HP 30 30 User Manual Page 132
- Page / 218
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 6 - Parameter Description [I/O]
6-40
[3-Wire]
This function is for 3-wire start/stop control.
This function is mainly used with a momentary push button
to hold the current frequency output during acceleration or
deceleration.
[Wiring for 3-Wire Operation, P2 set to ‘3-Wire’]
[3-Wire Operation]
[Ext Trip-A]
This is a normally open contact input. When a terminal set
to ‘Ext Trip-A’ is ON, inverter displays the fault and cuts off
its output. This can be used as an external latch trip.
[Ext Trip-B]
This is a normally closed contact input. When a terminal
set to ‘Ext Trip-B’ is OFF, inverter displays the fault and
cuts off its output. This can be used as an external latch
trip.
[iTerm Clear]
This function is used for PID control. When this terminal is
ON, the accumulated value by I-Gain is set to ‘0’. Refer to
PID Control Block Diagram
.
[Open-loop]
This is used to exchange the control mode of inverter from
PID mode (Close Loop) to V/F mode (Open Loop).
DRV-03 [Drive Mode] and DRV-04 [Frequency Mode] are
applied when the mode has been changed.
☞
Note: This function can be used only when the inverter is
stopped.
[Main-drive]
When an option board (like RS485, DeviceNet, F-Net) is
installed and used for the frequency setting and the
run/stop command, the inverter operation can be changed
to manual operation using this function without changing
parameters.
FU1-02 [Frequency Mode] and FU1-01 [Drive Mode] are
applied when the mode has been changed.
☞
Note: this function can be used only when the inverter is
stopped.
[Analog hold]
When there is an analog input signal for frequency
reference and ‘Analog hold’ terminal is ON, inverter fixes
its output frequency regardless of the frequency reference
change. The changed frequency reference is applied when
the terminal is OFF.
This function is useful when a system requires constant
speed after acceleration.
[Analog hold Operation]
FX RX P2 CM
P2-CM
ON
Output Frequency
Time
Time
FX-CM
ON
Time
RX-CM
ON
Time
Freq.
Max.
Freq.
max.
P1-CM
‘Analog hold’
Reference Frequency,
Output frequency
Time
ON
Time
Reference Frequency
Output Frequency
- Series S 1
- CMC AC Variable Speed Drive 1
- WARNING 2
- OPERATING PRECAUTIONS 3
- CONTENTS 7
- 230V Class (1 ~ 30HP) 9
- 460V Class (1 ~ 30HP) 9
- 460V Class (40 ~ 100HP) 10
- CHAPTER 1 - INSTALLATION 13
- 1.4 Other Precautions 14
- 1.5 Dimensions 15
- Chapter 1 - Installation 16
- mm (inches) 17
- 1.6 Basic Wiring 19
- 1.7 Power Terminals 20
- R S T G N B1 B2 U V W 20
- R S T G P N B1 B2 U V W 20
- R S T G P1 P2 N U V W 20
- Dynamic Braking Resistor 21
- Dynamic 21
- Braking Unit 21
- WARNING 22
- Inverter Capacity 23
- 200V Class 400VClass 23
- 1.8 Control Terminals 25
- Control Board 27
- Sub-Board 27
- Option Board 27
- CHAPTER 2 - OPERATION 29
- 2.2 LCD Keypad 30
- T/K 0.0 A 31
- 00 STP 0.00 Hz 31
- 2.3 7-Segment Keypad 34
- 2.4 Operation Method 38
- 3.1 Operation using Keypad 42
- ] key three times 42
- [SHIFT/ESC] key 42
- JOG CM 43
- DRV 04 must be set at V1 44
- DRV 04 must be set at I 44
- 4.1 Function Setting 47
- 4.2 Operation Example 55
- Operation 55
- Example (1) 55
- {KeyPad-1} 56
- Example (3) 57
- motor operation 57
- Example (4) 58
- Example (5) 59
- Vector_SPD Control 59
- 5.1 Drive Group [DRV] 61
- 5.2 Function 1 Group [FU1] 63
- Chapter 5 - Parameter List 65
- 5.3 Function 2 Group [FU2] 66
- 5.5 External Group [EXT] 74
- 5.7 Application Group [APP] 79
- AutoCh-Mode 81
- AutoEx-intv 81
- 6.1 Drive group [DRV] 85
- Torque/ Output Current (LCD) 85
- DRV-01: Acceleration Time 86
- DRV-02: Deceleration Time 87
- Torque Setting Method) 88
- 10.00 05 89
- 20.00 06 89
- 30.00 07 89
- DRV-08: Output Current 90
- DRV-09: Motor Speed 90
- DRV-10: DC Link Voltage 90
- DRV-12: Fault Display 90
- 0.00Hz 91
- 6.2 Function 1 Group [FU1] 93
- FU1-03: Run Prevention 93
- FU1-06: Deceleration Pattern 93
- FU1-07: Stop Mode 94
- 5.00 08 95
- 0.10 09 95
- FU1-14: Pre-excitation Time 96
- FU1-15: Hold Time 97
- FU1-20: Maximum Frequency 97
- FU1-21: Base Frequency 97
- FU1-22: Starting Frequency 97
- FU1-29: Volts/Hz Pattern 99
- 15.00 30 100
- 15.00 36 100
- 10.0 55 102
- FU1-57: Overload Trip Level 103
- Notes: 106
- - WDOG Error 107
- FU2-07: Dwell Frequency 108
- FU2-08: Dwell Time 108
- 0000 22 110
- 1000 25 111
- FU2-38: Carrier Frequency 113
- FU2-40 ~ 44 [ Auto tuning ] 116
- 3276 45 117
- 3276 46 118
- DRV-04 [Frequency Mode] 120
- Process PID Control 121
- FU2-72: Power On Display 122
- Setting Range 123
- LCD 7-Seg 123
- Description 123
- FU2-79: Software Version 124
- FU2-81 ~ FU2-90: 2 124
- Motor Related Functions 124
- FU2-91: Parameter Read 124
- FU2-92: Parameter Write 124
- FU2-93: Parameter Initialize 125
- 4.00 07 128
- 0.00 08 128
- 60.00 10 128
- 20.00 09 128
- [Exchanging Sequence] 131
- [Up/Down Operation] 131
- FX RX P2 CM 132
- SEQ2 / 2F 133
- SEQ1 / 2F 133
- SEQ2 / 1F 133
- SEQ1 / 1F 133
- 0000 16 134
- 10.00 20 134
- I/O-43: FDT Bandwidth 136
- (380V DC or 760V DC) 139
- 6.5 External Group [EXT] 145
- EXT-01: Sub-Board Display 145
- EXT-41: AM1 Adjustment 150
- EXT-43: AM2 Adjustment 150
- 6.6 Application Group [APP] 154
- APP-02: Traverse Amplitude 155
- APP-04: Traverse Accel Time 155
- APP-05: Traverse Decel Time 155
- traverse operation 156
- APP-22: PID Bypass Selection 158
- APP-23: Sleep Delay Time 158
- APP-24: Sleep Frequency 158
- APP-25: Wake-Up Level 158
- APP-27: Auto Change Time 159
- APP-28: Auto Change Level 159
- APP-29: Inter-Lock Selection 160
- APP-30: Actual Value Display 160
- APP-32: Draw Mode Selection 160
- APP-33: Draw Size Setting 160
- Draw & Override 161
- CHAPTER 7 - OPTIONS 163
- Option Name Description 164
- 7.1 Sub-A board 166
- 7.2 Sub-B Board 168
- 169
- Chapter 7 - Options 170
- 7.3 Sub-C Board (Isolated) 172
- 7.4 Sub-D Board 174
- 7.6 External options 180
- 3) DB Resistor Wiring 182
- DB Resistor 183
- * Type 3 189
- Dimension 191
- 8.1 Fault Display 195
- Keypad Display 196
- LCD 7-Segment 196
- Protective 196
- Function 196
- 8.2 Fault Remedy 197
- Cause Remedy 198
- 8.3 Troubleshooting 199
- Condition Check Point 199
- 8.5 Maintenance 201
- DC 500V Meggar 202
- Use Related Parameter Code 205
- Application Parameter Code 206
- DRV Group 206
- FU1 Group 206
- FU2 Group 206
- I/O Group 207
- DECLARATION OF CONFORMITY 211
- TECHNICAL STANDARDS APPLIED 212
- EMC INSTALLATION GUIDE 213
- RFI FILTERS 213
- CAUTION 213
- Revisions 217
- Cleveland Motion Controls 218
Related products and manuals for Power adapters & inverters HP 30 30
(2 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 2.218 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals