HP 280 G1 Specifications Page 25
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
●
If you remove a key, use a specially designed key puller to prevent damage to the keys. This tool is
available through many electronic supply outlets.
CAUTION: Never remove a wide leveled key (like the space bar) from the keyboard. If these keys are
improperly removed or installed, the keyboard may not function properly.
●
Cleaning under a key may be done with a swab moistened with isopropyl alcohol and squeezed out. Be
careful not to wipe away lubricants necessary for proper key functions. Use tweezers to remove any
fibers or dirt in confined areas. Allow the parts to air dry before reassembly.
Cleaning the monitor
●
Wipe the monitor screen with a clean cloth moistened with water or with a towelette designed for
cleaning monitors. Do not use sprays or aerosols directly on the screen; the liquid may seep into the
housing and damage a component. Never use solvents or flammable liquids on the monitor.
●
To clean the monitor body follow the procedures in
Cleaning the Computer Case on page 16.
Cleaning the mouse
Before cleaning the mouse, ensure that the power to the computer is turned off.
●
Clean the mouse ball by first removing the retaining plate and the ball from the housing. Pull out any
debris from the ball socket and wipe the ball with a clean, dry cloth before reassembly.
●
To clean the mouse body, follow the procedures in Cleaning the Computer Case on page 16.
Service considerations
Listed below are some of the considerations that you should keep in mind during the disassembly and
assembly of the computer.
Power supply fan
The power supply fan is a variable-speed fan based on the temperature in the power supply.
CAUTION: The cooling fan is always on when the computer is in the “On” mode. The cooling fan is off when
the computer is in “Standby,” “Suspend,” or “Off” modes.
You must disconnect the power cord from the power source before opening the computer to prevent system
board or component damage.
Tools and software Requirements
To service the computer, you need the following:
●
Torx T-15 screwdriver
●
Torx T-15 screwdriver with small diameter shank (for certain front bezel removal)
●
Flat-bladed screwdriver (may sometimes be used in place of the Torx screwdriver)
●
Phillips #2 screwdriver
●
Diagnostics software
●
Tamper-resistant T-15 wrench
Service considerations 17
- Maintenance and Service Guide 1
- Safety warning notice 3
- Table of contents 5
- 1 Product description 9
- 2 Product Features 12
- Front panel components 13
- Rear panel components 14
- Rear panel components 7 15
- Serial Number Location 16
- 3 Illustrated parts catalog 17
- Misc parts 19
- Generating static 21
- Grounding the work area 22
- Operating guidelines 23
- Routine care 24
- Service considerations 25
- Cables and connectors 26
- Hard Drives 26
- Lithium coin cell battery 26
- SATA hard drives 27
- SATA hard drive cables 27
- SMART ATA drives 27
- Cable management 28
- Preparation for disassembly 29
- Access panel 30
- Front bezel 31
- Optical drive bezel blank 32
- DDR3/DDR3L-SDRAM UDIMMs 33
- Populating DIMM sockets 33
- Installing DIMMs 34
- Expansion cards 35
- Drive positions 39
- Removing an optical drive 40
- Removing a hard drive 41
- Card reader 45
- Heat sink 47
- Processor 48
- 7. Remove the speaker 51
- Speaker 43 51
- Rear chassis fan 52
- Rear chassis fan 45 53
- Hood sensor 54
- Power supply 55
- System board 57
- System board callouts 58
- Computer Setup—File 61
- Computer Setup—Storage 62
- Computer Setup—Security 63
- Computer Setup—Power 66
- Computer Setup—Advanced 67
- Safety and comfort 70
- Helpful hints 71
- Solving general problems 72
- Solving general problems 65 73
- Solving general problems 67 75
- Solving power problems 76
- Solving hard drive problems 77
- Solving display problems 80
- Solving display problems 73 81
- Solving display problems 75 83
- Solving audio problems 84
- Solving audio problems 77 85
- Solving printer problems 86
- Solving Network Problems 91
- Solving Network Problems 85 93
- Solving memory problems 94
- Solving software problems 100
- Solving software problems 93 101
- 8 POST error messages 102
- 10 HP PC Hardware Diagnostics 114
- 11 System backup and recovery 116
- Creating recovery media 119
- System Restore 121
- System Recovery 122
- Recommended Applications 125
- A Battery replacement 126
- B Power Cord Set Requirements 128
- Country-Specific Requirements 129
- C Statement of Volatility 130
- D Specifications 132
- ERecycling 133
Related products and manuals for Mini PCs HP 280 G1
Mini PCs HP 230 User's Guide
(59 pages)
(59 pages)
Mini PCs HP QT068AW Datasheet
(3 pages)
(3 pages)
Mini PCs HP LX869ET Datasheet
(3 pages)
(3 pages)
Mini PCs HP BM424AA Datasheet
(2 pages)
(2 pages)
Mini PCs HP Z440 User's Guide
(55 pages)
(55 pages)
Mini PCs HP GQ796ES#ABE Datasheet
(60 pages)
(60 pages)
Mini PCs HP 800 G1 USDT Quick Specifications
(72 pages)
(72 pages)
Mini PCs HP 405 G1 Quick Specifications
(51 pages)
(51 pages)
Mini PCs HP 490 G2 Quick Specifications
(72 pages)
(72 pages)
Mini PCs HP 490 G1 Quick Specifications
(55 pages)
(55 pages)
Mini PCs HP 405 G1 Quick Specifications
(57 pages)
(57 pages)
Mini PCs HP SN279UP Datasheet
(65 pages)
(65 pages)
Mini PCs HP 600 MT Quick Specifications
(63 pages)
(63 pages)
Mini PCs HP 600 G1 TWR Quick Specifications
(57 pages)
(57 pages)
Mini PCs HP 800 G1 Quick Specifications
(62 pages)
(62 pages)
Mini PCs HP 420 Quick Specifications
(67 pages)
(67 pages)
Mini PCs HP 230 TWR Quick Specifications
(58 pages)
(58 pages)
Mini PCs HP 400 G1 Specifications
(242 pages)
(242 pages)
© 2020, manymanuals.com. All rights reserved. | 2.133 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals