HP ProCurve 5400zl User Manual Page 18
- Page / 118
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-8
Introducing the ProCurve Series 5400zl Switches
Front of the Switch
Introducing the ProCurve
Series 5400zl Switches
Table 1-2. Switch Module LEDs
These LEDs are located on the modules themselves, one pair for each port.
LED Mode Select
(5 green LEDs)
Act Indicates that the port Mode LEDs are displaying network activity information.
FDx Indicates that the port Mode LEDs are lit for ports that are in Full Duplex Mode.
PoE Indicates which ports are supplying PoE power.
• If the Mode LED is on the port is providing PoE power.
• If the Mode LED is off the port is not providing PoE power.
• If the Link LED is on the port is enabled for PoE.
• If the Link LED is off the port is disabled for PoE.
• If the Link LED is blinking, the port has an error or the port is denied power due to
insufficient power.
Spd Indicates the Port LEDs are displaying the connection speed at which each port is
operating:
• if the Port LED is off, the port is operating at 10 Mbps
• if the Port LED is blinking, the port is operating at 100 Mbps
• if the Port LED is on continuously, the port is operating at 1000 Mbps
Usr Reserved for future development
Auxiliary (green/
Orange)
Reserved for future development
1
The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.
2
The blinking behavior is an on/off cycle once every 0.5 seconds, approximately.
LEDs State Meaning
LED State Meaning
Link On Indicates the port is enabled and receiving a link beat signal (for the twisted-pair
ports), or a strong enough light level (for the fiber-optic ports) from the connected
device.
Off One of these conditions exists:
• no active network cable is connected to the port
• the port is not receiving link beat or sufficient light
• the port has been disabled through the switch console, the web browser
interface, ProCurve Manager, or other network management tool.
Blinking
1
The port has failed self test. The switch Fault, Self Test LEDs, and appropriate
module status LEDs will flash simultaneously.
Mode Depending on the mode selected, displays the following: network activity information, whether
the port is configured for Full Duplex operation, maximum speed operation, or whether PoE
power is being supplied or not. See “LED Mode Select Button and Indicator LEDs” below for
more information.
1
The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.
- Installation and 1
- Getting Started Guide 1
- Contents 5
- 4 Replacing Components 6
- 5 Troubleshooting 7
- A Specifications 7
- D Recycle Statements 9
- 5400zl Switches 11
- Front of the Switch 15
- Introducing the ProCurve 17
- Series 5400zl Switches 17
- Table 1-2. Switch Module LEDs 18
- Console Port 20
- Reset Button 20
- Clear Button 20
- Back of the Switch 21
- Power Connector 22
- Redundant Power Supply 22
- Switch Features 23
- Included Parts 25
- Japan Power 26
- Cord Warning 26
- Installation Procedures 27
- Installation Precautions 29
- Cautions 30
- Cabling Infrastructure 31
- Installation Location 32
- 2. Install Switch Modules 33
- Installing the Series 5400zl 34
- Switches 34
- CAUTION: 37
- LED Behavior: 40
- 5.Mount the Switch 41
- Horizontal Surface Mounting 44
- 6. Install the Grounding Wire 45
- to the switch 46
- Power Supply Shelf LEDs 47
- Terminal Configuration 50
- Direct Console Access 51
- Telnet Console Access 51
- Hot Swapping Switch Modules 52
- Example Network Topologies 53
- Use as an Edge Switch 54
- Using the Switch Setup Screen 56
- Where to Go From Here 58
- Management 59
- PoE Status 60
- Replacing Components 61
- Replacing Power Supplies 62
- Replacing Fan Trays 64
- Compact Flash Card 66
- Installing a New Battery 67
- Troubleshooting 69
- Basic Troubleshooting Tips 70
- Diagnosing with the LEDs 72
- Diagnostic Tips: 73
- Proactive Networking 77
- Hardware Diagnostic Tests 78
- Testing Twisted-Pair Cabling 79
- Configuration 80
- Downloading New Code 81
- HP Customer Support Services 81
- Specifications 83
- Environmental 84
- Acoustic 85
- Network Connectors 85
- Switch Ports 87
- Twisted-Pair 88
- Fiber-Optic Cables 89
- Copper Cables 90
- Gigabit-LX 91
- Installing the Patch Cord 92
- Cable Diagram 94
- Pin Assignments 94
- 1000 Mbps Network Connections 96
- Safety Information 97
- Hinweise zur Sicherheit 99
- Safety and Regulatory 100
- Statements 100
- Safety Information (Japan) 102
- Safety Information (China) 103
- EMC Regulatory Statements 104
- European Community 106
- Recycle Statements 107
- Numerics 111
- 2 – Index 112
- Index – 3 113
- 4 – Index 114
- Index – 5 115
- 6 – Index 116
- *5991-4741* 118
© 2020, manymanuals.com. All rights reserved. | 0.771 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals