Hp ML100 User Manual Page 43
- Page / 111
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Embedded SATA RAID feature
mbedded SATA controller in the system,
0).
Config g
1. ATA RAID functionality in RBSU ("Enabling the SATA RAID feature in RBSU" on page 43).
2. Crea
Enabling the SATA RAID feature in RBSU
HP provides the SATA RAID feature through use of ACU. For the e
this feature enables RAID functionality (RAID 0, RAID 1, or RAID 1
urin the SATA RAID feature
To configure the SATA RAID feature, do the following:
Enable S
te a RAID volume.
CAUTION: Back up any data stored on the hard drives before proceeding. The configuration
process erases all data on the hard drives.
owered, save all data, exit all open applications, and
e RAID option in RBSU is only necessary for installation of the RAID driver.
If this option is not enabled, the OS loads the standard ATA driver from the OS media.
1. Power up the server. If the server is already p
restart.
NOTE: Enabling th
2. During POST, press the F10 key to launch RBSU. If you fail to press F10 before POST, you will need
ges and close RBSU. The server automatically reboots.
Creating a RAID volume
1. ab
2. After AID Configuration Utility.
4.
menu. The system prompts a selection of
to restart the server.
3. In the Advanced menu screen, select Hard Disk Configuration.
4. Set the Configure Controller 1 field to RAID.
5. Press F10, then select Yes to save the chan
6. Create a RAID volume.
En le SATA RAID functionality in RBSU ("Enabling the SATA RAID feature in RBSU" on page 43).
the system reboots, press F8 to activate the R
3. From the Option menu, select Array Configuration Utility.
Verify that two SATA drives are installed.
5. In the Main menu screen, select Create Array from the main
RAID 0, RAID 1, or RAID 10.
6. Select a RAID level.
CAUTION: Back up any data stored on the hard drives before proceeding.
process erases all data on the hard drives.
The configuration
7. Press Esc. The system automatically configures the RAID level, erasing all existing data on the hard
drives. This process can take up to 50 minutes, depending on drive capacity.
8. After configuration is complete, press Esc to exit the utility.
For more information on configuring the SATA RAID feature, see the
HP Embedded SATA RAID Controller
User Guide
on the HP website (http://www.hp.com/support/E_SATA_RAID_C_UG_en).
Software and configuration utilities 43
- User Guide 1
- Intended audience 2
- Contents 3
- Operations 7
- Rack planning resources 9
- Optimum environment 9
- Setup 10 10
- Temperature requirements 11
- Power requirements 11
- Rack warnings 12
- Installing hardware options 12
- Registering the server 13
- Introduction 14
- Processor option 14
- DIMM identification 25
- Memory configurations 25
- Single-rank 24 GB 48 GB 26
- Dual-rank 24 GB 48 GB 26
- Quad-rank 24 GB 48 GB 26
- Installing 28
- Expansion board options 29
- ROM-Based Setup Utility 38
- Array Configuration Utility 39
- Management 40
- Keeping the system current 42
- Embedded SATA RAID feature 43
- USB diskette and CD-R 44
- OM drives 44
- Creating a diskette image 45
- Troubleshooting 47
- Warnings and cautions 48
- Symptom information 49
- Common problem resolution 50
- DIMM handling guidelines 51
- SAS and S TA 51
- Troubleshooting flowcharts 52
- General diagnosis flowchart 53
- Power-on problems flowchart 55
- POST problems flowchart 57
- Item See 58
- OS boot problems flowchart 59
- • Redundancy failure 61
- Hardware problems 62
- Power problems 63
- General hardware problems 64
- Unknown problem 65
- Third-party device problems 65
- Internal system problems 66
- DAT drive problems 67
- Diskette drive problems 68
- Fan problems 69
- Hard drive problems 69
- Data is inaccessible 70
- Memory problems 71
- PPM pro s 72
- Process p 72
- System e 73
- External device problems 73
- Audio problems 74
- Mouse and keyboard problems 75
- Software problems 79
- Operating system updates 80
- Linux operating systems 81
- Firmware maintenance 82
- Drivers 84
- Server in 84
- Microsoft® 85
- operating systems 85
- Battery 87
- Battery 88 88
- FCC rating label 89
- Class A equipment 89
- Class B equipment 89
- Modifications 90
- • EMC Directive 2004/108/EC 91
- Japanese notice 92
- Battery repl 94
- (Geräuschemission) 95
- Electrostatic discharge 96
- Technical support 97
- Technical support 98 98
- Technical support 99 99
- Technical support 100 100
- Reparo feito pelo cliente 101
- Technical support 102 102
- Technical support 103 103
- Technical support 104 104
- Acro abbreviations nyms and 105
- Index 108 108
- Index 109 109
- Index 110 110
- Index 111 111
Related products and manuals for Computers Hp ML100
Computers Hp Compaq User Manual
(22 pages)
(22 pages)
Computers Hp PAVILION DV3 User Manual
(114 pages)
(114 pages)
Computers Hp ProLiant DL140 User Manual
(29 pages)
(29 pages)
Computers Hp BL460C G6 User Manual
(107 pages)
(107 pages)
Computers Hp DL185 User Manual
(103 pages)
(103 pages)
Computers Hp LC 2000 User Manual
(194 pages)
(194 pages)
Computers Hp ProLiant ML115HP User Manual
(26 pages)
(26 pages)
Computers Hp XW6400X User Manual
(90 pages)
(90 pages)
Computers Hp Slimline s3230 User Manual
(2 pages)
(2 pages)
Computers Hp 576X-B User Manual
(1 pages)
(1 pages)
Computers Hp Pavilion 414.uk User Manual
(2 pages)
(2 pages)
Computers Hp QUICKSPECS DL380 User Manual
(56 pages)
(56 pages)
Computers Hp BL2X220C User Manual
(82 pages)
(82 pages)
Computers Hp Vectra VL 5/xxx User Manual
(102 pages)
(102 pages)
Computers Hp BA322 90087 User Manual
(346 pages)
(346 pages)
Computers Hp XW6200 User Manual
(78 pages)
(78 pages)
Computers Hp ProLiant DL785 User Manual
(42 pages)
(42 pages)
Computers Hp LH 3r User Manual
(23 pages)
(23 pages)
© 2020, manymanuals.com. All rights reserved. | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals