SCSI Hard Drive InstallationHP Workstation xw SeriesThis document describes how to install a SCSI hard drive into an HP Workstation xw series.Installi
10 7 は SCSI コント ローラ用に予約されています。 1 から 6 と 8 から 15 は、 その他のすべての SCSI デバ イ ス に使用可能です。プライマリ ハー ド ディスク ドライブに0 が使用 さ れてい る場合、 2 台目のハー ド ディスク ドライブには1、 3
114. ハー ド ディスク ドライブのレール アセンブ リ のピンを、 一方のハード ディスク ドライブのネジ穴に挿入してレールをハードディ ス ク ドライブに取り付けます。次に、ハード ディスク ドライブのレール アセンブ リ の反対側をゆっ く り と開き、 残り のピンをハード デ
12以下の図に、 SCSI ハー ド ディスク ドライブを取り付けたxw8200 を示し ます。 6. データ ケーブルをシステム ボード の SCSI コ ネ ク タ (ワー ク ス テーシ ョ ンの底面近 く を確認、 ま たは、 前の図を参照) に接続し ます。お使いのワー ク ス テーシ
13SCSI コントローラ カード1. ハー ド ディスク ドライブをまだインストールしていない場合は、「ハード ディスク ド ライブのイ ンス ト ール」 の手順に従い ド ラ イブを イ ン ス ト ールし ます。2. SCSI コント ローラ カー ド を使用可能な PCI 拡張ス ロ
14Windows XP でのパーテ ィ シ ョ ンの作成Microsoft® Windows® XP で新し い ド ラ イ ブにパーテ ィ シ ョ ン を作成する には、 以下の手順で行います。1. デス ク ト ップから [ スタート ] をク リ ックし、 [ コント ロール パネル ] を
155. [ ディスクの管理] をク リ ックします。 [Write Signature and Upgrade Disk] ウィザードが起動します。 [ キャンセル] をク リ ックし、 ウィザードを中止します。6. [Disk 1 Unallocated] の領域で右ク リ ッ ク し ます。
16パーテ ィ シ ョ ンの種類を選択する 前に、 Red Hat Linux (お使いの HP システムに、 おそら くインス トールされています) では、 1 台のデ ィ ス ク につき最大 4 つのプ ラ イ マ リ パーテ ィシ ョ ンが作成可能であ る こ と に注意し て く だ さ
171. シェル プロンプト を開き、 root ユーザー と し て ロ グ イ ン し ます。2.pico -w /etc/fstabと入力します。3. ラベルを割り当てたパーティシ ョ ンごとに、/etc/fstabに行を追加し ます。 /etc/fstabの入力の際に、 各/mount/po
18© 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. Microsoft
2To set the SCSI ID on a drive, see the instructions on top/back of the hard drive for the correct jumper settings. The drive probably displays a diag
35. Push the drive into the selected bay until it snaps into place. Then attach the power and data cable to the drive.NOTE: For an HP Workstation xw42
4SCSI Controller Card1. If you have not already done so, follow the applicable instructions for “Installing the Hard Drive.’’2. Insert the SCSI contro
5Creating a Partition Using Windows XPTo create a partition for the new drive using Microsoft® Windows® XP:1. From the desktop click Start, then click
69. Select the partition needed or use the defaults.10. Click Next.11. Specify the partition size or use the defaults.12. Click Next.13. Specify the d
76. Repeat this process until you have created your desired partitioning scheme.NOTE: By entering w, you are permanently destroying any data that curr
8Technical SupportPhone or Online Contact your local HP technical support provider. You can get additional information by visiting the HP Web site
SCSI ハー ド ディスク ドライブのインストールHP Workstation xw シリーズ本書では、 SCSI ハー ド ディスク ドライブをHP Workstation xw シリーズにインストールする方法を説明し ます。新しいハード ディスク ドライブのインストールÅ警告 : 表
Comments to this Manuals