HP N1200-320 User Manual Page 84
- Page / 132
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
84 Using the Command Line Interface
Select A to have the status information repeatedly refreshed.
• Select 2 from the Fibre Channel Status menu to display Attached Fibre Channel Devices.
Figure 64 Fibre Channel device display
Select R to refresh the device display (as shown in the menu above) with the latest status information
and perform manual FC discovery (as set in the Fibre Channel Configuration menu described earlier in
this chapter).
Select D to display device details.
• Select 3 to display FC Resource Status.
• Select 4 to display FC Driver Resource Status.
SyncLosses is the number of times loss of sync. was detected.
BadRxChars is the number of bad characters received.
LinkFailures is the number of link failure conditions.
BadCRCFrames is the number of frames received with a bad CRC.
ProtocolErrs is the number of protocol errors detected.
BadSCSIFrames is the number of bad SCSI frames detected.
UnderflowErrs is the number of underflow errors detected.
Fibre Channel Device Display
X.XX.XX XXXXXX XXXXXXXXXXXXXXXX
07/7/2005 08:56:22
FC Port: 0 Port id: 0x000001
R) Refresh Device Display
D) Display Device Details
X) Return to previous menu
Command, <enter> for next FC Port > r
Port 0: Requesting discovery
Doing device discovery on port 0...
Completed discovery on port 0
Fibre Channel Device Display
Version X.X XXXX
FC Port: 0 Port id: 0x000001
Port 0: TARGET DEVICE (UP) Port id: 0x000010
HP Ultrium 3-SCSI L22W Type: Direct Access
R) Refresh Device Display
D) Display Device Details
X) Return to previous menu
Table 6 Fibre Channel status
- Contents 3
- About this guide 7
- HP technical support 8
- 1Introduction 9
- Operation indicators 10
- Processing SCSI information 11
- External indicators 12
- Operating environment 12
- Non-operating environment 12
- Desktop installation 14
- Rack mount installation 14
- Connect the power cord 17
- Interfaces and connections 19
- SCSI connection 20
- Ethernet connection 20
- Serial port connection 21
- 3 Device management 23
- Discovery 24
- Logical unit management 24
- 26 Device management 26
- Configuration methods 27
- Command Line Interface 28
- Inband SCSI-3 commands 29
- Visual manager access 31
- Main menu 32
- Home page 33
- System menu 34
- Serial configuration 35
- Network configuration 36
- Active fabric configuration 37
- User security settings 38
- Real-Time Clock configuration 39
- Reset menu 40
- Ports menu 41
- SCSI bus configuration 44
- Discovery menu 45
- Mapping menu 47
- Statistics menu 49
- Utilities menu 50
- FTP utility access 51
- Trace settings configuration 52
- Event log settings 53
- Event log display 54
- Clear event log 55
- SCSI command tracking 55
- Report menu 56
- Reboot option 57
- Power-up messages 59
- Perform configuration 60
- Baud rate configuration 61
- Ethernet configuration 62
- Fibre Channel configuration 64
- Parallel SCSI configuration 67
- SCSI initiator menu 68
- Maximum SCSI bus speed menu 69
- Device mapping 70
- Adding an entry 71
- Creating an entry 72
- Remove gaps 73
- Deleting an entry 73
- Adding a host 74
- Deleting a host 75
- Editing a host 75
- Trace configuration 77
- Event configuration 78
- Real-Time clock configuration 80
- System utilities 81
- System statistics menu 82
- Channel fabric 83
- Table 6 Fibre Channel status 83
- Event Log 86
- Runtime report 86
- Diagnostics mode 87
- Get a copy of trace buffer 89
- 7Using the FTP interface 91
- 92 Using the FTP interface 92
- Updating firmware 93
- 94 Using the FTP interface 94
- 8Troubleshooting 95
- Basic verification 96
- Verify SCSI bus configuration 97
- PRLI data 98
- Running diagnostics 99
- Technical support 99
- 100 Troubleshooting 100
- APin assignments 101
- Regulatory compliance 103
- Laser device 104
- European Union notice 105
- BSMI notice 105
- Battery statement 106
- Japanese notice 106
- Korean notices 106
- C Inband SCSI-3 commands 109
- Inquiry command 110
- EVPD Page 0x80 111
- 112 Inband SCSI-3 commands 112
- Indexed addressing option 115
- SCC addressing option 115
- Network Storage Router 117
- Serial and Telnet interfaces 118
- Visual Manager 121
- Glossary 123
Related products and manuals for Networking HP N1200-320
Networking HP 2700W User Manual
(5 pages)
(5 pages)
Networking HP 706C User Manual
(123 pages)
(123 pages)
Networking HP ACC2 Aurora User Manual
(33 pages)
(33 pages)
Networking HP 720 Series User's Guide
(204 pages)
(204 pages)
(82 pages)
Networking HP X09 Manual
(56 pages)
(56 pages)
© 2020, manymanuals.com. All rights reserved. | 1.443 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals