HP 30 30 User Manual Page 99
- Page / 218
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 6 - Parameter description [FU1]
6-15
☞ Note: When FU2-40 [Control Mode] is set to ‘Sensorless’,
the torque boost value is the rate per thousand of inverter
rated voltage.
[Auto Torque Boost]: Inverter outputs high starting torque
by automatic boosting according to the load.
☞
Note: Auto torque boost is only available for the 1
st
motor.
Manual torque boost must be used for the 2
nd
motor.
☞ Note: The auto torque boost value is added to the manual
torque boost value.
☞ Note: Auto torque boost is available only when FU2-40
[Control Mode] is set to ‘V/F’.
☞ Note: Conduct Auto tuning in FU2-41 [Auto tuning] to use
Auto torque boost effectively.
[Constant Torque Loads: Conveyor, Moving Equip. etc.]
[Ascending and Descending Loads: Parking, Hoist etc.]
FU1-29: Volts/Hz Pattern
This is the pattern of voltage/frequency ratio. Select the
proper V/F pattern according to the load. The motor torque
is dependent on this V/F pattern.
[Linear] pattern is used where constant torque is required.
This pattern maintains a linear volts/frequency ratio from
zero to base frequency. This pattern is appropriate for
constant torque applications.
[Square] pattern is used where variable torque is required.
This pattern maintains squared volts/hertz ratio. This
pattern is appropriate for fans, pumps, etc.
[User V/F] pattern is used for special applications. Users
can adjust the volts/frequency ratio according to the
application. This is accomplished by setting the voltage
and frequency, respectively, at four points between starting
frequency and base frequency. The four points of voltage
and frequency are set in FU1-30 through FU1-37.
[V/F Pattern: ‘Linear’]
Output Voltage
Output
Frequency
Freq. Base
100%
Manual
Boost
Value
Forward and Reverse direction
(Set the same value for FU1-27
and FU1-28)
Output Voltage
Output
Frequency
FU1-21
100%
Manual
Boost
Value
Forward Direction - Motoring
(Set FU1-27 to a value)
Reverse Direction - Regenerating
(Set FU1-28 to ‘0’)
FU1
►
V/F pattern
29 Linear
0 29
Factory Default: Linear 0
Related Functions: FU1-29 [Volts/Hz Pattern]
FU2-40 [Control Mode selection]
Output Voltage
Output
Frequency
Freq. Base
100%
- Series S 1
- CMC AC Variable Speed Drive 1
- WARNING 2
- OPERATING PRECAUTIONS 3
- CONTENTS 7
- 230V Class (1 ~ 30HP) 9
- 460V Class (1 ~ 30HP) 9
- 460V Class (40 ~ 100HP) 10
- CHAPTER 1 - INSTALLATION 13
- 1.4 Other Precautions 14
- 1.5 Dimensions 15
- Chapter 1 - Installation 16
- mm (inches) 17
- 1.6 Basic Wiring 19
- 1.7 Power Terminals 20
- R S T G N B1 B2 U V W 20
- R S T G P N B1 B2 U V W 20
- R S T G P1 P2 N U V W 20
- Dynamic Braking Resistor 21
- Dynamic 21
- Braking Unit 21
- WARNING 22
- Inverter Capacity 23
- 200V Class 400VClass 23
- 1.8 Control Terminals 25
- Control Board 27
- Sub-Board 27
- Option Board 27
- CHAPTER 2 - OPERATION 29
- 2.2 LCD Keypad 30
- T/K 0.0 A 31
- 00 STP 0.00 Hz 31
- 2.3 7-Segment Keypad 34
- 2.4 Operation Method 38
- 3.1 Operation using Keypad 42
- ] key three times 42
- [SHIFT/ESC] key 42
- JOG CM 43
- DRV 04 must be set at V1 44
- DRV 04 must be set at I 44
- 4.1 Function Setting 47
- 4.2 Operation Example 55
- Operation 55
- Example (1) 55
- {KeyPad-1} 56
- Example (3) 57
- motor operation 57
- Example (4) 58
- Example (5) 59
- Vector_SPD Control 59
- 5.1 Drive Group [DRV] 61
- 5.2 Function 1 Group [FU1] 63
- Chapter 5 - Parameter List 65
- 5.3 Function 2 Group [FU2] 66
- 5.5 External Group [EXT] 74
- 5.7 Application Group [APP] 79
- AutoCh-Mode 81
- AutoEx-intv 81
- 6.1 Drive group [DRV] 85
- Torque/ Output Current (LCD) 85
- DRV-01: Acceleration Time 86
- DRV-02: Deceleration Time 87
- Torque Setting Method) 88
- 10.00 05 89
- 20.00 06 89
- 30.00 07 89
- DRV-08: Output Current 90
- DRV-09: Motor Speed 90
- DRV-10: DC Link Voltage 90
- DRV-12: Fault Display 90
- 0.00Hz 91
- 6.2 Function 1 Group [FU1] 93
- FU1-03: Run Prevention 93
- FU1-06: Deceleration Pattern 93
- FU1-07: Stop Mode 94
- 5.00 08 95
- 0.10 09 95
- FU1-14: Pre-excitation Time 96
- FU1-15: Hold Time 97
- FU1-20: Maximum Frequency 97
- FU1-21: Base Frequency 97
- FU1-22: Starting Frequency 97
- FU1-29: Volts/Hz Pattern 99
- 15.00 30 100
- 15.00 36 100
- 10.0 55 102
- FU1-57: Overload Trip Level 103
- Notes: 106
- - WDOG Error 107
- FU2-07: Dwell Frequency 108
- FU2-08: Dwell Time 108
- 0000 22 110
- 1000 25 111
- FU2-38: Carrier Frequency 113
- FU2-40 ~ 44 [ Auto tuning ] 116
- 3276 45 117
- 3276 46 118
- DRV-04 [Frequency Mode] 120
- Process PID Control 121
- FU2-72: Power On Display 122
- Setting Range 123
- LCD 7-Seg 123
- Description 123
- FU2-79: Software Version 124
- FU2-81 ~ FU2-90: 2 124
- Motor Related Functions 124
- FU2-91: Parameter Read 124
- FU2-92: Parameter Write 124
- FU2-93: Parameter Initialize 125
- 4.00 07 128
- 0.00 08 128
- 60.00 10 128
- 20.00 09 128
- [Exchanging Sequence] 131
- [Up/Down Operation] 131
- FX RX P2 CM 132
- SEQ2 / 2F 133
- SEQ1 / 2F 133
- SEQ2 / 1F 133
- SEQ1 / 1F 133
- 0000 16 134
- 10.00 20 134
- I/O-43: FDT Bandwidth 136
- (380V DC or 760V DC) 139
- 6.5 External Group [EXT] 145
- EXT-01: Sub-Board Display 145
- EXT-41: AM1 Adjustment 150
- EXT-43: AM2 Adjustment 150
- 6.6 Application Group [APP] 154
- APP-02: Traverse Amplitude 155
- APP-04: Traverse Accel Time 155
- APP-05: Traverse Decel Time 155
- traverse operation 156
- APP-22: PID Bypass Selection 158
- APP-23: Sleep Delay Time 158
- APP-24: Sleep Frequency 158
- APP-25: Wake-Up Level 158
- APP-27: Auto Change Time 159
- APP-28: Auto Change Level 159
- APP-29: Inter-Lock Selection 160
- APP-30: Actual Value Display 160
- APP-32: Draw Mode Selection 160
- APP-33: Draw Size Setting 160
- Draw & Override 161
- CHAPTER 7 - OPTIONS 163
- Option Name Description 164
- 7.1 Sub-A board 166
- 7.2 Sub-B Board 168
- 169
- Chapter 7 - Options 170
- 7.3 Sub-C Board (Isolated) 172
- 7.4 Sub-D Board 174
- 7.6 External options 180
- 3) DB Resistor Wiring 182
- DB Resistor 183
- * Type 3 189
- Dimension 191
- 8.1 Fault Display 195
- Keypad Display 196
- LCD 7-Segment 196
- Protective 196
- Function 196
- 8.2 Fault Remedy 197
- Cause Remedy 198
- 8.3 Troubleshooting 199
- Condition Check Point 199
- 8.5 Maintenance 201
- DC 500V Meggar 202
- Use Related Parameter Code 205
- Application Parameter Code 206
- DRV Group 206
- FU1 Group 206
- FU2 Group 206
- I/O Group 207
- DECLARATION OF CONFORMITY 211
- TECHNICAL STANDARDS APPLIED 212
- EMC INSTALLATION GUIDE 213
- RFI FILTERS 213
- CAUTION 213
- Revisions 217
- Cleveland Motion Controls 218
Related products and manuals for Power adapters & inverters HP 30 30
(2 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 1.740 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals