HP 445942-001 User Manual Page 197
- Page / 199
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Maintenance Commands
197
Panic command
The panic command causes the switch to dump state information immediately to flash memory and
reboot.
To select panic, at the prompt, enter:
>> Switch# debug panic
A FLASH dump already exists.
Confirm replacing existing dump and reboot [y/n]:
Enter y to confirm the command:
Confirm dump and reboot [y/n]: y
A list of messages is displayed:
Starting system dump...done.
Reboot at 11:54:08 Wednesday March 14, 2007...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rebooted because of console PANIC command.
Booting complete
Unscheduled system dumps
If there is an unscheduled system dump to flash memory, the following message is displayed when you
log on to the switch:
Note: A system dump exists in FLASH. The dump was saved
at 13:43:22 Wednesday March 14, 2007.
Use show flash-dump uuencode to
extract the dump for analysis and clear flash-dump to
clear the FLASH region. The region must be cleared
before another dump can be saved.
- HP 10Gb Ethernet BL-c Switch 1
- Contents 3
- ISCLI reference 9
- Setting an IP address 10
- • Encryption: 11
- • Key Exchange—RSA 11
- Accessing the switch 12
- Idle timeout 13
- Typographical conventions 14
- ISCLI basics 15
- Global commands 17
- Command abbreviation 18
- Tab completion 18
- Information Commands 19
- System Information commands 20
- SNMPv3 Information commands 21
- • the user name 22
- • the privacy protocol 22
- SNMPv3 dump 27
- System information 28
- Show recent syslog messages 29
- System user information 30
- Layer 2 information 31
- FDB information commands 32
- Show all FDB information 33
- LACP dump 34
- 802.1x information 35
- Spanning Tree information 37
- Trunk group information 43
- VLAN information 44
- Layer 3 information 45
- Route information 46
- ARP information 48
- OSPF information 49
- OSPF general information 50
- OSPF interface information 50
- OSPF Database information 51
- OSPF route codes information 52
- RIP Routes information 53
- RIP user configuration 53
- IP information 54
- IGMP group information 55
- VRRP information 57
- 802.1p information 58
- ACL information 59
- RMON Information 60
- RMON alarm information 61
- RMON event information 62
- Link status information 63
- Port information 64
- Fiber Port SFP status 65
- Information dump 66
- Statistics Commands 67
- Port Statistics 68
- 802.1x statistics 69
- Bridging statistics 71
- Ethernet statistics 72
- Interface statistics 74
- Link statistics 76
- Layer 2 statistics 77
- LACP statistics 78
- Layer 3 statistics 79
- IP statistics 80
- Route statistics 81
- ARP statistics 82
- DNS statistics 82
- ICMP statistics 83
- TCP statistics 84
- UDP statistics 86
- OSPF statistics 87
- OSPF global statistics 88
- VRRP statistics 91
- RIP statistics 92
- GEA Layer 3 statistics 92
- Packet statistics 93
- CPU statistics 95
- ACL statistics 95
- SNMP statistics 96
- NTP statistics 98
- Statistics dump 100
- Configuration Commands 101
- System configuration 102
- RADIUS server configuration 106
- TACACS+ server configuration 107
- NTP server configuration 109
- System SNMP configuration 110
- SNMPv3 configuration 111
- SNMPv3 View configuration 114
- SNMPv3 Group configuration 115
- System Access configuration 119
- User ID configuration 120
- HTTPS Access configuration 122
- Port configuration 123
- Temporarily disabling a port 124
- Port link configuration 124
- ACL Port configuration 125
- Layer 2 configuration 126
- 802.1x Global configuration 127
- 802.1x Port configuration 128
- CIST bridge configuration 131
- CIST port configuration 132
- Spanning Tree configuration 134
- • Bridge priority 135
- • Bridge hello time 135
- • Bridge maximum age 135
- • Forwarding delay 135
- • 2*(fwd-1) ≥ mxage 136
- • 2*(hello+1) ≤ mxage 136
- • Port priority 136
- • Port path cost 136
- Static FDB configuration 137
- Trunk configuration 138
- LACP Port configuration 140
- VLAN configuration 141
- Layer 3 configuration 142
- Static ARP configuration 145
- IP Forwarding configuration 146
- Network Filter configuration 146
- Route Map configuration 147
- RIP Interface configuration 149
- IGMP configuration 157
- IGMP filtering configuration 160
- IGMP filter definition 161
- VRRP Tracking configuration 168
- QoS 802.1p configuration 170
- ACL Metering configuration 174
- ACL Re-mark configuration 175
- ACL Group configuration 177
- RMON history configuration 178
- RMON event configuration 179
- RMON alarm configuration 180
- Port mirroring 181
- Port-based port mirroring 182
- Configuration Dump 184
- Operations Commands 186
- Boot Options 188
- Resetting the switch 191
- Maintenance Commands 192
- Debugging options 193
- ARP cache maintenance 194
- IGMP Snooping maintenance 194
- IGMP Mrouter maintenance 195
- Uuencode flash dump 195
- FTP/TFTP system dump put 196
- Clearing dump information 196
- Unscheduled system dumps 197
Related products and manuals for Network switches HP 445942-001
Network switches HP AA-RS2JA-TE User Manual
(360 pages)
(360 pages)
Network switches HP P4459A User Manual
(72 pages)
(72 pages)
Network switches HP Switch 2510 User Manual
(40 pages)
(40 pages)
Network switches HP CN1000E User Manual
(29 pages)
(29 pages)
Network switches HP GBE2 User Manual
(176 pages)
(176 pages)
Network switches HP J3177A User Manual
(62 pages)
(62 pages)
Network switches HP 445946-001 User Manual
(198 pages)
(198 pages)
Network switches HP 1410-24G User Manual
(33 pages)
(33 pages)
Network switches HP MSR2000 User's Guide
(9 pages)
(9 pages)
Network switches HP 2600-PWR User Manual
(306 pages)
(306 pages)
Network switches HP 2000fc User Manual
(26 pages)
(26 pages)
Network switches HP 4/32B SAN User Manual
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 1.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals