HP N1200-320 User Manual Page 63
- Page / 132
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
N1200-320 4Gb Network Storage Router user and service guide 63
• Select 7 to toggle the DHCP setting. This setting enables/disables support for Dynamic Configuration
Protocol. The default setting is enabled. When enabled, the network storage router retrieves a
dynamic IP address from a DHCP server located on the Ethernet network that the network storage
router is connected to.
If DHCP is disabled and then enabled, it is necessary to save the current configuration and reboot the
network storage router before an IP address can be requested from the DHCP server. Use the following
four steps:
a. Select X Return to previous menu.
b. Select A Save Configuration.
c. Select X Return to previous menu.
d. Select 4 Reboot.
After the network storage router finishes rebooting, the Main menu appears on the serial interface. For
Telnet, a new session needs to be opened to continue configuring the network storage router. DHCP
status can be verified from the Ethernet Configuration menu where DHCP Configuration is indicated as
Enabled, if DHCP has been successfully activated. Note that the IP address may also appear different
than the former non-DHCP IP address.
NOTE: To use the DHCP feature, a DHCP server must be operational on the Ethernet network used by the
network storage router. If the DHCP feature is used when there is no DHCP server, the standard for DHCP
requires that the network storage router wait three minutes for a response from a DHCP server before
timing out.
Your DHCP server may allow you to set up a extended lease reservation for an IP address by providing
the server with the Ethernet MAC address of the network storage router. This sets the DHCP server to
always provide the same IP address to the network storage router. This setup can be useful for remote
management of the network storage router via Telnet or Visual Manager. Because the method of setting
up a lease reservation varies depending on the DHCP server being used, HP recommends that you
contact your Network Administrator for assistance.
• Select 8 to change security settings, including the user name and password. User names and
passwords should be unique and kept confidential and HP recommends using a combination of letters
and numbers when creating user names and passwords.
- Contents 3
- About this guide 7
- HP technical support 8
- 1Introduction 9
- Operation indicators 10
- Processing SCSI information 11
- External indicators 12
- Operating environment 12
- Non-operating environment 12
- Desktop installation 14
- Rack mount installation 14
- Connect the power cord 17
- Interfaces and connections 19
- SCSI connection 20
- Ethernet connection 20
- Serial port connection 21
- 3 Device management 23
- Discovery 24
- Logical unit management 24
- 26 Device management 26
- Configuration methods 27
- Command Line Interface 28
- Inband SCSI-3 commands 29
- Visual manager access 31
- Main menu 32
- Home page 33
- System menu 34
- Serial configuration 35
- Network configuration 36
- Active fabric configuration 37
- User security settings 38
- Real-Time Clock configuration 39
- Reset menu 40
- Ports menu 41
- SCSI bus configuration 44
- Discovery menu 45
- Mapping menu 47
- Statistics menu 49
- Utilities menu 50
- FTP utility access 51
- Trace settings configuration 52
- Event log settings 53
- Event log display 54
- Clear event log 55
- SCSI command tracking 55
- Report menu 56
- Reboot option 57
- Power-up messages 59
- Perform configuration 60
- Baud rate configuration 61
- Ethernet configuration 62
- Fibre Channel configuration 64
- Parallel SCSI configuration 67
- SCSI initiator menu 68
- Maximum SCSI bus speed menu 69
- Device mapping 70
- Adding an entry 71
- Creating an entry 72
- Remove gaps 73
- Deleting an entry 73
- Adding a host 74
- Deleting a host 75
- Editing a host 75
- Trace configuration 77
- Event configuration 78
- Real-Time clock configuration 80
- System utilities 81
- System statistics menu 82
- Channel fabric 83
- Table 6 Fibre Channel status 83
- Event Log 86
- Runtime report 86
- Diagnostics mode 87
- Get a copy of trace buffer 89
- 7Using the FTP interface 91
- 92 Using the FTP interface 92
- Updating firmware 93
- 94 Using the FTP interface 94
- 8Troubleshooting 95
- Basic verification 96
- Verify SCSI bus configuration 97
- PRLI data 98
- Running diagnostics 99
- Technical support 99
- 100 Troubleshooting 100
- APin assignments 101
- Regulatory compliance 103
- Laser device 104
- European Union notice 105
- BSMI notice 105
- Battery statement 106
- Japanese notice 106
- Korean notices 106
- C Inband SCSI-3 commands 109
- Inquiry command 110
- EVPD Page 0x80 111
- 112 Inband SCSI-3 commands 112
- Indexed addressing option 115
- SCC addressing option 115
- Network Storage Router 117
- Serial and Telnet interfaces 118
- Visual Manager 121
- Glossary 123
Related products and manuals for Networking HP N1200-320
Networking HP 2700W User Manual
(5 pages)
(5 pages)
Networking HP 706C User Manual
(123 pages)
(123 pages)
Networking HP ACC2 Aurora User Manual
(33 pages)
(33 pages)
Networking HP 720 Series User's Guide
(204 pages)
(204 pages)
(82 pages)
Networking HP X09 Manual
(56 pages)
(56 pages)
© 2020, manymanuals.com. All rights reserved. | 1.164 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals