Hp XP P9500 Storage User Manual Page 101
- Page / 192
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Corrective actionCurrent status
3. Make sure that all the pairs belonging to the journal in the primary site
are released.
4. Create a Cnt Ac-J delta resync pair that extends from the primary site to
the Cnt Ac-J secondary site.
Primary site: PSUE or PSUS 1. Release the Cnt Ac-J pair from the primary site.
Cnt Ac-J secondary site: HOLD
2. Make sure that all the pairs belonging to the journal in the primary site
are released.
3. Create a Cnt Ac-J delta resync pair that extends from the primary site to
the Cnt Ac-J secondary site.
Change the status of the HLDE pair back to HOLD using pairresync.Primary site: HLDE
Cnt Ac-J secondary site: HOLD
Primary site: SMPL 1. Release the pair in HOLD status from the Cnt Ac-J secondary site.
Cnt Ac-J secondary site: HOLD
2. Create a Cnt Ac-J delta resync pair that extends from the primary site to
the Cnt Ac-J secondary site.
Recovery in a 2DC configuration
Host operations are transferred to the Continuous Access Journal S-VOL in the remote site when a
disaster or failure occurs in the primary site in a 2DC configuration. Failures are corrected at the
primary site, host operations are transferred back, and the 2DC configuration is reestablished.
See “2 Data center configuration” (page 151) for information and illustrations on the configuration
covered in this procedure.
To recover a 2DC configuration failure
1. In the remote site, confirm the consistency of the Cnt Ac-J S-VOL.
2. In the intermediate site, release the Cnt Ac-S pair using the Pairsplit-S command.
3. In the intermediate and remote sites, release the Cnt Ac-J pair using the Pairsplit-S command.
4. Confirm that the Cnt Ac-J S-VOL has changed to SMPL status.
5. Resume host operations to the Cnt Ac-J S-VOL on the remote site.
NOTE: Be aware of the following:
• The 2DC configuration does not allow host operations on the intermediate site.
• If the intermediate site is not connected to a host, use the remote command device for
Cnt Ac-J and Cnt Ac-S pair operations.
6. On the primary site, if Cnt Ac-S pairs exist, release them.
7. On the remote Cnt Ac-J site, create a Cnt Ac-S pair:
• Use the Cnt Ac-J S-VOL on the remote site as the Cnt Ac-S P-VOL. This is the current disaster
recovery production volume.
• Use the primary site volume as the Cnt Ac-S S-VOL
Follow all requirements for creating a Cnt Ac-S pair.
8. After the new Cnt Ac-S pair is in PAIR status, stop host operations at the remote site, then
release the Cnt Ac-S pair.
9. On the intermediate site, create a Cnt Ac-J pair to the Cnt Ac-J remote site, with no data
copying (specify None on the Copy Mode option). Specify the intermediate site volume as
the Cnt Ac-J P-VOL and the remote volume as the Cnt Ac-J S-VOL.
Recovery for 3 Cnt Ac-J/Cnt Ac-S data centers and 3 Cnt Ac-J data centers 101
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- P9500 storage systems 10
- Pair volumes 11
- Journal volumes 11
- Journals 11
- Reference Information 12
- Differential data management 13
- S-VOL write option 14
- Pair status 14
- System requirements 15
- Plan and design workflow 18
- Write-workload 19
- Sizing journal volumes 20
- Planning journals 20
- RAID group configuration 21
- Planning journal volumes 22
- Planning pair volumes 22
- Planning pair volumes 23 23
- Host failover software 25
- Planning for previous models 29
- System option modes 31
- 4 Planning the data path 34
- Calculating bandwidth 35
- 36 Planning the data path 36
- Sizing bandwidth 37 37
- 38 Planning the data path 38
- Packet loss 39
- Example configuration 40
- Port types 40
- Additional switches 41
- 42 Planning the data path 42
- 5 Configuration operations 44
- 46 Configuration operations 46
- 48 Configuration operations 48
- 50 Configuration operations 50
- 52 Configuration operations 52
- 6 Pair operations 54
- Creating the initial copy 55 55
- 56 Pair operations 56
- Creating the initial copy 57 57
- Splitting pairs 58
- Splitting mirrors 59
- Creating point-in-time copies 60
- Resynchronizing pairs 60
- Resynchronizing pairs 61 61
- Resynchronizing mirrors 62
- Deleting pairs 62
- Deleting pairs 63 63
- Deleting pairs in a mirror 64
- Deleting pairs in a mirror 65 65
- 7 Monitoring the system 66
- PSUS types and behaviors 69
- PSUE types and behaviors 71
- Selecting data to be graphed 74
- Manipulating graph, save data 76
- History of pair operations 79
- 8 Maintaining the system 80
- ◦ Initial 81
- ◦ Stopped 81
- ◦ Hold(Failure) 81
- 82 Maintaining the system 82
- 84 Maintaining the system 84
- Logical path maintenance 86
- Deleting logical paths 87
- When power stops unexpectedly 88
- 90 Maintaining the system 90
- General recovery procedures 91
- Cnt Ac-J secondary site: HOLD 100
- 10 Troubleshooting 103
- Troubleshooting logical paths 105
- B9E2, B9E4, D004 109
- B9E4, D004 112
- Miscellaneous troubleshooting 121
- 122 Troubleshooting 122
- Contacting HP 123
- Related information 123
- Typographic conventions 124
- Overview 126
- Failure recovery 127
- B Sharing volumes 133
- Cache Residency 135
- Data Retention 135
- Thin Provisioning 136
- LUN Expansion 137
- LUN Manager 137
- Fast Snap and Snapshot 137
- 138 Sharing volumes 138
- Virtual LUN 139
- Auto LUN 140
- 3DC cascade configuration 141
- Delta resync configuration 144
- ◦ Use the same mirror ID 146
- Problems that can occur 148
- ◦ Assign it to other mirrors 149
- ◦ Use it with RAID Manager 149
- 2 Data center configuration 151
- Pair status and data currency 156
- E GUI reference 157
- Journal Detail window 159
- Pair Operation window 165
- Paircreate dialog box 169
- Pairsplit-r dialog box 171
- Pairresync dialog box 172
- Pairsplit-S dialog box 173
- Change Pair Option dialog box 174
- Display Filter dialog box 174
- DKC Operation window 175
- Remote systems information 176
- Logical Path Information 177
- DKC Status dialog box 179
- Add DKC dialog box 180
- DKC Option dialog box 181
- Usage Monitor window 182
- History window 183
- Operations in History window 184
- History window notes 185
- Optional Operation window 186
- Glossary 188
- 190 Index 190
- 192 Index 192
Related products and manuals for Storage Hp XP P9500 Storage
Storage Hp XP P9500 Storage User Manual
(132 pages)
(132 pages)
Storage Hp XP P9500 Storage User Manual
(113 pages)
(113 pages)
Storage Hp XP7 Storage User Manual
(304 pages)
(304 pages)
Storage Hp D2000 Disk Enclosures User Manual
(76 pages)
(76 pages)
Storage Hp Surestore NAS User Manual
(110 pages)
(110 pages)
Storage Hp Surestore 6164 Switch User Manual
(44 pages)
(44 pages)
Storage Hp 2120 Disk System User Manual
(38 pages)
(38 pages)
Storage Hp XP P9500 Storage User Manual
(81 pages)
(81 pages)
Storage Hp Optical Jukeboxes User Manual
(108 pages)
(108 pages)
Storage Hp XP P9500 Storage User Manual
(78 pages)
(78 pages)
Storage Hp XP Business Copy Software User Manual
(113 pages)
(113 pages)
Storage Hp XP Cache LUN Software User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals