Hp 8.20q Fibre Channel Switch User Manual Page 22
- Page / 162
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
22 Installing, Upgrading, and Removing HP SAN Connection Manager
Linux installation: upgrade
Follow these steps to upgrade a previous installation of the required software on servers running Linux.
To upgrade the components required by SAN Connection Manager on Linux:
1. Insert the installation CD into the CD-ROM drive of the server.
The installation CD should mount automatically in one of the following locations:
/media/cdrom/
/mnt/cdrom/
/media/cdrecorder/
If the installation CD is not mounted automatically, issue the following commands to mount the CD:
# mkdir -p /mnt/cdrom
# mount /dev/cdrom /mnt/cdrom
IMPORTANT: Under specific distributions, such as RHEL 5, the installation CD is auto-mounted
using the following CD label:
# /media/HpInstallx.x/
If this occurs, the CD may get mounted with the no execution flag, causing the installation script
to fail. Installation failure may be indicated by the following error message:
# ./install_smb.sh
The following is returned:
bash: ./install_smb.sh: /bin/sh: bad interpreter: Permission denied
The workaround is to manually mount the installation CD. For example, if the CD was auto-mounted
in /media/HpInstallx.x, issue these commands to unmount, and then remount the CD:
# unmount /media/HpInstallx.x
# mkdir -p /mnt/cdrom
# mount /dev/cdrom /mnt/cdrom
If the unmount command fails with a busy warning, make sure that all applications and consoles
that could be using the CD media are closed, and then try again.
2. Change directory to the linux directory. For example, if the installation CD is mounted in
/mnt/cdrom, issue the command:
# cd /mnt/cdrom/HP_SSCM/linux/
3. Run the install_smb.sh script as follows:
# ./install_smb.sh
This will install the following components:
• QLogic FC HBA driver (only updated on RH4, Suse 9, and RH5.2)
• HP Array Configuration Utility
• QLogic SANsurfer agent, QLRemote (if possible, the installation program will also start the
SANsurfer agent, QLRemote)
- Part Number: 5697-1313 1
- Published January 2012 1
- Edition: 7 1
- Contents 3
- 1Introduction 9
- System requirements 10
- Connection Manager 11
- Windows installation: initial 12
- Linux installation: initial 15
- HP-UX configuration 17
- Emulex HBA configuration 17
- Windows installation: upgrade 18
- Linux installation: upgrade 22
- 3 Getting Started 27
- Menu bar 28
- Advanced Operations menu 29
- Help menu 30
- Using the help system 31
- 32 Getting Started 32
- 34 Getting Started 34
- 36 Getting Started 36
- 38 Getting Started 38
- 40 Getting Started 40
- Viewing a LUN Assignment map 42
- Viewing the event log 43
- Comparing configurations 45
- 5 Managing Switches 47
- Viewing network properties 48
- 50 Managing Switches 50
- 52 Managing Switches 52
- Setting the switch IP address 54
- Updating switch firmware 56
- 58 Managing Switches 58
- 60 Managing Switches 60
- Setting DNS properties 62
- Setting switch IP security 63
- Creating an IPsec association 64
- 66 Managing Switches 66
- Editing an IPsec association 67
- Deleting an IPsec association 67
- Managing security policies 68
- Creating an IPsec policy 69
- 70 Managing Switches 70
- Editing an IPsec policy 72
- Deleting an IPsec policy 73
- 74 Managing Switches 74
- 6 Managing HBAs 75
- Updating an HBA BIOS image 76
- Updating an HBA driver 78
- Creating an alias for an HBA 80
- 82 Managing HBAs 82
- 7 Managing Logical Disks 83
- 84 Managing Logical Disks 84
- 86 Managing Logical Disks 86
- 90 Managing Logical Disks 90
- 92 Managing Logical Disks 92
- 94 Managing Logical Disks 94
- 96 Managing Logical Disks 96
- Expanding a logical disk 97
- Deleting a logical disk 98
- 100 Managing Logical Disks 100
- 8 Managing Servers 101
- 102 Managing Servers 102
- Refreshing the server list 103
- 104 Managing Servers 104
- Manually creating a partition 106
- 108 Managing Servers 108
- Managing a partition 110
- 112 Managing Servers 112
- 114 Managing Servers 114
- Supported configurations 115
- Viewing VCEM information 115
- Viewing subsystem information 121
- Managing storage subsystems 122
- Updating software 126
- Prerequisites 139
- Contacting HP 140
- Subscription service 140
- Documentation feedback 140
- Related information 140
- Customer self repair 141
- ATroubleshooting 143
- 146 Troubleshooting 146
- 148 Troubleshooting 148
- Glossary 149
Related products and manuals for Storage Hp 8.20q Fibre Channel Switch
Storage Hp XP Array Manager Software User Manual
(128 pages)
(128 pages)
Storage Hp StoreAll Storage User Manual
(165 pages)
(165 pages)
Storage Hp Surestore 6164 Switch User Manual
(161 pages)
(161 pages)
Storage Hp XP Business Copy Software User Manual
(178 pages)
(178 pages)
Storage Hp StoreOnce Backup User Manual
(156 pages)
(156 pages)
Storage Hp PolyServe Software User Manual
(14 pages)
(14 pages)
Storage Hp Optical Jukeboxes User Manual
(77 pages)
(77 pages)
© 2020, manymanuals.com. All rights reserved. | 4.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals