Hp Storage Mirroring Software User Manual Page 332
- Page / 678
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Workload protection Page 331 of 677
to remain in a pending state before it fails. If the resource takes longer than
the time specified to be brought online or taken offline, the resource fails.
For more information on the Advanced Settings options, see your Windows
documentation.
4. Connection parameters—This tab controls disk replication, network routing, and
orphan files for GeoCluster.
l Disk to replicate—The volume to replicate
l Network to route Double-Take mirroring and replication traffic over—
The network to use for Storage Mirroring Recover mirroring and replication
traffic. If you do not have multiple networks established, you will only be able
to select the one network that does exist. If you do not select a network,
GeoCluster will use DNS to determine a network route to use.
Ideally, the networks used for various traffic should be separated. This is
dependent on the number of networks that you established when you created
the cluster and the priority assigned to each network. For example, if you
have two network routes, separate GeoCluster and your public traffic. If you
have three routes, separate the public traffic and then separate GeoCluster
from the cluster heartbeat.
Modifications to either of the first two settings will not take effect until the next
time the resource is brought online.
l Interval to check unresponsive nodes—The frequency to determine how
often an unresponsive node is checked to see if a Storage Mirroring Recover
connection can be made
l Delay connection until resources dependent on this one are online—
This option allows you to delay a Storage Mirroring Recover connection until
any resources that have the GeoCluster Replicated Disk resource as a
dependency are online. By ensuring that all resources that are dependent on
the GeoCluster Replicated disk resource are online before starting the
connection, the chance of a conflict occurring because application resources
are attempting to open files exclusively while GeoCluster is mirroring those
files is removed.
l Orphan files—An orphan is a file that exists in the target location but is not in
the source location. You can enable the resource to remove or delete
orphans during a mirror. If you choose to move orphan files, specify the
location where you want to move them. You should not select the system
volume for the orphan files because it could impact the stability of the cluster
service.
5. Compression—If you want to configure Storage Mirroring Recover compression,
verify that Enable Compression is selected. Depending on the compression
- HP StorageWorks 1
- Table of Contents 3
- Core operations 17
- Mirroring 18
- Replication 19
- Restoration 21
- Full-server workloads 23
- Application workloads 24
- Virtual workloads 25
- Cluster workloads 26
- Supported configurations 28
- One-to-one, active/standby 29
- One-to-one, active/active 30
- Many-to-one 31
- One-to-many 32
- Foundation Edition 38
- Standard Edition 39
- Advanced Edition 40
- Premium Edition 41
- Virtual Guest 5-Pack Edition 42
- Virtual Host Standard Edition 43
- Virtual Host Advanced Edition 44
- Virtual Host Premium Edition 45
- SQL protection requirements 53
- Virtual workload requirements 57
- ESX to ESXrequirements 64
- Cluster workload requirements 66
- Infrastructure 75
- C:\>M: 80
- Storage Mirroring Console 85
- Starting the console 86
- Getting started 87
- Inserting servers manually 88
- Managing servers 91
- Viewing server details 93
- Viewing server events 95
- Providing server credentials 96
- Console options 98
- Other consoles 101
- Replication Console 102
- Logging on and off 103
- Workspaces 115
- Failover Control Center 119
- Full-Server Failover Manager 123
- Application Manager 129
- Adding or managing servers 130
- Managing activation codes 133
- Managing ESX servers 135
- Setting up an e-mail server 136
- Workload protection 137
- Data protection 138
- Creating a replication set 142
- Simulating a connection 152
- Data workload failover 154
- Updating shares on the target 162
- Server settings 165
- Identifying a server 166
- Licensing a server 168
- Queuing data 174
- E-mailing event messages 189
- Full-server protection 192
- Finding a compatible target 193
- Routing data transmissions 204
- Mirroring data 205
- Compressing data 206
- Full-server ports 208
- Microsoft Windows ports 209
- Hardware ports 210
- Application protection 211
- Protecting an application 212
- Application advanced settings 244
- Application workload ports 253
- Exchange Failover Utility 256
- Virtual server protection 259
- Configuring ports 282
- 3. Click Save 293
- Virtual workload ports 300
- Cluster protection 303
- Protecting a standard cluster 304
- Protecting a GeoCluster 323
- Bringing the resource online 328
- Taking the resource offline 329
- Special configurations 338
- Domain controllers 339
- WINS registration 342
- WINS replication 343
- Windows DNSCMD command 345
- Non-Microsoft DNS 351
- Macintosh shares 353
- NFS Shares 355
- Workload monitoring 356
- Data workloads 357
- Monitoring a data workload 358
- Connection statistics 359
- Connection and server display 364
- Monitoring virtual workloads 375
- Viewing connection details 384
- Connection controls 391
- Monitoring a cluster workload 392
- Log files 397
- Viewing the log file 398
- Filtering the log file 404
- Monitoring event messages 414
- Event messages 415
- Statistics 445
- Viewing the statistics file 448
- Performance Monitor 457
- SNMP traps 466
- SNMP statistics 469
- Error codes 473
- Failover 479
- Full-server workload failover 484
- DNSfailover 491
- Virtual workload failover 495
- Failover Page 496 of 677 497
- Failback and restore 499
- Restoring then failing back 501
- Failing back then restoring 507
- Full-server workload diagram 512
- 1B. Reusing your source 514
- File Server 521
- Computer Browser 521
- Connections 526
- Data queues 527
- Reconnecting automatically 535
- Disconnecting a connection 538
- Mirroring automatically 542
- Mirroring Page 545 of 677 546
- Removing orphan files 547
- Replication capabilities 551
- Replication sets 555
- Replication Page 559 of 677 560
- Modifying a replication set 563
- Deleting a replication set 567
- Starting replication 568
- Verification 570
- Verifying manually 571
- Verifying on a schedule 573
- Data transmission 585
- Scheduling data transmission 587
- Snapshots 599
- Snapshots for data workloads 601
- Snapshot states 602
- Automatic snapshots 606
- Scheduling snapshots 607
- Snapshots Page 607 of 677 608
- Taking snapshots manually 609
- Recommended optimizations 612
- Planning 613
- Installation 615
- General optimizations 617
- General manageability 619
- Anti-virus protection 621
- Hardware configurations 621
- Exchange 623
- Security 626
- Security credentials 627
- Security Page 627 of 677 628
- Mirroring service 630
- Evaluations 632
- Evaluating data protection 633
- Establishing a connection 634
- Testing your target data 641
- Evaluations Page 641 of 677 642
- Monitoring failover 645
- Evaluations Page 645 of 677 646
- Simulating a failure 647
- Initiating failback 649
- Restoring your data 651
- Starting failover 659
Related products and manuals for Storage Hp Storage Mirroring Software
Storage Hp PolyServe Software User Manual
(27 pages)
(27 pages)
Storage Hp XP P9500 Storage User Manual
(182 pages)
(182 pages)
Storage Hp StorageWorks 8000 NAS User Manual
(240 pages)
(240 pages)
Storage Hp XP Array Manager Software User Manual
(105 pages)
(105 pages)
Storage Hp StoreVirtual 4000 Storage User Manual
(122 pages)
(122 pages)
© 2020, manymanuals.com. All rights reserved. | 0.454 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals