Hp ProLiant ML350 G6 Server User Manual Page 50
- Page / 144
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Hardware options installation 50
• UDIMM
o First: A and B
o Last: D and E
o Do not populate slots C, F, G, H, or I.
After installing the DIMMs, use RBSU to configure the system for Mirrored Memory support ("Configuring
mirrored memory" on page 93).
Multi-processor Mirrored Memory population order
For Mirrored Memory mode configurations with multiple processors, populate the DIMM slots for each
processor in the following order:
• RDIMM
o First: A and B
o Next: D and E
o Last: G and H
o Do not populate slots C, F, or I.
• UDIMM
o First: A and B
o Last: D and E
o Do not populate slots C, F, G, H, or I.
After installing the DIMMs, use RBSU to configure the system for mirrored memory support ("Configuring
mirrored memory" on page 93).
Lockstep Memory population guidelines
For Lockstep memory mode configurations, observe the following guidelines:
• Observe the general DIMM slot population guidelines (on page 48).
• Always install DIMMs in channels 1 and 2 for each installed processor.
• Do not install DIMMs in channel 3 for any processor.
• DIMM configuration on channel 1 and channel 2 of a processor must be identical.
• In multi-processor configurations, each processor must have a valid Lockstep Memory configuration.
• In multi-processor configurations, each processor may have a different valid Lockstep Memory
configuration.
Single-processor Lockstep population order
For Lockstep memory mode configurations with a single processor, populate the DIMM slots in the following
order:
• RDIMM
o First: A and B
o Next: D and E
o Last: G and H
- HP ProLiant ML350 G6 Server 1
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Contents 6 6
- Component identification 7
- Front panel LEDs and buttons 8
- Rear panel components 9
- Rear panel LEDs and buttons 10
- System board components 11
- Item Description 12
- System board LEDs 13
- NMI functionality 14
- System maintenance switch 14
- SAS/SATA device numbers 15
- SAS and SATA hard drive LEDs 16
- Online/activity 17
- LED (green) 17
- Fault/UID LED 17
- (amber/blue) 17
- Interpretation 17
- Battery pack LEDs 18
- FBWC module LEDs 19
- • Fan locations 20
- Operations 24
- Remove the access panel 26
- Install the access panel 27
- Remove the media bay blank 27
- Remove the DIMM baffle 28
- Remove a fan blank 29
- Optimum environment 30
- Temperature requirements 31
- Rack planning resources 32
- Rack warnings 32
- Setup 33 33
- Installing hardware options 34
- Setting up a tower server 34
- Setup 35 35
- Registering the server 36
- Introduction 37
- Processor option 37
- Install the heatsink 42
- Memory options 44
- DIMM identification 45
- Memory configurations 46
- Low voltage DIMMs 47
- Installing DIMMs 51
- To install the component: 53
- Remove the hard drive blank 53
- Hard drive cage options 54
- Identifying guide screws 63
- Power supply configuration 68
- Expansion board options 69
- PCI-X expansion cage option 72
- 7. Install the FBWC module 81
- 8. Connect the cable 81
- • T-10 Torx screwdriver 88
- • T-15 Torx screwdriver 88
- Configuration and utilities 91
- HP ROM-Based Setup Utility 92
- Boot options 93
- BIOS Serial Console 93
- Configuring mirrored memory 93
- Array Configuration Utility 94
- Management tools 96
- Erase Utility 97
- Redundant ROM support 97
- Diagnostic tools 98
- Integrated Management Log 99
- Keeping the system current 100
- Care Pack 101
- Troubleshooting 102
- Symbols on equipment 103
- Warnings and cautions 103
- Symptom information 104
- Loose connections 106
- Service notifications 107
- Server health LEDs 107
- Troubleshooting flowcharts 107
- General diagnosis flowchart 108
- Symptoms: 110
- Troubleshooting 112 112
- POST problems flowchart 113
- OS boot problems flowchart 115
- Troubleshooting 116 116
- • Redundancy failure 117
- (http://www.hp.com/support) 118
- Troubleshooting 119 119
- Battery replacement 120
- FCC rating label 121
- Modifications 122
- • EMC Directive 2004/108/EC 123
- Japanese notice 124
- BSMI notice 124
- Korean notice 124
- Chinese notice 125
- Laser compliance 125
- Battery replacement notice 125
- Electrostatic discharge 127
- Server specifications 128
- Technical support 131
- Technical support 132 132
- Customer Self Repair 133
- Technical support 134 134
- Reparo feito pelo cliente 135
- Technical support 136 136
- Technical support 137 137
- Technical support 138 138
- Acronyms and abbreviations 139
- Index 142 142
- Index 143 143
- Index 144 144
Related products and manuals for Computer hardware Hp ProLiant ML350 G6 Server
(122 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 2.656 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals