Hp C737990900 User Manual Page 139
- Page / 174
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Commands 139
Commands
3B 00h
Sequential positioning error A command has failed and left the logical position at an
unexpected location.
3D 00h
Invalid bits in Identify message An illegal Identify message has been received by the
drive at the start of a command.
3E 00h
Logical unit has not self-configured yet The drive has just powered on and has not completed its
self-test sequence, so it cannot process commands.
3F 01h
Microcode download The firmware in the drive has just been changed by a
WRITE BUFFER command.
3F 0Fh
Echo buffer overrun A Read Buffer command has been received with Echo
Buffer mode set, and the echo buffer has been overwritten
by a different host from that which issued the Read Buffer
command.
3F 11h
Media Auxiliary Memory accessible MAM is accessible but the cartridge is in the Hold
position. Unit Attention is generated.
40
XX
h
Diagnostic failure on component XX A diagnostic test has failed. The Additional Sense Code
Qualifier is a vendor-specific code indicating the failing
component.
43 00h
Message error A message could not be sent or received because of
excessive transmission errors.
44 00h
Internal target failure A hardware failure has been detected in the drive that
has caused the command to fail.
45 00h
Select or reselect failure An attempt to reselect an initiator in order to complete the
command has failed.
47 00h
SCSI parity error A command failed because of an excessive number of
parity errors on the SCSI interface.
48 00h
Initiator detected error message received A command failed because an Initiator Detected Error
message was received.
49 00h
Invalid message error The command failed because an invalid message was
received by the drive.
4A 00h
Command phase error A command could not be executed because too many
parity errors occurred in the command phase
4B 00h
Data phase error A command could not be completed because too many
errors occurred during the data phase.
4E 00h
Overlapped commands attempted An initiator selected the drive even though it already had
a command outstanding.
50 00h
Write append error A write-type command failed because the point at which
to append data was unreadable.
51 00h
Erase failure An
ERASE command failed to erase the required area on
the tape.
52 00h
Cartridge fault A command could not be completed because of a fault in
the tape cartridge.
53 00h
Media load or eject failed An attempt to load or eject the tape failed because of a
problem with the tape.
Code Description Explanation
- Edition 4, February 2003 1
- Revision History 2
- The Purpose of this Manual 3
- Related Documents 3
- Documentation Map 4
- Cartridges 5
- Interface 5
- Dealing with Errors 6
- Ultrium Features 6
- 1 Interface Implementation 13 9
- 2 Messages 25 10
- 3 Commands—Introduction 31 10
- 4 Commands 41 10
- Contents 11 11
- Glossary 165 12
- Index 169 12
- Interface Implementation 13
- Supported Messages 14
- Supported Commands 14
- SCSI Features 15
- Abort Handling 16
- Multi-Initiator Support 19
- Fibre Channel Operation 20
- Addresses 21
- Implications for Libraries 22
- Field Replaceable Units 23
- Messages 25
- 26 Messages 26
- Name Code Support 26
- Extended Message Support 27
- 30 Messages 30
- Commands—Introduction 31
- Command Details 32
- Pre-Execution Checks 32
- Deferred Error Check 33
- Diagnostic Status Check 33
- Fixed Bit Check 34
- Flag Link Check 34
- Illegal Command Check 34
- Illegal Field/Request Check 34
- Media Access Check 35
- Media Information Check 36
- Media Write Check 37
- Parameter List Check 37
- Reservation Check 37
- Command Descriptor Block 38
- CHECK CONDITION 39
- 40 Commands—Introduction 40
- ERASE 19h 42
- Erase Specific Status: 43
- INQUIRY 12h 44
- INQUIRY Data Pages 45
- Inquiry Data 46
- Inquiry Data Fields 47
- Vital Product Data Pages 49
- Unit Serial Number Page 50
- Device Identification Page 51
- Defined Identifiers 51
- Port Name (FC only) 52
- Device Name (FC only) 52
- Port Identifier (FC only) 53
- LOAD/UNLOAD 1Bh 55
- Load/Unload Specific Status: 56
- Loading a Cartridge 56
- Unloading a Cartridge 57
- LOCATE 2Bh 58
- Locate Specific Status: 59
- LOG SELECT 4Ch 60
- LOG SENSE 4Dh 62
- Log Page Format 63
- Supported Log Pages Page 64
- Write Error Counters Log Page 65
- Read Error Counters Log Page 66
- TapeAlert Log Page 67
- Tape Usage Log Page 69
- Tape Capacity Log Page 69
- Data Compression Log Page 70
- Performance Data Log Page 70
- MODE SELECT 15h/55h 72
- Mode Parameter Pages 74
- Mode Parameter Header 75
- 10-byte Header 76
- Header Fields 76
- Mode Block Descriptor 77
- Disconnect-Reconnect Page 79
- FC Drives 80
- Control Mode Page 81
- Control Mode Page Fields: 82
- Device Configuration Page 83
- Changeable Parameters: 84
- Unchangeable Parameters: 84
- Medium Partitions Mode Page 85
- (Partition Units) 86
- CHECK CONDITION with a sense 89
- -1 through -64 90
- MODE SENSE 1Ah/5Ah 91
- READ 08h 95
- GOOD status is returned 96
- Read Specific Status: 97
- READ ATTRIBUTE 8Ch 99
- CDB Fields: 100
- Commands 101
- MAM Attribute Data 103
- Attribute ID Values 104
- Medium Common Attributes 106
- Host Common Attributes 107
- Commands 109 109
- READ BLOCK LIMITS 05h 110
- READ BUFFER 3Ch 111
- Memory Sizes: 112
- Returned Data: 113
- READ POSITION 34h 115
- Returned Data Fields: 117
- Pre-Execution Checks: 119
- Command Descriptor Block: 119
- Specific Status: 119
- Data Returned 120
- RELEASE UNIT 17h/57h 121
- 10-Byte Only 122
- Release Unit Specific Status: 122
- REPORT DENSITY SUPPORT 44h 123
- Descriptor Blocks 124
- MODE SENSE command 125
- REPORT LUNS A0h 126
- REQUEST SENSE 03h 128
- Request Sense Data 129
- Returned Sense Data Fields: 130
- Sense Data Management 131
- Current Sense 132
- UNIT ATTENTION Sense 132
- DEFERRED ERROR Sense 133
- Write-Behind Deferred Errors: 134
- Bus Release Deferred Errors: 134
- Sense Keys 135
- Additional Sense Codes 136
- WRITE BUFFER command 139
- Error Codes 140
- RESERVE UNIT 16h/56h 141
- RELEASE UNIT command with 143
- REWIND 01h 144
- SEND DIAGNOSTIC 1Dh 145
- Data Required 146
- Specific Status 146
- Standard Self-Test 147
- SPACE 11h 148
- Space Specific Status: 149
- TEST UNIT READY 00h 151
- VERIFY 13h 152
- WRITE 0Ah 154
- Write Specific Status: 155
- Residue Information: 155
- WRITE ATTRIBUTE 8Dh 157
- Parameter List Format: 159
- WRITE BUFFER 3Bh 160
- Memory Sizes 162
- Commands 163 163
- WRITE FILEMARKS 10h 164
- Glossary 165
- 166 glossary 166
- 168 glossary 168
Related products and manuals for Hardware Hp C737990900
Hardware Hp XU800 User Manual
(140 pages)
(140 pages)
Hardware Hp HD1600 User Manual
(2 pages)
(2 pages)
Hardware Hp MSL6000 Series User Manual
(182 pages)
(182 pages)
Hardware Hp Wireless Device User Manual
(31 pages)
(31 pages)
Hardware Hp LTO 4 SAS User Manual
(46 pages)
(46 pages)
Hardware Hp ProLiant DL385 User Manual
(47 pages)
(47 pages)
Hardware Hp D2D120 User Manual
(20 pages)
(20 pages)
Hardware Hp 4250 User Manual
(4 pages)
(4 pages)
Hardware Hp MSL2024 User Manual
(4 pages)
(4 pages)
Hardware Hp 100TX NightDIRECTOR/100 User Manual
(121 pages)
(121 pages)
Hardware Hp 958-000290-000 User Manual
(144 pages)
(144 pages)
Hardware Hp mv2040 User Manual
(2 pages)
(2 pages)
Hardware Hp Fax 650 User Manual
(20 pages)
(20 pages)
Hardware Hp NAS 2000s User Manual
(20 pages)
(20 pages)
Hardware Hp NC1020 PCI 1000T User Manual
(6 pages)
(6 pages)
© 2020, manymanuals.com. All rights reserved. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals