HP 640n User's Guide Page 31
- Page / 228
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Default IPv4 behavior
When turned on, a factory-default print server connected to a network through a cable (wired),
retrieves its IPv4 settings by systematically using BOOTP, DHCP, and RARP. This can take several
minutes to complete. If configuration fails, a default IPv4 address is assigned.
Configuration tools that require a specific default IP address on the print server for initial
communication might not function without modification. To view the default IP address settings on the
print server, use the HP Jetdirect configuration page.
TCP/IP configuration tools
When a network connection is established, you can configure an HP Jetdirect print server with valid
TCP/IP parameters for your network, using the following methods:
● Software solutions Use installation, setup, and management software running on supported
systems. For more information see
HP software solutions summary on page 7.
● BOOTP/TFTP Download the data from a network-based server by using BOOTP and TFTP
each time the printer is turned on. For more information, see “
Use BOOTP/TFTP (IPv4)
on page 22”.
The BOOTP daemon (bootpd) must be running on a BOOTP server that is accessible by the
printer.
●
DHCP/TFTP Use DHCP and TFTP each time the printer is turned on. These protocols are
supported on HP-UX, Solaris, Linux, Microsoft Windows Server 2003, Windows Server 2008,
NetWare, and Mac OS systems. (See your network operating system manuals to verify that your
server supports DHCP.) For more information, see
Use DHCP (IPv4) on page 36.
NOTE: For more information about Linux and UNIX systems, see the bootpd man page.
On HP-UX systems, a sample DHCP configuration file (dhcptab) might be located in the /etc
directory.
Because HP-UX does not currently provide dynamic domain name system (DDNS) services for
its DHCP implementations, HP recommends that you set all print server lease durations to
infinite. This ensures that print server IP addresses remain static until DDNS is provided.
●
RARP Use RARP to answer the print server's RARP request and supply the print server with the
IP address. The RARP method allows you to only configure the IP address. For more
information, see “
Use RARP (IPv4) on page 37”.
●
arp and ping commands (Only for print servers configured with Legacy default IP address
192.0.0.192) Use the arp and ping commands from your system. For more information, see
“
Use the arp and ping commands (IPv4) on page 38”.
●
Telnet Set configuration parameters by creating a Telnet connection from your system to the
HP Jetdirect print server, using the default IP address. Once configured, the print server saves
the configuration when turned off and then turned on. For more information, see “
Use Telnet
(IPv4) on page 39”.
● HP Embedded Web Server Use the HP Embedded Web Server on the HP Jetdirect print server
to set configuration parameters. For more information, see
HP Embedded Web Server (V.
45.xx.nn.xx) on page 63.
●
Printer control panel (For printers that support HP Jetdirect control panel menus.) Manually
enter the configuration data, using the printer control panel keys. Because you can configure a
ENWW IPv4 configuration 21
- HP Jetdirect Print Servers 1
- Table of contents 5
- Supported print servers 11
- Supported network protocols 12
- Security protocols 13
- Supplied manuals 14
- HP support 15
- Product registration 16
- Product accessibility 16
- Table 2-1 Software Solutions 17
- HP Web Jetadmin 19
- Configure and modify a device 20
- Microsoft-supplied software 21
- Mac OS network installation 22
- Verify network configuration 23
- Test the configuration 23
- 3 TCP/IP configuration 25
- IPv6 address configuration 26
- Stateless addresses 27
- Stateful addresses 27
- IPv4 configuration 28
- Default IP address (IPv4) 29
- Default IPv4 behavior 31
- TCP/IP configuration tools 31
- Use BOOTP/TFTP (IPv4) 32
- ENWW IPv4 configuration 27 37
- ENWW IPv4 configuration 29 39
- ENWW IPv4 configuration 31 41
- ENWW IPv4 configuration 33 43
- ENWW IPv4 configuration 35 45
- Use DHCP (IPv4) 46
- Use RARP (IPv4) 47
- Use Telnet (IPv4) 49
- Create a Telnet connection 50
- A typical Telnet session 50
- Telnet user interface options 51
- ENWW IPv4 configuration 43 53
- ENWW IPv4 configuration 45 55
- ENWW IPv4 configuration 47 57
- ENWW IPv4 configuration 49 59
- ENWW IPv4 configuration 51 61
- ENWW IPv4 configuration 53 63
- ENWW IPv4 configuration 55 65
- ENWW IPv4 configuration 57 67
- Main Menu 70
- Use the printer control panel 71
- 4 HP Embedded Web Server (V 73
- Requirements 74
- HP Jetdirect Home tab 76
- Networking tab 77
- Wireless Station 78
- ENWW Networking tab 69 79
- ENWW Networking tab 71 81
- ENWW Networking tab 73 83
- TCP/IP Settings 84
- Network Identification tab 85
- TCP/IP(v4) tab 86
- TCP/IP(v6) tab 87
- Config Precedence tab 88
- Advanced tab 89
- Network Settings 91
- AppleTalk 92
- Table 4-12 SNMP tab settings 94
- Other Settings 95
- Firmware Upgrade 97
- LPD Queues 97
- Select Language 100
- Security: Settings 100
- ENWW Networking tab 91 101
- Restore Defaults 102
- Authorization 103
- Configure certificates 104
- ENWW Networking tab 95 105
- Access Control 107
- Mgmt. Protocols 108
- Table 4-17 Other protocols 109
- 802.1X Authentication 110
- Table 4-18 802.1X 111
- ENWW Networking tab 101 111
- IPsec/Firewall 112
- Device Announcement Agent 112
- Other Links 113
- 45.xx.nn.xx) 115
- Figure 5-2 IPsec Policy page 116
- ENWW 107 117
- Default Rule example 118
- IPsec/Firewall Rules 119
- Create Address Template 120
- Create Service Template 121
- Manage Services 122
- Manage Custom Services 122
- Step 3: Specify Action 123
- Kerberos 125
- Table 5-9 Kerberos page 126
- Table 5-15 Manual Keys page 129
- Rule Summary 130
- ENWW 123 133
- Table 6-2 134
- Reset to factory defaults 136
- General troubleshooting 139
- Firmware download failure 147
- Status field error messages 150
- Configuration page format 150
- Configuration page messages 151
- Security Settings 154
- Network Statistics 156
- TCP/IP protocol information 157
- Table 8-7 IPv4 Section 158
- IPv6 section 159
- IPX/SPX protocol information 160
- Novell/NetWare parameters 161
- Error messages 162
- Table 8-13 Error messages 163
- HP Jetdirect Security page 169
- Security settings 170
- IPsec Error Log 172
- Local IP addresses 172
- IPsec Statistics 172
- IKE Stats 173
- IPsec Rules 173
- Available Network Services 174
- A LPD printing 175
- About LPD 176
- LPD setup overview 177
- LPD on UNIX systems 178
- Print a test file 180
- Install TCP/IP software 181
- Verify the configuration 182
- Add a new LPD printer 183
- B FTP printing 185
- FTP login 186
- End the FTP session 187
- Commands 187
- Example FTP Session 188
- Graphical control panel menus 190
- Expat XML Parser 204
- GNU General Public License 206
- OpenSSL license 218
- Original SSLeay license 218
- 216 Index ENWW 226
Related products and manuals for Networking HP 640n
Networking HP 3Com User Manual
(30 pages)
(30 pages)
Networking HP N1200-320 User Manual
(132 pages)
(132 pages)
Networking HP 2700W User Manual
(5 pages)
(5 pages)
Networking HP 706C User Manual
(123 pages)
(123 pages)
Networking HP ACC2 Aurora User Manual
(33 pages)
(33 pages)
Networking HP 720 Series User's Guide
(204 pages)
(204 pages)
(82 pages)
Networking HP X09 Manual
(56 pages)
(56 pages)
© 2020, manymanuals.com. All rights reserved. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals