Hp ProLiant BL680c G5 Server-Blade User Manual Page 11
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Component identification 11
Position Function Default
4 Reserved Off
5* Password disabled Off
6* Reset configuration Off
7 Reserved Off
8 Reserved Off
*To access redundant ROM, set S1, S5, and S6 to ON.
System maintenance switch procedures
When you perform troubleshooting steps, this guide may instruct you to perform the following procedures:
• Clear the system configuration.
• Access the redundant ROM.
To complete these procedures, you must change physical settings on the system maintenance switch.
Clearing the system configuration
RBSU can be used to restore the factory default configuration. For more information, see "HP ROM-Based
Setup Utility (on page 49)." If the system is unable to boot into RBSU, use the following steps to clear the
system configuration:
1. Power down the server blade (on page 13).
2. Remove the server blade (on page 14).
3. Remove the access panel (on page 14).
4. Change position 6 of the system maintenance switch to on.
5. Install the access panel (on page 15).
6. Install the server blade in the enclosure and power up the server blade.
7. Wait for the POST message that prompts you to change the switch setting:
Maintenance switch detected in the "On" position.
Power off the server and turn switch to the "Off" position.
8. Repeat steps 1 through 3.
9. Change position 6 of the system maintenance switch to off.
10. Repeat steps 5 and 6.
IMPORTANT: When the server blade boots after NVRAM is cleared, a delay of up to 2
minutes is normal. During this delay, the system appears non-functional. Do not attempt any
procedures during the delay.
Accessing the redundant ROM
If the system ROM is corrupted, the system automatically switches to the redundant ROM in most cases. If
the system does not automatically switch to the redundant ROM, perform the following steps:
1. Power down the server blade (on page 13).
2. Remove the server blade (on page 14).
- User Guide 1
- Audience assumptions 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs 7
- SAS and SATA hard drive LEDs 8
- System board components 9
- FBDIMM slots 10
- System maintenance switch 10
- Accessing the redundant ROM 11
- Local I/O cable 12
- Operations 13
- Remove the server blade 14
- Remove the access panel 14
- Install the access panel 15
- Remove the FBDIMM baffle 15
- Install the FBDIMM baffle 16
- Operations 17 17
- Overview 18
- Installing a server blade 19
- Setup 20 20
- 1. Remove the blank 20
- Setup 21 21
- Remove the connector covers 22
- Connecting to the network 23
- Completing the configuration 23
- Introduction 24
- Processor option 25
- 8. Install the processor 27
- Memory option 28
- Memory configurations 29
- Installing FBDIMMs 32
- Mezzanine card option 33
- Install the cache module 36
- Cabling 38
- Array controller cabling 40
- Cabling 41 41
- Network-based PXE deployment 43
- Deployment infrastructure 44
- Deployment methods 45
- CD-ROM deployment 46
- Diskette image deployment 47
- Configuration tools 48
- HP ROM-Based Setup Utility 49
- Auto-configuration process 50
- Boot options 50
- BIOS Serial Console 51
- Configuring mirrored memory 51
- Array Configuration Utility 52
- Management tools 53
- Erase Utility 54
- HP Systems Insight Manager 54
- Management Agents 55
- ProLiant Edition 55
- Redundant ROM support 56
- Diagnostic tools 57
- Integrated Management Log 58
- Array Diagnostic Utility 58
- Keeping the system current 59
- ProLiant Support Packs 60
- Care Pack 60
- Battery replacement 61
- Troubleshooting 62
- Symbols on equipment 63
- Warnings 63
- Symptom information 64
- Service notifications 65
- Loose connections 65
- Troubleshooting flowcharts 65
- Start diagnosis flowchart 66
- General diagnosis flowchart 67
- Symptoms: 69
- POST problems flowchart 71
- Item Refer to 72
- OS boot problems flowchart 73
- • Corrupted OS 74
- • Redundancy failure 76
- Troubleshooting 77 77
- FCC rating label 78
- Class A equipment 78
- Class B equipment 78
- Modifications 79
- • EMC Directive 2004/108/EC 80
- Japanese notice 81
- BSMI notice 81
- Korean notice 82
- Battery replacement notice 82
- Electrostatic discharge 84
- Specifications 85
- Technical support 86
- Technical support 87 87
- Customer Self Repair 88
- Technical support 89 89
- Reparo feito pelo cliente 90
- Technical support 91 91
- Technical support 92 92
- Technical support 93 93
- Acronyms and abbreviations 94
- Web-Based Enterprise Service 97
- Wired for Management 97
- Index 98 98
- Index 99 99
- Index 100 100
Related products and manuals for Computer hardware Hp ProLiant BL680c G5 Server-Blade
(114 pages)© 2020, manymanuals.com. All rights reserved. | 2.523 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals