HP HSR6600 Installation Manual Page 64
- Page / 107
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
58
Viewing the system fault solving method
Use the display system-failure command to display the system fault solving method.
<Sysname> display system-failure
System failure handling method: reboot
Saving the current configuration of the router
You can save the current configuration of the router in one of the following methods:
• Fast saving—Executing the save command without the safely keyword. This mode saves the file
more quickly but is likely to lose the existing configuration file if the router reboots or the power fails
during the process. The fast saving mode is suitable for environments where the power supply is
stable.
• Safe saving—Executing the save command with the safely keyword. The mode saves the file more
slowly but can retain the configuration file in the router even if the router reboots or the power fails
during the process. The safe saving mode is preferred in environments where a stable power supply
is unavailable or remote maintenance is involved.
Table 19 To save the current configuration of the router:
Pur
p
ose Command Remarks
Save the current configuration to the specified file, but the
configuration file will not be set as the file for the next startup
save file-url
Use either
command
Available in any
view
Save the current configuration to the root directory of the storage
medium of the active or standby device and specify the file as the
startup configuration file that will be used at the next system startup
save [ safely ]
NOTE:
• The configuration file must be with extension .cfg.
• Durin
g
the execution of the save command, the startup confi
g
uration file to be used at the next system
startup may be lost if the router reboots or the power supply fails. In this case, the router will boot with
the factory defaults, and after the router reboots, you need to re-specify a startup confi
g
uration file for
the next system startup.
Rebooting the router
When upgrading and maintaining the startup configuration file or configuration file for the router, you
need to reboot the router. To reboot a router, use one of the following methods:
• Use the reboot command to reboot a router.
• Enable the scheduled reboot function at the CLI. You can set a time at which the router can
automatically reboot, or set a delay so that the router can automatically reboot within the delay.
• Power on the router after powering it off, which is also called hard reboot or cold start. Powering off
a running router causes data loss and hardware damages, and therefore is not recommended.
• Use the RESET button.
- HP HSR6600 Routers 1
- Contents 3
- Preparing for installation 7
- Electricity 8
- Laser safety 8
- Router moving 8
- Weight support 8
- Temperature and humidity 9
- Altitude 9
- Cleanness 9
- Cooling system 10
- ESD prevention 10
- Lightning protection 12
- Power supply 12
- Accessories 13
- Installing the router 14
- Unpacking the router 15
- Grounding the router 17
- Grounding cable 18
- Installing a power module 19
- Installing a FIP module 19
- Installing a HIM/MIM 20
- Installing a CF card 21
- Connecting the power cord 22
- Connecting the AUX cable 24
- Connecting an Ethernet cable 25
- Connecting a fiber cable 27
- Fiber cable overview 28
- Connecting an E1/T1 cable 31
- Connecting a T1 cable 33
- Connecting a CE3/CT3 cable 34
- Overview 35
- Login methods 39
- Setting terminal parameters 40
- Verification before power-on 43
- Powering on the router 43
- HP A6600 Routers 44
- Configuration Guides 44
- Configuring basic settings 45
- Replacement procedures 47
- Replacing a FIP module 48
- Replacing a HIM/MIM 48
- Replacing a CF card 49
- Replacing a fan tray 51
- Replacing a memory module 52
- Memory module structure 53
- Power 1 State: Absent 60
- Power 2 State: Normal 60
- Solving system faults 63
- Rebooting the router 64
- Troubleshooting 66
- FIP module failure 67
- Power module failures 67
- Fan failures 68
- HIM/MIM failures 69
- Dealing with password loss 70
- 1. Reboot the router 71
- EXTEND-BOOTWARE menu 72
- Cooling system failure 75
- Software upgrade failures 76
- FTP upgrade failure 77
- Booting App fails! 78
- Chassis views 79
- Dimensions and weights 80
- Storage media 81
- Power consumption 81
- Power module 81
- DC power module 82
- Fan tray 83
- Port specifications 84
- Management Ethernet port 85
- Combo interface 85
- 10 Gbps Ethernet port 86
- Interface modules 89
- Appendix B LEDs 90
- FIP LEDs 93
- HIM/MIM LEDs 94
- Power module LEDs 94
- Appendix C Cable management 95
- Cable management guidelines 96
- Cable routing example 98
- Figure 83 Routing cables 99
- Slot arrangement 100
- Slot arrangement for FIPs 100
- Numbering interfaces 101
- Examples 101
- • GigabitEthernet 1/2/2 102
- • GigabitEthernet 1/2/3 102
- Support and other resources 103
- Conventions 104
- Network topology icons 105
- Port numbering in examples 105
- A C D E F G H I L N P R S U 106
Related products and manuals for Network equipment chassis HP HSR6600
(58 pages)© 2020, manymanuals.com. All rights reserved. | 0.838 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals