HP StorageWorksCWDM MUX user guidePart number: AA-RWFAA-TEFirst edition: February 2008
10About this guide
1AboutHPCWDMMUXmodulesand CWDM (SFP) transceiversThis chapter includes information about:• “HP CWDM MUX modules”onpage11•“CWDM (SFP) transceivers”onpa
• One monitor port, a lso known as tap port, optionally used to connect optical monitoringequipment for checking optical link quality• One network por
gigabits of data from one location to another. Typical applications include linking two data centersto become one virtual site, mirroring two sites fo
Figure 5 Point -to -po in t: 4-por t (non-redundant)Figure 6 Point- to-point: 8-port to 4-port (non -redundant)Point-to-point redundant configurations
In Figure 7, Figure 8 and Figure 9, the HP CWDM MUX modules on the left ar e termed the West pathand the modules on the right are termed the East path
Figure 9 Point- to-point: 8-por t to 4-port to 4-por t (redundant, no single point offailure)CWDM (SFP) transceiversCWDM (SFP) transceivers are hot-sw
• Low power dissipationFor a list of specific CWDM (SFP) transceivers and part numbers, see the H Pwebsitewww.hp.com/go/cwdm-muxCWDM (SFP) transceivers
18About HP CWDM MUX modules and CWDM (SFP) transceivers
2 Installing HP CWDM MUXmodulesThe following hardware is required to install the HP CWDM MUX modules:• HP StorageWorks C WDM 2-slot chassis• HP Storag
Legal and notice information© Copyright 2008 Hewlett-Packard Development Company, L.P.The information contained herein is subject to change without no
• Avoid bringing synthetic m aterials such as polyester, plastic, vinyl, or styrofoam into the areawhere installation is being performed because these
• To clean contaminants from the optical bores of a CWDM (SFP) transceiver, use lint-free 1.25 m mFiber Optic swabs to clean the ferrules of the op ti
3. Slide the CWDM (SFP) transceiver out of the device module slot.NOTE:IfyourCWDM(SFP)transceiverdoesnotslideeasilyfromthemoduleslot,useagentleside-to
Figure13CablinganHPCWDMAdd/DropMUXModuleConnecting to the networkThere are two possible network config urations, using either t wo or three HP CWDM MUX
24Installing HP CWDM MUX modules
AHPCWDMMUXmodulesspec ificationsCWDM 8-port Multiplexer/Demultiplexer module specificationTable 3 HP Storag eWorks CWDM 8-port Multiplexe r /Demultiplex
CWDM Slot A 4-port Add/Drop Multiplexer and CWDM SlotB4-portAdd/Drop Multiplexer specificationsTable 4 CWDM Slot A 4-por t Add/Drop Multipl exer and CW
BFCCWarningStatementThis equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to Part 15 of the FCC Rul
ContentsAboutthisguide ... 7Intendedaudience... 7Relateddocumentation...
Figures1HPStorageWorksCWDM8-portMultiplexer/Demultiplexermodule ... 122HPStorageWorksCWDMSlotA4-portAdd/DropMultiplexer ... 123HPStora
Tables1 Documentconventions... 72HPCWDMMUXandCWDM(SFP)transceivercolorcodes... 223HP StorageWorks CWDM 8-port M
6
About this guideThis guide provides information about:• HP StorageWorks CWDM MUX (HP C WDM MUX) mod ule features and capabilities• CWDM Sm all Form Pl
WARNING!Indicates that failure to follow directions could result in bodily harm or death.CAUTION:Indicates that failure to follow directions could res
After registering, you will receive e-m ail notification of product enhancements, new driver versions,firmware updates, and other product resources.HP w
Comments to this Manuals