Hp Insight Management Agents User Manual Page 93
- Page / 165
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
• Not Preserved - No Drive Support—The statistics are not saved across power cycles because
the physical drive does not contain a unique identifier to save it.
• Not Preserved - No Software Support—The statistics are not saved across power cycles because
software does not provide support.
• Unknown—The Storage Agents cannot determine the status. You may need to upgrade your
driver software or Storage Agents.
SCSI logical drives
Select a SCSI logical drive from the SCSI controller submenu to display the following information.
The following values are valid:
• Status—Shows the status of the physical drive selected.
OK—The logical drive is in normal operation mode. No user action is required.◦
◦ Failed—There are more failed physical drives than the fault tolerance mode of the logical
drive can handle without data loss.
◦ Unconfigured—The logical drive is not configured. Run the logical drive configuration
utility to configure the logical drive.
◦ Recovering—The logical drive is using Interim Recovery Mode. In Interim Recovery Mode,
at least one physical drive has failed, but the logical drive’s fault tolerance mode lets the
logical drive continue to operate with no data loss. You should replace the failed drive
as soon as possible.
◦ Ready for Rebuild—The logical drive is ready for Automatic Data Recovery. The physical
drive that failed has been replaced, but the logical drive is still operating in Interim
Recovery Mode.
◦ Rebuilding—The logical drive is currently re-synchronizing the data across the physical
drives in the logical drive.
◦ Wrong Drive—The wrong physical drive was replaced after a physical drive failure. You
must return the drive incorrectly replaced and replace the failed drive.
◦ Bad Connection—A physical drive is not responding. Check the cables connecting the
physical drive.
◦ Degraded—The logical drive is in a degraded state.
◦ Disabled—The logical drive is disabled. The logical drive configuration utility can enable
or disable the logical drive. • Unknown—The Storage Agents cannot determine the status
of this drive. You might need to upgrade your driver software or Storage Agents.
• Capacity—Displays the size of the logical drive.
• Fault Tolerance—Displays the fault tolerance mode of the logical drive. The following values
are valid:
◦ None—(RAID 0) fault tolerance is not enabled. If a physical drive reports an error, the
data cannot be recovered.
◦ Mirroring—(RAID 1/RAID 0+1) is the highest level of fault tolerance. It is the only method
offering fault tolerance protection if no more than two physical drives are selected. Drive
mirroring creates fault tolerance by storing duplicate data on two drives. There must be
an even number of drives. This is the most costly fault tolerance method because it requires
50 percent of the drive capacity to store the redundant data.
◦ Data Guarding—(RAID 4) assures data reliability while using only a small percent of the
logical drive storage capacity. A designated, single physical drive contains parity data.
If a drive fails, the controller uses the data on the parity drive and the data on the
remaining drives to reconstruct data from the failed drive. This allows the system to continue
operating with slightly reduced performance until you replace the drive.
Storage agent 93
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 8 Contents 8
- Browser requirements 9
- Obtaining JVM from HP.com 10
- Obtaining JVM from Oracle 10
- Security 11
- Introduction 13
- Overview 13
- Logging in 13
- System Management Homepage 15
- Switch to icon view 17
- Body frame 18
- Home tab 18
- Overall System Health Status 19
- Component Status Summary 19
- Management processor 19
- Operating system 20
- System configuration 20
- Version control 20
- Settings tab 21
- UI properties 24
- User Preferences 24
- Tasks tab 25
- Logs tab 25
- Webapps tab 25
- Help tab 26
- Support tab 26
- 2 Agent information 27
- Threshold Agent 28
- System Agent 28
- Cluster resources groups 29
- Cluster networks 29
- Storage agent 30
- IDE ATA disk drives 31
- IDE ATA logical drives 32
- Drive Array Controllers 33
- 34 Agent information 34
- Storage agent 35 35
- Array Accelerator Information 36
- Storage agent 37 37
- 38 Agent information 38
- Storage agent 39 39
- 40 Agent information 40
- Physical Drive Information 41
- 42 Agent information 42
- Storage agent 43 43
- 44 Agent information 44
- Spare Information 45
- Predictive Indicators 46
- Problem Indicators 47
- Failure Indicators 48
- Storage agent 49 49
- Statistics 50
- Logical Drive Information 51
- 52 Agent information 52
- Storage agent 53 53
- 54 Agent information 54
- Storage agent 55 55
- Tape Drive Information 56
- Storage agent 57 57
- Storage Systems 58
- Storage agent 59 59
- 60 Agent information 60
- Storage System Information 61
- 62 Agent information 62
- Storage agent 63 63
- 64 Agent information 64
- Storage agent 65 65
- 66 Agent information 66
- Array Controller Information 67
- 68 Agent information 68
- Accelerator Information 69
- 70 Agent information 70
- 72 Agent information 72
- Storage agent 73 73
- Storage agent 75 75
- 76 Agent information 76
- Snapshot Resource Volumes 77
- 78 Agent information 78
- RAID Array Storage Systems 79
- External Storage Connections 79
- 80 Agent information 80
- SCSI Controllers 81
- SCSI device information 82
- Tape library 83
- 84 Agent information 84
- Tape devices 85
- CD storage system 86
- Storage systems 87
- 88 Agent information 88
- SCSI physical drives 89
- Drive indicators 90
- Drive statistics 91
- Statistics Preserved 92
- SCSI logical drives 93
- 94 Agent information 94
- SCSI bus information 95
- SAS Host Bus Adapter 96
- SAS Physical Drive 97
- 98 Agent information 98
- SAS Logical Drive 99
- SAS Tape Drive 100
- SAS Storage System 101
- 102 Agent information 102
- Session Information 103
- 104 Agent information 104
- Connect Information 105
- Sub-system Classification 106
- Cooling and temperature 107
- 108 Agent information 108
- Sub-system Classification 109 109
- 110 Agent information 110
- Memory Summary 111
- Memory Details 112
- Processors 113
- PCI Devices 113
- Management Processor 114
- Modem/COM Port Settings 115
- Self Test Results 116
- Operating System 117
- Logical Disk Space 118
- Sub-system Classification 119 119
- 120 Agent information 120
- Sub-system Classification 121 121
- 122 Agent information 122
- Processor Utilization 123
- System Configuration 124
- Sub-system Classification 125 125
- System Board 126
- Sub-system Classification 127 127
- 128 Agent information 128
- Sub-system Classification 129 129
- 130 Agent information 130
- System Resources 131
- System Summary 131
- Enclosure Information 132
- Sub-system Classification 133 133
- 134 Agent information 134
- Sub-system Classification 135 135
- 136 Agent information 136
- Critical Error Log 137
- 138 Agent information 138
- Correctable errors 139
- Power-On Messages 139
- Integrated Management Log 139
- 140 Agent information 140
- Operating system overview 141
- Summary page 141
- File System page 142
- User Information page 143
- Connection page 143
- Loaded NLMs page 144
- Server Parameter page 144
- Physical Partition page 145
- Adapter Information page 145
- Mass storage RAID Array 146
- Mass Storage Physical 146
- Mass Storage controller 147
- Mass Storage Summary 148
- Environment Monitoring Unit 148
- External Expansion Cabinet 149
- Support and other resources 150
- HP authorized resellers 151
- Documentation feedback 151
- Related information 151
- Typographic conventions 151
- A Troubleshooting 153
- Known browser issues 154
- SNMP community string issues 155
- Insight Manager issues 156
- Missing NIC information 157
- 158 Troubleshooting 158
- Other problems 159
- 160 Troubleshooting 160
- Glossary 162
- 164 Index 164
Related products and manuals for Software Hp Insight Management Agents
Software Hp SmartStart-Software User Manual
(59 pages)
(59 pages)
(37 pages)
(120 pages)© 2020, manymanuals.com. All rights reserved. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals