Hp Latex 3000 Printer User Manual

HPLatexDualRollKitUser Guide

3 Loading the Dual-Roll SpindleLoading the Dual-Roll Spindle —HP Latex 3000 Printer1.Insert the first roll on the rear spindle.2.Insert the second rol

2.Insert the second roll on the rear spindle.3.Center both rolls, using the marks on both sides of the center of the spindle. The input and output rol

2.Position the Dual Roll Center Support under the center of the dual roll spindle.3.Pull down the long lever.When engaging the support, make sure that

4 SpecificationsTable 4-1 Dual Roll Spindle SpecificationsLatex 3000 LX800, LX820, LX850Minimum roll width 635 mm (25 in) 914 mm (36 in)Maximumrollwi

5 Appendix Conversion TablesTable 5-1 Conversion Tables (for LX800, LX820 and LX850)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

© 2013 Hewlett-Packard DevelopmentCompany, L.P.Legal noticesThe information contained herein is subject tochange without notice.The only warran ties f

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table 5-1 Conversion Tables (for LX800, LX820 and LX850) (continued)Inches Centimeters Inches CentimetersRuler Value IPS Value Ruler Value IPS Value

Table of contents1 Introduction ...

iv ENWW

1IntroductionPurposeThis document describes the installation and use of the HP Latex Dual Roll Kit (CZ060A). For informationabout using your printer,

2 Installing the Dual Roll Center SupportAssemble the Dual Roll Center SupportNOTE:There are two Dual Roll Center Supports. The support base marked “I

Calibrate the Dual Roll Center Support1.Load a single roll spindle in the the printer.TIP:Use a single roll spindle to accurately calibrate the height

5.Manually turn the spindle 360º. Make sure there is full contact between the bearings on the support andthe face of the spindle except along the rule

8.Tighten the base nut.9.Tighten the two screws to fix the final position of the Dual Roll Center Support.NOTE:Hold the support shaft firmly in positi