Hp ProLiant BL680c G5 Server-Blade User Manual Page 53
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Software and configuration utilities 53
Re-entering the server serial number and product ID
After you replace the system board, you must re-enter the server serial number and the product ID.
1. During the server startup sequence, press the F9 key to access RBSU.
2. Select the System Options menu.
3. Select Serial Number. The following warning is displayed:
WARNING! WARNING! WARNING! The serial number is loaded into the system
during the manufacturing process and should NOT be modified. This option
should only be used by qualified service personnel. This value should
always match the serial number sticker located on the chassis.
4. Press the Enter key to clear the warning.
5. Enter the serial number and press the Enter key.
6. Select Product ID.
7. Enter the product ID and press the Enter key.
8. Press the Esc key to close the menu.
9. Press the Esc key to exit RBSU.
10. Press the F10 key to confirm exiting RBSU. The server will automatically reboot.
Management tools
Automatic Server Recovery
ASR is a feature that causes the system to restart when a catastrophic operating system error occurs, such
as a blue screen, ABEND, or panic. A system fail-safe timer, the ASR timer, starts when the System
Management driver, also known as the Health Driver, is loaded. When the operating system is
functioning properly, the system periodically resets the timer. However, when the operating system fails,
the timer expires and restarts the server.
ASR increases server availability by restarting the server within a specified time after a system hang or
shutdown. At the same time, the HP SIM console notifies you by sending a message to a designated
pager number that ASR has restarted the system. You can disable ASR from the HP SIM console or
through RBSU.
ROMPaq utility
The ROMPaq utility enables you to upgrade the system firmware (BIOS) or Lights-Out 100 firmware. To
upgrade the firmware, insert a ROMPaq diskette into the diskette drive or ROMPaq USB Key into an
available USB port and boot the system.
The ROMPaq utility checks the system and provides a choice (if more than one exists) of available
firmware revisions.
For more information about the ROMPaq utility, see the HP website (http://www.hp.com/go/support
).
- User Guide 1
- Audience assumptions 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs 7
- SAS and SATA hard drive LEDs 8
- System board components 9
- FBDIMM slots 10
- System maintenance switch 10
- Accessing the redundant ROM 11
- Local I/O cable 12
- Operations 13
- Remove the server blade 14
- Remove the access panel 14
- Install the access panel 15
- Remove the FBDIMM baffle 15
- Install the FBDIMM baffle 16
- Operations 17 17
- Overview 18
- Installing a server blade 19
- Setup 20 20
- 1. Remove the blank 20
- Setup 21 21
- Remove the connector covers 22
- Connecting to the network 23
- Completing the configuration 23
- Introduction 24
- Processor option 25
- 8. Install the processor 27
- Memory option 28
- Memory configurations 29
- Installing FBDIMMs 32
- Mezzanine card option 33
- Install the cache module 36
- Cabling 38
- Array controller cabling 40
- Cabling 41 41
- Network-based PXE deployment 43
- Deployment infrastructure 44
- Deployment methods 45
- CD-ROM deployment 46
- Diskette image deployment 47
- Configuration tools 48
- HP ROM-Based Setup Utility 49
- Auto-configuration process 50
- Boot options 50
- BIOS Serial Console 51
- Configuring mirrored memory 51
- Array Configuration Utility 52
- Management tools 53
- Erase Utility 54
- HP Systems Insight Manager 54
- Management Agents 55
- ProLiant Edition 55
- Redundant ROM support 56
- Diagnostic tools 57
- Integrated Management Log 58
- Array Diagnostic Utility 58
- Keeping the system current 59
- ProLiant Support Packs 60
- Care Pack 60
- Battery replacement 61
- Troubleshooting 62
- Symbols on equipment 63
- Warnings 63
- Symptom information 64
- Service notifications 65
- Loose connections 65
- Troubleshooting flowcharts 65
- Start diagnosis flowchart 66
- General diagnosis flowchart 67
- Symptoms: 69
- POST problems flowchart 71
- Item Refer to 72
- OS boot problems flowchart 73
- • Corrupted OS 74
- • Redundancy failure 76
- Troubleshooting 77 77
- FCC rating label 78
- Class A equipment 78
- Class B equipment 78
- Modifications 79
- • EMC Directive 2004/108/EC 80
- Japanese notice 81
- BSMI notice 81
- Korean notice 82
- Battery replacement notice 82
- Electrostatic discharge 84
- Specifications 85
- Technical support 86
- Technical support 87 87
- Customer Self Repair 88
- Technical support 89 89
- Reparo feito pelo cliente 90
- Technical support 91 91
- Technical support 92 92
- Technical support 93 93
- Acronyms and abbreviations 94
- Web-Based Enterprise Service 97
- Wired for Management 97
- Index 98 98
- Index 99 99
- Index 100 100
Related products and manuals for Computer hardware Hp ProLiant BL680c G5 Server-Blade
(114 pages)© 2020, manymanuals.com. All rights reserved. | 5.980 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals