HP 30 30 User Manual Page 11
- Page / 218
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
iii
Jog Jog Operation
Auto Operation Operates via Internal Sequence by Setting Multi-Function Terminal (5 Way * 8 Step)
Fault Reset Trip Status is Removed when Protection Function is Activated
Operating Status Frequency Detection Level, Overload Alarm, Stalling, Over Voltage, Under Voltage, Inverter
Overheating, Running, Stop, Constant Speed, Inverter By-Pass, Speed Searching, Auto-Operation
Step, Auto-Operation Sequence
Fault Output Contact Output (30A, 30C, 30B) – AC 250V 1A, DC 30V 1A
Output Sig.
Indicator(FM,LM) Choose 1 from Output Frequency, Output Current, Output Voltage, DC Voltage, Output Torque
Output Voltage: 0 ~ 10V (for FM: Linear output, 15V Max., LM), Pulse output: 500Hz (for LM).
Operation Function DC Braking, Frequency Limit, Frequency Jump, Second Function, Slip Compensation, Reverse
Rotation Prevention, Auto Restart, Inverter By-Pass, Auto-Tuning, PID Control
Inverter Trip Over Voltage, Under Voltage, Over Current, Fuse Open, Ground Fault, Inverter Overheating, Motor
Overheating, Output Phase Open,
Overload Protection, External Fault 1, 2, Communication Error, Loss of Speed Command, Hardware
Fault, Option Fault etc.
Inverter Alarm Stall Prevention, Overload Alarm, Temperature Sensor Fault
Protective Function
Momentary Power Loss Less than 15msec: Continuous Operation,
More than 15msec: Auto Restart Possible
Operation
Information
Output Frequency, Output Current, Output Voltage, Frequency Value Setting, Operating Speed, DC
Voltage, Output Torque
Display
Keypad
Trip
Information
Indicates a Fault when the Protection Function activates, Retains Up to 5 Faults
Ambient Temperature
-10 °C ~ 40 °C (14 °F ~ 104 °F), CE Certification: 41 °F ~ 104 °F (5 °C ~ 40 °C)
Storage Temperature
-20 °C ~ 65 °C (-4 °F ~ 149 °F)
Ambient Humidity Less Than 90 % RH Max. (Non-Condensing), CE Certification: 5 ~85% (Non-Condensing)
Altitude - Vibration
Below 1,000m or 3,300ft above sea level · Below 5.9m/sec
2
(=0.6g)
Air Pressure 86 ~ 106kPa
Environment
Application Site No Corrosive Gas, Combustible Gas, Oil Mist, or Dust
Cooling Method Forced Air Cooling
- Series S 1
- CMC AC Variable Speed Drive 1
- WARNING 2
- OPERATING PRECAUTIONS 3
- CONTENTS 7
- 230V Class (1 ~ 30HP) 9
- 460V Class (1 ~ 30HP) 9
- 460V Class (40 ~ 100HP) 10
- CHAPTER 1 - INSTALLATION 13
- 1.4 Other Precautions 14
- 1.5 Dimensions 15
- Chapter 1 - Installation 16
- mm (inches) 17
- 1.6 Basic Wiring 19
- 1.7 Power Terminals 20
- R S T G N B1 B2 U V W 20
- R S T G P N B1 B2 U V W 20
- R S T G P1 P2 N U V W 20
- Dynamic Braking Resistor 21
- Dynamic 21
- Braking Unit 21
- WARNING 22
- Inverter Capacity 23
- 200V Class 400VClass 23
- 1.8 Control Terminals 25
- Control Board 27
- Sub-Board 27
- Option Board 27
- CHAPTER 2 - OPERATION 29
- 2.2 LCD Keypad 30
- T/K 0.0 A 31
- 00 STP 0.00 Hz 31
- 2.3 7-Segment Keypad 34
- 2.4 Operation Method 38
- 3.1 Operation using Keypad 42
- ] key three times 42
- [SHIFT/ESC] key 42
- JOG CM 43
- DRV 04 must be set at V1 44
- DRV 04 must be set at I 44
- 4.1 Function Setting 47
- 4.2 Operation Example 55
- Operation 55
- Example (1) 55
- {KeyPad-1} 56
- Example (3) 57
- motor operation 57
- Example (4) 58
- Example (5) 59
- Vector_SPD Control 59
- 5.1 Drive Group [DRV] 61
- 5.2 Function 1 Group [FU1] 63
- Chapter 5 - Parameter List 65
- 5.3 Function 2 Group [FU2] 66
- 5.5 External Group [EXT] 74
- 5.7 Application Group [APP] 79
- AutoCh-Mode 81
- AutoEx-intv 81
- 6.1 Drive group [DRV] 85
- Torque/ Output Current (LCD) 85
- DRV-01: Acceleration Time 86
- DRV-02: Deceleration Time 87
- Torque Setting Method) 88
- 10.00 05 89
- 20.00 06 89
- 30.00 07 89
- DRV-08: Output Current 90
- DRV-09: Motor Speed 90
- DRV-10: DC Link Voltage 90
- DRV-12: Fault Display 90
- 0.00Hz 91
- 6.2 Function 1 Group [FU1] 93
- FU1-03: Run Prevention 93
- FU1-06: Deceleration Pattern 93
- FU1-07: Stop Mode 94
- 5.00 08 95
- 0.10 09 95
- FU1-14: Pre-excitation Time 96
- FU1-15: Hold Time 97
- FU1-20: Maximum Frequency 97
- FU1-21: Base Frequency 97
- FU1-22: Starting Frequency 97
- FU1-29: Volts/Hz Pattern 99
- 15.00 30 100
- 15.00 36 100
- 10.0 55 102
- FU1-57: Overload Trip Level 103
- Notes: 106
- - WDOG Error 107
- FU2-07: Dwell Frequency 108
- FU2-08: Dwell Time 108
- 0000 22 110
- 1000 25 111
- FU2-38: Carrier Frequency 113
- FU2-40 ~ 44 [ Auto tuning ] 116
- 3276 45 117
- 3276 46 118
- DRV-04 [Frequency Mode] 120
- Process PID Control 121
- FU2-72: Power On Display 122
- Setting Range 123
- LCD 7-Seg 123
- Description 123
- FU2-79: Software Version 124
- FU2-81 ~ FU2-90: 2 124
- Motor Related Functions 124
- FU2-91: Parameter Read 124
- FU2-92: Parameter Write 124
- FU2-93: Parameter Initialize 125
- 4.00 07 128
- 0.00 08 128
- 60.00 10 128
- 20.00 09 128
- [Exchanging Sequence] 131
- [Up/Down Operation] 131
- FX RX P2 CM 132
- SEQ2 / 2F 133
- SEQ1 / 2F 133
- SEQ2 / 1F 133
- SEQ1 / 1F 133
- 0000 16 134
- 10.00 20 134
- I/O-43: FDT Bandwidth 136
- (380V DC or 760V DC) 139
- 6.5 External Group [EXT] 145
- EXT-01: Sub-Board Display 145
- EXT-41: AM1 Adjustment 150
- EXT-43: AM2 Adjustment 150
- 6.6 Application Group [APP] 154
- APP-02: Traverse Amplitude 155
- APP-04: Traverse Accel Time 155
- APP-05: Traverse Decel Time 155
- traverse operation 156
- APP-22: PID Bypass Selection 158
- APP-23: Sleep Delay Time 158
- APP-24: Sleep Frequency 158
- APP-25: Wake-Up Level 158
- APP-27: Auto Change Time 159
- APP-28: Auto Change Level 159
- APP-29: Inter-Lock Selection 160
- APP-30: Actual Value Display 160
- APP-32: Draw Mode Selection 160
- APP-33: Draw Size Setting 160
- Draw & Override 161
- CHAPTER 7 - OPTIONS 163
- Option Name Description 164
- 7.1 Sub-A board 166
- 7.2 Sub-B Board 168
- 169
- Chapter 7 - Options 170
- 7.3 Sub-C Board (Isolated) 172
- 7.4 Sub-D Board 174
- 7.6 External options 180
- 3) DB Resistor Wiring 182
- DB Resistor 183
- * Type 3 189
- Dimension 191
- 8.1 Fault Display 195
- Keypad Display 196
- LCD 7-Segment 196
- Protective 196
- Function 196
- 8.2 Fault Remedy 197
- Cause Remedy 198
- 8.3 Troubleshooting 199
- Condition Check Point 199
- 8.5 Maintenance 201
- DC 500V Meggar 202
- Use Related Parameter Code 205
- Application Parameter Code 206
- DRV Group 206
- FU1 Group 206
- FU2 Group 206
- I/O Group 207
- DECLARATION OF CONFORMITY 211
- TECHNICAL STANDARDS APPLIED 212
- EMC INSTALLATION GUIDE 213
- RFI FILTERS 213
- CAUTION 213
- Revisions 217
- Cleveland Motion Controls 218
Related products and manuals for Power adapters & inverters HP 30 30
(2 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 1.516 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals