Hp XP P9500 Storage User Manual Page 29
- Page / 192
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3DC configurations using 3 Cnt Ac-J sites
With Continuous Access Journal, you normally use two data centers—the primary and secondary
sites.
You can employ a third site to create a 3-data-center (3DC) configuration. Using three sites makes
a third copy of production data available in the event of primary and secondary site failure.
You can set up three Cnt Ac-J sites in multi-target or cascade configurations. You also have the
option of adding a delta resync pair.
For details, see “3 Cnt Ac-J data-center configurations” (page 126).
Planning for previous models
Continuous Access Journal can be used to perform remote copy operations between P9500 and
XP24000/XP20000 Disk Array or XP12000 Disk Array.
To perform remote copy between P9500 and XP24000/XP20000 Disk Array or XP12000 Disk
Array, observe the following:
• Configure a remote path between LDKC00 of the P9500 system and the XP24000/XP20000
Disk Array.
◦ More than one XP24000/XP20000 Disk Array can be connected to LDKC00 of P9500.
◦ LDKC01 cannot be used.
Use the configuration instructions in “Configuration operations” (page 44).
• Both systems must be set up as shown in the figure below.
Planning for previous models 29
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- P9500 storage systems 10
- Pair volumes 11
- Journal volumes 11
- Journals 11
- Reference Information 12
- Differential data management 13
- S-VOL write option 14
- Pair status 14
- System requirements 15
- Plan and design workflow 18
- Write-workload 19
- Sizing journal volumes 20
- Planning journals 20
- RAID group configuration 21
- Planning journal volumes 22
- Planning pair volumes 22
- Planning pair volumes 23 23
- Host failover software 25
- Planning for previous models 29
- System option modes 31
- 4 Planning the data path 34
- Calculating bandwidth 35
- 36 Planning the data path 36
- Sizing bandwidth 37 37
- 38 Planning the data path 38
- Packet loss 39
- Example configuration 40
- Port types 40
- Additional switches 41
- 42 Planning the data path 42
- 5 Configuration operations 44
- 46 Configuration operations 46
- 48 Configuration operations 48
- 50 Configuration operations 50
- 52 Configuration operations 52
- 6 Pair operations 54
- Creating the initial copy 55 55
- 56 Pair operations 56
- Creating the initial copy 57 57
- Splitting pairs 58
- Splitting mirrors 59
- Creating point-in-time copies 60
- Resynchronizing pairs 60
- Resynchronizing pairs 61 61
- Resynchronizing mirrors 62
- Deleting pairs 62
- Deleting pairs 63 63
- Deleting pairs in a mirror 64
- Deleting pairs in a mirror 65 65
- 7 Monitoring the system 66
- PSUS types and behaviors 69
- PSUE types and behaviors 71
- Selecting data to be graphed 74
- Manipulating graph, save data 76
- History of pair operations 79
- 8 Maintaining the system 80
- ◦ Initial 81
- ◦ Stopped 81
- ◦ Hold(Failure) 81
- 82 Maintaining the system 82
- 84 Maintaining the system 84
- Logical path maintenance 86
- Deleting logical paths 87
- When power stops unexpectedly 88
- 90 Maintaining the system 90
- General recovery procedures 91
- Cnt Ac-J secondary site: HOLD 100
- 10 Troubleshooting 103
- Troubleshooting logical paths 105
- B9E2, B9E4, D004 109
- B9E4, D004 112
- Miscellaneous troubleshooting 121
- 122 Troubleshooting 122
- Contacting HP 123
- Related information 123
- Typographic conventions 124
- Overview 126
- Failure recovery 127
- B Sharing volumes 133
- Cache Residency 135
- Data Retention 135
- Thin Provisioning 136
- LUN Expansion 137
- LUN Manager 137
- Fast Snap and Snapshot 137
- 138 Sharing volumes 138
- Virtual LUN 139
- Auto LUN 140
- 3DC cascade configuration 141
- Delta resync configuration 144
- ◦ Use the same mirror ID 146
- Problems that can occur 148
- ◦ Assign it to other mirrors 149
- ◦ Use it with RAID Manager 149
- 2 Data center configuration 151
- Pair status and data currency 156
- E GUI reference 157
- Journal Detail window 159
- Pair Operation window 165
- Paircreate dialog box 169
- Pairsplit-r dialog box 171
- Pairresync dialog box 172
- Pairsplit-S dialog box 173
- Change Pair Option dialog box 174
- Display Filter dialog box 174
- DKC Operation window 175
- Remote systems information 176
- Logical Path Information 177
- DKC Status dialog box 179
- Add DKC dialog box 180
- DKC Option dialog box 181
- Usage Monitor window 182
- History window 183
- Operations in History window 184
- History window notes 185
- Optional Operation window 186
- Glossary 188
- 190 Index 190
- 192 Index 192
Related products and manuals for Storage Hp XP P9500 Storage
Storage Hp XP P9500 Storage User Manual
(132 pages)
(132 pages)
Storage Hp XP P9500 Storage User Manual
(113 pages)
(113 pages)
Storage Hp XP7 Storage User Manual
(304 pages)
(304 pages)
Storage Hp D2000 Disk Enclosures User Manual
(76 pages)
(76 pages)
Storage Hp Surestore NAS User Manual
(110 pages)
(110 pages)
Storage Hp Surestore 6164 Switch User Manual
(44 pages)
(44 pages)
Storage Hp 2120 Disk System User Manual
(38 pages)
(38 pages)
Storage Hp XP P9500 Storage User Manual
(81 pages)
(81 pages)
Storage Hp Optical Jukeboxes User Manual
(108 pages)
(108 pages)
Storage Hp XP P9500 Storage User Manual
(78 pages)
(78 pages)
Storage Hp XP Business Copy Software User Manual
(113 pages)
(113 pages)
Storage Hp XP Cache LUN Software User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.582 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals