Hp 8.20q Fibre Channel Switch User Manual Page 17
- Page / 162
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
HP SAN Connection Manager User Guide 17
6. To verify that the installation completed, check the FC HBA driver version:
a. To ensure that the driver is installed in the correct location, issue the following command:
# modinfo qla2xxx
The following is returned:
Filename: /lib/modules/2.6.9-55.ELsmp/kernel/drivers/scsi/qla2xxx/qla2xxx.ko
Version: 8.02.23 653675A771C3619AEEA4E9A
b. To verify that the driver is loaded, issue the following command:
# lsmod | grep qla2xxx
The following is returned:
qla2xxx_conf 303752 1
qla2xxx 982688 0
scsi_mod 445298 qla2xxx
c. To verify that the correct driver is loaded, issue the following command:
# cat /proc/scsi/qla2xxx/* | grep "Driver version"
The following is returned:
Firmware version: 3.03.25 IPX
Driver version: 8.02.23-fo
Configuring SAN Connection Manager for HP-UX and Emulex HBAs
SAN Connection Manager is compatible with the HP-UX operating system and Emulex HBAs when
configured as described in this section.
HP-UX configuration
SAN Connection Manager can manage all of your supported HP-UX servers. The HP-UX operating system
provides native software drivers for the HP FC HBAs. For the application to properly identify your server(s),
you must manually enter the FDMI information when the application prompts for it. For more information,
see “Manually entering FDMI information,” page 80.
Emulex HBA configuration
SAN Connection Manager can manage all of your supported Windows and Linux servers that have
Emulex HBAs installed. In order for the application to properly identify your server(s), you must set the
EnableFDMI parameter on the Emulex HBA. Use the HBAnyware software to set the EnableFDMI
parameter to a value of 2.
For detailed instructions on how to enable the FDMI parameter on your Emulex HBA, see your HBA
documentation.
If FDMI is not enabled on the HBA, SAN Connection Manager will prompt you to manually enter the FDMI
information. For more information, see “Manually entering FDMI information,” page 80.
Installing SAN Connection Manager: upgrade installation
Use the HP SAN Connection Manager CD to upgrade a previous installation of the management software
on your management station as described in “Windows installation: upgrade,” page 18. Then use the
same CD to upgrade the HBA driver and other required software on each of the other servers in your SAN.
Depending on the server operating system for the non-management station installations, refer to either the
steps for “Windows installation: upgrade,” page 18 or “Linux installation: upgrade,” page 22.
- Part Number: 5697-1313 1
- Published January 2012 1
- Edition: 7 1
- Contents 3
- 1Introduction 9
- System requirements 10
- Connection Manager 11
- Windows installation: initial 12
- Linux installation: initial 15
- HP-UX configuration 17
- Emulex HBA configuration 17
- Windows installation: upgrade 18
- Linux installation: upgrade 22
- 3 Getting Started 27
- Menu bar 28
- Advanced Operations menu 29
- Help menu 30
- Using the help system 31
- 32 Getting Started 32
- 34 Getting Started 34
- 36 Getting Started 36
- 38 Getting Started 38
- 40 Getting Started 40
- Viewing a LUN Assignment map 42
- Viewing the event log 43
- Comparing configurations 45
- 5 Managing Switches 47
- Viewing network properties 48
- 50 Managing Switches 50
- 52 Managing Switches 52
- Setting the switch IP address 54
- Updating switch firmware 56
- 58 Managing Switches 58
- 60 Managing Switches 60
- Setting DNS properties 62
- Setting switch IP security 63
- Creating an IPsec association 64
- 66 Managing Switches 66
- Editing an IPsec association 67
- Deleting an IPsec association 67
- Managing security policies 68
- Creating an IPsec policy 69
- 70 Managing Switches 70
- Editing an IPsec policy 72
- Deleting an IPsec policy 73
- 74 Managing Switches 74
- 6 Managing HBAs 75
- Updating an HBA BIOS image 76
- Updating an HBA driver 78
- Creating an alias for an HBA 80
- 82 Managing HBAs 82
- 7 Managing Logical Disks 83
- 84 Managing Logical Disks 84
- 86 Managing Logical Disks 86
- 90 Managing Logical Disks 90
- 92 Managing Logical Disks 92
- 94 Managing Logical Disks 94
- 96 Managing Logical Disks 96
- Expanding a logical disk 97
- Deleting a logical disk 98
- 100 Managing Logical Disks 100
- 8 Managing Servers 101
- 102 Managing Servers 102
- Refreshing the server list 103
- 104 Managing Servers 104
- Manually creating a partition 106
- 108 Managing Servers 108
- Managing a partition 110
- 112 Managing Servers 112
- 114 Managing Servers 114
- Supported configurations 115
- Viewing VCEM information 115
- Viewing subsystem information 121
- Managing storage subsystems 122
- Updating software 126
- Prerequisites 139
- Contacting HP 140
- Subscription service 140
- Documentation feedback 140
- Related information 140
- Customer self repair 141
- ATroubleshooting 143
- 146 Troubleshooting 146
- 148 Troubleshooting 148
- Glossary 149
Related products and manuals for Storage Hp 8.20q Fibre Channel Switch
Storage Hp XP Array Manager Software User Manual
(128 pages)
(128 pages)
Storage Hp StoreAll Storage User Manual
(165 pages)
(165 pages)
Storage Hp Surestore 6164 Switch User Manual
(161 pages)
(161 pages)
Storage Hp XP Business Copy Software User Manual
(178 pages)
(178 pages)
Storage Hp StoreOnce Backup User Manual
(156 pages)
(156 pages)
Storage Hp PolyServe Software User Manual
(14 pages)
(14 pages)
Storage Hp Optical Jukeboxes User Manual
(77 pages)
(77 pages)
© 2020, manymanuals.com. All rights reserved. | 1.670 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals