HP 640n User's Guide Page 60
- Page / 228
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Table 3-3 Telnet Commands and Parameters (continued)
allow Add an entry into the host access list stored on the HP Jetdirect print server. Each entry
specifies a host or network of hosts allowed to connect to the printer. The format is
allow netnum [mask] where netnum is a network number or host IP address, and
mask is an address mask of bits applied to the network number and host address to
verify access. Add up to 10 access list entries. If there are no entries, all hosts are
permitted access. The following are some example settings:
allow 192.0.0.0 255.0.0.0 Allows hosts on network 192.
allow 192.168.1.2 Allow a single host. The default mask 255.255.255.255 is
assumed and is not required.
allow 0 Clear the host access list.
For additional information, see
Security features (V.45.xx.nn.xx) on page 121.
TCP/IP Other
syslog-config Allow syslog server operation on the print server (UDP port 514).
0: Disable.
1 (default): Enable.
syslog-svr
IPv4 address of the server that the HP Jetdirect server sends syslog messages to. For
example:
syslog-svr: 192.168.40.1
syslog-max
Maximum number of syslog messages the HP Jetdirect print server can send per
minute.
0: Disable. The number of syslog messages is not restricted.
10 (default): Enable.
syslog-priority
Filter syslog messages sent to the syslog server. The filter range is from 0 to 7, with 0
being the most specific and 7 the most general. Only messages that are lower than the
specified filter level (or higher in priority) are reported.
Set to 8 to disable all syslog messages.
0: Disable.
7 (default): Enable. Messages of all priorities are sent.
syslog-facility
Identify the source facility of a message. Typically used to identify the source of selected
messages during troubleshooting. By default, the HP Jetdirect print server uses LPR as
the source facility code. Use values of local0 through local7 to isolate individual or
groups of print servers.
slp-config Use the SLP operation on the print server. SLP is used by selected HP software
applications (through UDP port 427) to automate device discovery.
0: Disable.
1 (default): Enable.
If SLP uses multicast protocols, you must enable multicast IPv4.
50 Chapter 3 TCP/IP configuration ENWW
- HP Jetdirect Print Servers 1
- Table of contents 5
- Supported print servers 11
- Supported network protocols 12
- Security protocols 13
- Supplied manuals 14
- HP support 15
- Product registration 16
- Product accessibility 16
- Table 2-1 Software Solutions 17
- HP Web Jetadmin 19
- Configure and modify a device 20
- Microsoft-supplied software 21
- Mac OS network installation 22
- Verify network configuration 23
- Test the configuration 23
- 3 TCP/IP configuration 25
- IPv6 address configuration 26
- Stateless addresses 27
- Stateful addresses 27
- IPv4 configuration 28
- Default IP address (IPv4) 29
- Default IPv4 behavior 31
- TCP/IP configuration tools 31
- Use BOOTP/TFTP (IPv4) 32
- ENWW IPv4 configuration 27 37
- ENWW IPv4 configuration 29 39
- ENWW IPv4 configuration 31 41
- ENWW IPv4 configuration 33 43
- ENWW IPv4 configuration 35 45
- Use DHCP (IPv4) 46
- Use RARP (IPv4) 47
- Use Telnet (IPv4) 49
- Create a Telnet connection 50
- A typical Telnet session 50
- Telnet user interface options 51
- ENWW IPv4 configuration 43 53
- ENWW IPv4 configuration 45 55
- ENWW IPv4 configuration 47 57
- ENWW IPv4 configuration 49 59
- ENWW IPv4 configuration 51 61
- ENWW IPv4 configuration 53 63
- ENWW IPv4 configuration 55 65
- ENWW IPv4 configuration 57 67
- Main Menu 70
- Use the printer control panel 71
- 4 HP Embedded Web Server (V 73
- Requirements 74
- HP Jetdirect Home tab 76
- Networking tab 77
- Wireless Station 78
- ENWW Networking tab 69 79
- ENWW Networking tab 71 81
- ENWW Networking tab 73 83
- TCP/IP Settings 84
- Network Identification tab 85
- TCP/IP(v4) tab 86
- TCP/IP(v6) tab 87
- Config Precedence tab 88
- Advanced tab 89
- Network Settings 91
- AppleTalk 92
- Table 4-12 SNMP tab settings 94
- Other Settings 95
- Firmware Upgrade 97
- LPD Queues 97
- Select Language 100
- Security: Settings 100
- ENWW Networking tab 91 101
- Restore Defaults 102
- Authorization 103
- Configure certificates 104
- ENWW Networking tab 95 105
- Access Control 107
- Mgmt. Protocols 108
- Table 4-17 Other protocols 109
- 802.1X Authentication 110
- Table 4-18 802.1X 111
- ENWW Networking tab 101 111
- IPsec/Firewall 112
- Device Announcement Agent 112
- Other Links 113
- 45.xx.nn.xx) 115
- Figure 5-2 IPsec Policy page 116
- ENWW 107 117
- Default Rule example 118
- IPsec/Firewall Rules 119
- Create Address Template 120
- Create Service Template 121
- Manage Services 122
- Manage Custom Services 122
- Step 3: Specify Action 123
- Kerberos 125
- Table 5-9 Kerberos page 126
- Table 5-15 Manual Keys page 129
- Rule Summary 130
- ENWW 123 133
- Table 6-2 134
- Reset to factory defaults 136
- General troubleshooting 139
- Firmware download failure 147
- Status field error messages 150
- Configuration page format 150
- Configuration page messages 151
- Security Settings 154
- Network Statistics 156
- TCP/IP protocol information 157
- Table 8-7 IPv4 Section 158
- IPv6 section 159
- IPX/SPX protocol information 160
- Novell/NetWare parameters 161
- Error messages 162
- Table 8-13 Error messages 163
- HP Jetdirect Security page 169
- Security settings 170
- IPsec Error Log 172
- Local IP addresses 172
- IPsec Statistics 172
- IKE Stats 173
- IPsec Rules 173
- Available Network Services 174
- A LPD printing 175
- About LPD 176
- LPD setup overview 177
- LPD on UNIX systems 178
- Print a test file 180
- Install TCP/IP software 181
- Verify the configuration 182
- Add a new LPD printer 183
- B FTP printing 185
- FTP login 186
- End the FTP session 187
- Commands 187
- Example FTP Session 188
- Graphical control panel menus 190
- Expat XML Parser 204
- GNU General Public License 206
- OpenSSL license 218
- Original SSLeay license 218
- 216 Index ENWW 226
Related products and manuals for Networking HP 640n
Networking HP 3Com User Manual
(30 pages)
(30 pages)
Networking HP N1200-320 User Manual
(132 pages)
(132 pages)
Networking HP 2700W User Manual
(5 pages)
(5 pages)
Networking HP 706C User Manual
(123 pages)
(123 pages)
Networking HP ACC2 Aurora User Manual
(33 pages)
(33 pages)
Networking HP 720 Series User's Guide
(204 pages)
(204 pages)
(82 pages)
Networking HP X09 Manual
(56 pages)
(56 pages)
© 2020, manymanuals.com. All rights reserved. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals