Hp ProLiant BL680c G5 Server-Blade User Manual Page 50
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Software and configuration utilities 50
IMPORTANT: RBSU automatically saves settings when you press the Enter key. The utility does
not prompt you for confirmation of settings before you exit the utility. To change a selected
setting, you must select a different setting and press the Enter key.
Default configuration settings are applied to the server at one of the following times:
• Upon the first system power-up
• After defaults have been restored
Default configuration settings are sufficient for proper typical server operation, but configuration settings
can be modified using RBSU. The system will prompt you for access to RBSU with each power-up.
Auto-configuration process
The auto-configuration process automatically runs when you boot the server for the first time. During the
power-up sequence, the system ROM automatically configures the entire system without needing any
intervention. During this process, the ORCA utility, in most cases, automatically configures the array to a
default setting based on the number of drives connected to the server.
NOTE: The server may not support all the following examples.
NOTE: If the boot drive is not empty or has been written to in the past, ORCA does not
automatically configure the array. You must run ORCA to configure the array settings.
Drives installed Drives used RAID level
1 1 RAID 0
2 2 RAID 1
3, 4, 5, or 6 3, 4, 5, or 6 RAID 5
More than 6 0 None
To change any ORCA default settings and override the auto-configuration process, press the F8 key when
prompted.
By default, the auto-configuration process configures the system for the English language. To change any
default settings in the auto-configuration process (such as the settings for language, operating system, and
primary boot controller), execute RBSU by pressing the F9 key when prompted. After the settings are
selected, exit RBSU and allow the server to reboot automatically.
For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD
or the HP website (http://www.hp.com/support/smartstart/documentation
).
Boot options
Near the end of the boot process, the boot options screen is displayed. This screen is visible for several
seconds before the system attempts to boot from a diskette, CD, or hard drive. During this time, you can
do the following:
• Access RBSU by pressing the F9 key
• Access the System Maintenance Menu (which enables you to launch ROM-based Diagnostics or
Inspect) by pressing the F10 key
- User Guide 1
- Audience assumptions 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs 7
- SAS and SATA hard drive LEDs 8
- System board components 9
- FBDIMM slots 10
- System maintenance switch 10
- Accessing the redundant ROM 11
- Local I/O cable 12
- Operations 13
- Remove the server blade 14
- Remove the access panel 14
- Install the access panel 15
- Remove the FBDIMM baffle 15
- Install the FBDIMM baffle 16
- Operations 17 17
- Overview 18
- Installing a server blade 19
- Setup 20 20
- 1. Remove the blank 20
- Setup 21 21
- Remove the connector covers 22
- Connecting to the network 23
- Completing the configuration 23
- Introduction 24
- Processor option 25
- 8. Install the processor 27
- Memory option 28
- Memory configurations 29
- Installing FBDIMMs 32
- Mezzanine card option 33
- Install the cache module 36
- Cabling 38
- Array controller cabling 40
- Cabling 41 41
- Network-based PXE deployment 43
- Deployment infrastructure 44
- Deployment methods 45
- CD-ROM deployment 46
- Diskette image deployment 47
- Configuration tools 48
- HP ROM-Based Setup Utility 49
- Auto-configuration process 50
- Boot options 50
- BIOS Serial Console 51
- Configuring mirrored memory 51
- Array Configuration Utility 52
- Management tools 53
- Erase Utility 54
- HP Systems Insight Manager 54
- Management Agents 55
- ProLiant Edition 55
- Redundant ROM support 56
- Diagnostic tools 57
- Integrated Management Log 58
- Array Diagnostic Utility 58
- Keeping the system current 59
- ProLiant Support Packs 60
- Care Pack 60
- Battery replacement 61
- Troubleshooting 62
- Symbols on equipment 63
- Warnings 63
- Symptom information 64
- Service notifications 65
- Loose connections 65
- Troubleshooting flowcharts 65
- Start diagnosis flowchart 66
- General diagnosis flowchart 67
- Symptoms: 69
- POST problems flowchart 71
- Item Refer to 72
- OS boot problems flowchart 73
- • Corrupted OS 74
- • Redundancy failure 76
- Troubleshooting 77 77
- FCC rating label 78
- Class A equipment 78
- Class B equipment 78
- Modifications 79
- • EMC Directive 2004/108/EC 80
- Japanese notice 81
- BSMI notice 81
- Korean notice 82
- Battery replacement notice 82
- Electrostatic discharge 84
- Specifications 85
- Technical support 86
- Technical support 87 87
- Customer Self Repair 88
- Technical support 89 89
- Reparo feito pelo cliente 90
- Technical support 91 91
- Technical support 92 92
- Technical support 93 93
- Acronyms and abbreviations 94
- Web-Based Enterprise Service 97
- Wired for Management 97
- Index 98 98
- Index 99 99
- Index 100 100
Related products and manuals for Computer hardware Hp ProLiant BL680c G5 Server-Blade
(114 pages)© 2020, manymanuals.com. All rights reserved. | 3.881 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals