALCulate3:DATA? 188
- :CALCulate3:LFILter Subtree 189
- :CALCulate3:PATH? 191
- :CALibration Subsystem 192
- Front-Panel 193
- :CALibration:SECurity Subtree 194
- :CONFigure Subsystem 196
- Device Clear 197
- :DIAGnostic Subsystem 198
- AUTO ONCE 199
- :DISPlay Subsystem 203
- “[:]CALCulate3” 204
- :FETCh Subsystem 206
- :FORMat Subsystem 207
- Group Execute Trigger 208
- :HCOPy Subsystem 209
- :INITiate Subsystem 210
- :INITiate[:IMMediate] 212
- :INPut[1 214
- :INPut3 Subsystem 216
- :MEASure Subsystem 217
- :FETCh, :MEASure, :READ) 218
- [,<source_list>] 219
- :CONFigure? 220
- 4-64 Programming Guide 230
- Programming Guide 4-69 235
- 4-72 Programming Guide 238
- Using :MEAsure 241
- Using :CONFigure with :READ? 242
- :MEMory Subsystem 245
- [:SENSe] Subsystem 246
- <numeric_value> [V] 248
- <numeric_value> [PCT] 249
- [:SENSe]:EVENt3 Subtree 250
- [:SENSe]:EVENt3:SLOPe? 251
- [:SENSe]:FREQuency Subtree 251
- 252
- 253
- <numeric_value> [S] 253
- <numeric_value> [HZ] 254
- [:SENSe]:PHASe Subtree 257
- [:SENSe]:ROSCillator Subtree 258
- S/N Prefix Below 3646) 261
- (HP 53131A and HP 53132A 261
- With S/N Prefix Below 3646) 261
- Programming Guide 4-99 265
- 269
- [:SENSe]:TOTalize Subtree 270
- EXTernal TIMer 272
- :STATus Subsystem 273
- :STATus:OPERation[:EVENt]? 274
- :STATus:OPERation:NTRansition 275
- :STATus:OPERation:PTRansition 275
- :STATus:PRESet 276
- :STATus:QUEStionable Subtree 276
- :STATus:QUEStionable[:EVENt]? 278
- :SYSTem Subsystem 280
- <numeric_value> 281
- ODD 282
- :SYSTem:ERRor? 282
- :SYSTem:KEY:LOG? 284
- :SYSTem:VERSion? 284
- :TRACe Subsystem 285
- :TRACe[:DATA]? SCALE 286
- :TRIGger Subsystem 287
- (Calibration Query) 288
- (Clear Status Command) 289
- *DDT <arbitrary block> 290
- (Define Macro Command) 291
- *EMC <NRf> 292
- (Enable Macro Command) 292
- (Enable Macro Query) 292
- *ESE <NRf> 293
- (Event Status Register Query) 294
- *GMC? <string> 295
- (Get Macro Contents Query) 295
- (Identification Query) 296
- (Learn Macro Query) 297
- (Operation Complete Command) 298
- (Operation Complete Query) 299
- (Option Identification Query) 300
- (Purge Macro Command) 301
- *RCL <NRf> 302
- (Recall Command) 302
- (Reset Command) 303
- *SAV <NRf> 304
- (Save Command) 304
- *SRE <NRf> 305
- (Status Byte Query) 306
- (Trigger Command) 307
- (Self-Test Query) 308
- (Wait-to-Continue Command) 309
- 4-144 Programming Guide 310
- Displaying Errors 312
- Reading an Error 312
- Error Queue 313
- Error Types 314
- Execution Error 315
- Query Error 316
- Chapter 5 Errors 317
- Programming Guide 5-7 317
- Table 5-2. Errors 317
- 5-8 Programming Guide 318
- Programming Guide 5-9 319
- 5-10 Programming Guide 320
- Programming Guide Index-1 321
- Index-4 Programming Guide 324
- Programming Guide Index-5 325
- Technical Support: 327
Related products and manuals for Measuring, testing & control HP 132A
(112 pages)© 2020, manymanuals.com. All rights reserved. | 1.385 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals