HP 132A User Manual Page 112
- Page / 330
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 Programming Your Universal Counter for Remote Operation
How to Program the Counter to Display Results
3-44 Programming Guide
Commands for Displaying Scaled/Offset Results
The following lines will enable Math (scale/offset). It is assumed that the values
for scale and offset are already set. If not, the default value for scale is 1 and for
offset is 0.
:DISP:MENU OFF
:DISP:TEXT:FEED ‘CALC2’
:CALC2:LIM:DISP NUMBER
:CALC:MATH:STATE ON
:CALC:IMM
Clear any menu items that may be on
display.
Show the non-statistical result.
Use the numeric display mode.
Enable math.
Cause a calculation to be made to update
display.
Note that :CALC2:LIM:DISP NUMBER will only show the raw result if the
command :DISP:TEXT:FEED ‘CALC2’ is also issued. These commands must be
issued in pairs.
Commands for Displaying the Limit Graph
The following lines enable limit testing and show the limit graph.
If the Math is enabled, the scale and offset will be applied to the measurement
result before being tested for the limit graph.
:DISP:MENU OFF
:DISP:TEXT:FEED ‘CALC2’
:CALC2:LIM:STATE ON
:CALC2:LIM:DISP GRAPH
:CALC:IMM
Clear any menu items that may be on
display.
Show the non-statistical result.
Enable limit testing.
Display the limit test result graph.
Cause a calculation to be made to update
display.
Commands for Displaying Statistics Results
The following lines enable Statistics. The default value displayed is Mean.
:DISP:MENU OFF
:DISP:TEXT:FEED ‘CALC3’
:CALC3:AVER ON
Clear any menu items that may be on display.
Show statistical results.
Enable statistics.
- HP 53131A/132A 225 MHz 1
- Universal Counter 1
- Programming Guide 3
- Contents 5
- Operation 6
- 4 Command Reference 10
- 5 Errors 12
- Before You Start 13
- Introduction 14
- Calibrations 15
- Statistics 16
- HP-IB Commands 16
- Getting Started 18
- How to Use This Guide 18
- Experienced Programmers 19
- Applications 20
- Programming Guide Contents 21
- Assumptions 21
- Related Documentation 22
- 1-12 Programming Guide 24
- Command Summary 25
- Some SCPI Syntax Conventions 27
- Channel 3 is optional 28
- SCPI Command Map 30
- Chapter 2 Command Summary 32
- 2-8 Programming Guide 32
- 2-10 Programming Guide 34
- Programming Guide 2-13 37
- 2-14 Programming Guide 38
- Programming Guide 2-15 39
- 2-16 Programming Guide 40
- (Part 1 of 2) 40
- 2-18 Programming Guide 42
- SCPI Conformance Information 44
- IEEE 488.2 Common Commands 45
- 2-22 Programming Guide 46
- Programming Guide 2-23 47
- Std/New Column 48
- Parameter Form Column 48
- Programming Guide 2-25 49
- 2-26 Programming Guide 50
- Programming Guide 2-27 51
- 2-28 Programming Guide 52
- Programming Guide 2-29 53
- 2-32 Programming Guide 56
- Programming Guide 2-33 57
- 2-34 Programming Guide 58
- Programming Guide 2-35 59
- 2-36 Programming Guide 60
- Programming Guide 2-37 61
- 2-38 Programming Guide 62
- Arming SCPI Command Summary 62
- Programming Guide 2-39 63
- *RST Response 64
- sensitivity 65
- hysteresis 65
- 2-44 Programming Guide 68
- Remote Operation 69
- Configuring the HP-IB 72
- Remote/Local Operation 74
- Common Command Format 75
- SCPI Command and Query Format 75
- Abbreviated Commands 77
- Keyword Separator 77
- Optional Keyword 77
- Parameter Types 79
- Parameter Separator 80
- Query Parameters 80
- Suffixes 80
- Command Terminator 81
- Using Multiple Commands 82
- Response Messages 84
- Response Message Syntax 84
- Response Message Data Types 85
- 3-18 Programming Guide 86
- Status Reporting 87
- 3-20 Programming Guide 88
- Functional Diagram 88
- Status Byte Register 89
- Status Register Group 95
- Condition Register 96
- Transition Filter 96
- Event Register 97
- Event Enable Register 97
- Reporting 106
- HP-IB command—Example 2 107
- Disabled—Example 3 107
- Measuring has Completed— 108
- Example 4 108
- Programming Guide 3-41 109
- Elements of SCPI Commands 109
- 3-42 Programming Guide 110
- Measurements 114
- Using the *OPC? Command 115
- Operations 117
- Writing SCPI Programs 123
- 3-56 Programming Guide 124
- Programming Guide 3-57 125
- Programming Examples 126
- Using QuickBASIC 127
- Using Turbo C 127
- 3-60 Programming Guide 128
- Programming Guide 3-61 129
- 3-62 Programming Guide 130
- Programming Guide 3-63 131
- (HP BASIC) 132
- (HP BASIC) (Continued) 133
- 3-66 Programming Guide 134
- BASIC) (Continued) 135
- (Continued) 138
- Programming Guide 3-73 141
- 3-74 Programming Guide 142
- To Use Macros (HP BASIC) 143
- 3-76 Programming Guide 144
- Programming Guide 3-77 145
- 3-78 Programming Guide 146
- Programming Guide 3-79 147
- 3-80 Programming Guide 148
- (QuickBASIC) 150
- (QuickBASIC) (Continued) 151
- Programming Guide 3-85 153
- 3-86 Programming Guide 154
- Programming Guide 3-87 155
- To Use Macros (QuickBASIC) 156
- Programming Guide 3-89 157
- 3-90 Programming Guide 158
- Programming Guide 3-91 159
- 3-92 Programming Guide 160
- Programming Guide 3-93 161
- C) (Continued) 162
- 3-96 Programming Guide 164
- Programming Guide 3-97 165
- 3-98 Programming Guide 166
- Command Reference 167
- :ABORt Command 170
- :CALCulate Subsystems 171
- Chapter 4 Command Reference 172
- 4-6 Programming Guide 172
- :CALCulate[1] Subsystem 173
- :CALCulate[1]:IMMediate 174
- :CALCulate[1]:MATH Subtree 175
- :CALCulate2 Subsystem 177
- :CALCulate2:LIMit Subtree 178
- Query Response 179
- Comments 179
- :CALCulate2:LIMit:FAIL? 180
- [HZ 182
- [HZ 184
- :CALCulate3 Subsystem 185
- :CALCulate3:AVERage:CLEar 186
- 188
- :CALCulate3:DATA? 188
- :CALCulate3:LFILter Subtree 189
- :CALCulate3:PATH? 191
- :CALibration Subsystem 192
- Front-Panel 193
- :CALibration:SECurity Subtree 194
- :CONFigure Subsystem 196
- Device Clear 197
- :DIAGnostic Subsystem 198
- AUTO ONCE 199
- :DISPlay Subsystem 203
- “[:]CALCulate3” 204
- :FETCh Subsystem 206
- :FORMat Subsystem 207
- Group Execute Trigger 208
- :HCOPy Subsystem 209
- :INITiate Subsystem 210
- :INITiate[:IMMediate] 212
- :INPut[1 214
- :INPut3 Subsystem 216
- :MEASure Subsystem 217
- :FETCh, :MEASure, :READ) 218
- [,<source_list>] 219
- :CONFigure? 220
- 4-64 Programming Guide 230
- Programming Guide 4-69 235
- 4-72 Programming Guide 238
- Using :MEAsure 241
- Using :CONFigure with :READ? 242
- :MEMory Subsystem 245
- [:SENSe] Subsystem 246
- <numeric_value> [V] 248
- <numeric_value> [PCT] 249
- [:SENSe]:EVENt3 Subtree 250
- [:SENSe]:EVENt3:SLOPe? 251
- [:SENSe]:FREQuency Subtree 251
- 252
- 253
- <numeric_value> [S] 253
- <numeric_value> [HZ] 254
- [:SENSe]:PHASe Subtree 257
- [:SENSe]:ROSCillator Subtree 258
- S/N Prefix Below 3646) 261
- (HP 53131A and HP 53132A 261
- With S/N Prefix Below 3646) 261
- Programming Guide 4-99 265
- 269
- [:SENSe]:TOTalize Subtree 270
- EXTernal TIMer 272
- :STATus Subsystem 273
- :STATus:OPERation[:EVENt]? 274
- :STATus:OPERation:NTRansition 275
- :STATus:OPERation:PTRansition 275
- :STATus:PRESet 276
- :STATus:QUEStionable Subtree 276
- :STATus:QUEStionable[:EVENt]? 278
- :SYSTem Subsystem 280
- <numeric_value> 281
- ODD 282
- :SYSTem:ERRor? 282
- :SYSTem:KEY:LOG? 284
- :SYSTem:VERSion? 284
- :TRACe Subsystem 285
- :TRACe[:DATA]? SCALE 286
- :TRIGger Subsystem 287
- (Calibration Query) 288
- (Clear Status Command) 289
- *DDT <arbitrary block> 290
- (Define Macro Command) 291
- *EMC <NRf> 292
- (Enable Macro Command) 292
- (Enable Macro Query) 292
- *ESE <NRf> 293
- (Event Status Register Query) 294
- *GMC? <string> 295
- (Get Macro Contents Query) 295
- (Identification Query) 296
- (Learn Macro Query) 297
- (Operation Complete Command) 298
- (Operation Complete Query) 299
- (Option Identification Query) 300
- (Purge Macro Command) 301
- *RCL <NRf> 302
- (Recall Command) 302
- (Reset Command) 303
- *SAV <NRf> 304
- (Save Command) 304
- *SRE <NRf> 305
- (Status Byte Query) 306
- (Trigger Command) 307
- (Self-Test Query) 308
- (Wait-to-Continue Command) 309
- 4-144 Programming Guide 310
- Displaying Errors 312
- Reading an Error 312
- Error Queue 313
- Error Types 314
- Execution Error 315
- Query Error 316
- Chapter 5 Errors 317
- Programming Guide 5-7 317
- Table 5-2. Errors 317
- 5-8 Programming Guide 318
- Programming Guide 5-9 319
- 5-10 Programming Guide 320
- Programming Guide Index-1 321
- Index-4 Programming Guide 324
- Programming Guide Index-5 325
- Technical Support: 327
Related products and manuals for Measuring, testing & control HP 132A
(112 pages)© 2020, manymanuals.com. All rights reserved. | 1.604 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals