HP E4402B User Manual Page 35
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 2 35
Front and Rear Panel Features
Rear-Panel Features
6 GPIB and parallel interface (Option A4H) is an optional interface. GPIB
supports remote analyzer operation. A parallel port is included for printing
only.
7 RS-232 and parallel interface (Option 1AX) is an optional interface. RS-232
supports remote analyzer operation. A parallel port is included for printing
only.
NOTE Printing is only supported from the parallel port.
8 IF, Video, and Sweep Ports (Option A4J or Option AYX): (Refer to the
specifications guide for more information.)
SWP OUT provides a voltage ramp corresponding to the sweep of the
analyzer (0 V to 10 V).
HI SWP IN (TTL) can be grounded to stop and reset the sweep. Once the sweep
has been stopped, removing the ground will trigger the start of a new sweep.
HI SWP OUT (TTL) is high when the analyzer is sweeping.
AUX VIDEO OUT provides detected video output (before the analog-to-digital
conversion) proportional to vertical deflection of the trace. Output is from 0
V to 1 V. Amplitude-correction factors are not applied to this signal.
AUX IF OUT is a 50 Ω, 21.4 MHz IF output that is the down-converted signal
of the RF input of the analyzer. Amplitude-correction factors are not applied
to this signal. This output is taken after the resolution bandwidth filters and
step gains and before the log amplifier.
NOTE Only one IF and Sweep Port option (Option A4J or Option AYX) can be installed at
a time.
9 FM Demod (Option BAA) demodulates, displays, and measures deviation on
FM signals. You can listen to audio signals on a built-in speaker or with an
earphone. Refer to “Det/Demod” and “FM Demodulation (Option BAA)” in the
Options chapter for more information.
Bluetooth FM Demodulation (Option 106) demodulates, displays and measures
deviation on Bluetooth signals. Refer to “Det/Demod” and “Bluetooth FM
Demodulation (Option 106)” in the Options chapter for more information.
10 Frequency Extension Assembly controls the microwave front-end
components in the Agilent E4404B, E4405B, E4407B, and E4408B.
c. Only one IF and Sweep Port option (Option A4J or Option AYX) can be
installed at a time.
d. Only one demod option (Option BAA or Option 106) can be installed at a
time.
e. The Frequency Extension Assembly comes standard with the Agilent
E4404B, E4405B and E4407B.
f. Bluetooth
is a trademark owned by its proprietor and used by Agilent
Technologies under license.
g. Option 106 is required to make measurements in Bluetooth™ Measurement
Personality (Option 228)
- Getting Started Guide 1
- Additional Information 2
- Contents 3
- 1 Installation and Setup 5
- 6 Chapter 1 6
- Initial Inspection 7
- 8 Chapter 1 8
- Chapter 1 9 9
- Power Requirements 10
- Checking the Fuse 11
- AC Power Cord 11
- 12 Chapter 1 12
- Installation and Setup 12
- Table 1-3. AC Power Cords 13
- 14 Chapter 1 14
- Using an External Reference 16
- Firmware Revision 16
- Chapter 1 17 17
- Running Internal Alignments 18
- Printer Setup and Operation 19
- 22 Chapter 1 22
- Legal Information 23
- 24 Chapter 1 24
- Front and Rear Panel Features 25
- 2.1 Front Panel Overview 26
- −12.6 V, 150 mA maximum) 28
- Auto Align is on) every time 29
- 2.1.2 Display Annotations 30
- Freq Offset 31
- 2.2 Rear-Panel Features 33
- Chapter 2 37 37
- Rear-Panel Features 37
- 2.3 Key Overview 38
- Landscape 39
- Print Setup menu 39
- 3 Making a Basic Measurement 41
- 42 Chapter 3 42
- Making a Basic Measurement 42
- Using the Front Panel 43
- Creating a User Preset 44
- Viewing a Signal 45
- Setting Frequency Span 46
- , 5, 0, MHz 46
- , Mkr ➞ Ref Lvl 47
- 48 Chapter 3 48
- ≥26 dB above the noise 49
- 50 Chapter 3 50
- 52 Chapter 4 52
- File Menu Functions 53
- 54 Chapter 4 54
- Creating a directory 55
- Formatting a Floppy Disk 56
- Saving a File 57
- 58 Chapter 4 58
- Trace (2), Min Hold. Your 58
- Step 2. Save the file 59
- Loading a file 61
- Renaming a File 63
- Copying a File 64
- Deleting a File 65
- Using the Alpha Editor 66
- 5 Options and Accessories 67
- 68 Chapter 5 68
- Options and Accessories 68
- Option Descriptions 71
- Ω to 75 Ω Matching 72
- Additional Manual Set 0B1 73
- Premium 75
- FM demodulator (Option 106) 75
- Ω, 21.4 MHz IF output 77
- Ω, 21.4 MHz IF output that 79
- Limit lines 80
- Loss compensation 80
- Ω source impedance) 82
- Accessories 83
- External Keyboard 84
- GPIB Cable 84
- Agilent E1779A Battery Pack 85
- Parallel Interface Cable 85
- Printer 85
- RF and Transient Limiters 85
- RF Bridges 85
- RS-232 Cable 86
- Static Safe Accessories 86
- 6 In Case of Difficulty 87
- 88 Chapter 6 88
- In Case of Difficulty 88
- Table 6-1 Types of Messages 89
- Check the Basics 90
- Read the Warranty 92
- Service Options 92
- Calling Agilent Technologies 92
- Chapter 6 93 93
- 94 Chapter 6 94
- Chapter 6 95 95
- 96 Chapter 6 96
- Index-97 97
- Index-98 98
- Index-99 99
- Index-100 100
Related products and manuals for Measuring, testing & control HP E4402B
Measuring, testing & control HP 132A User Manual
(330 pages)
(330 pages)
© 2020, manymanuals.com. All rights reserved. | 0.634 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals