Hp AMD Geode ECM-5510 User Manual

Part No. E2047551001R ECM-5510 5.25" AMD Geode GX466 333 MHz Mini Module with 128 MB DDR SDRAM Onboard, VGA, LVDS, Audio, LAN, CF, PC/104, PC

ECM-5510 10 ECM-5510 User’s Manual 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassi

ECM-5510 100 ECM-5510 User’s Manual 20. PRESS A KEY TO REBOOT This will be displayed at the bottom screen when an error occurs that requires you to

User’s Manual ECM-5510 User’s Manual 101 27. Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY The board ID does not match the ID stored in

ECM-5510 102 ECM-5510 User’s Manual 40. POST Codes Please take reference to Phoenix-Award website for the latest post codes. http://www.phoenix.com/

User’s Manual ECM-5510 User’s Manual 103 Code (hex) Name Description 3 Early Superio Init Early Initialized the super IO 4 Reserved 5 Blank vi

ECM-5510 104 ECM-5510 User’s Manual Code (hex) Name Description 25 Reserved 26 Reserved 27 KBC final Init Final Initial KBC and setup BIOS d

User’s Manual ECM-5510 User’s Manual 105 Code (hex) Name Description 43 Test Stuck 8259's Interrupt Bits Test 8259 Interrupt Functionality Tu

ECM-5510 106 ECM-5510 User’s Manual Code (hex) Name Description 5E Reserved 5F Reserved 60 Setup enable Display setup message and enable set

User’s Manual ECM-5510 User’s Manual 107 Code (hex) Name Description 7D Reserved 7E Reserved 7F POST error check Check POST error and display

ECM-5510 108 ECM-5510 User’s Manual 40.2 Quick POST Codes Code (hex) Name Description 65 Init onboard device Early Initialized the super IO. Res

User’s Manual ECM-5510 User’s Manual 109 Code (hex) Name Description 72 Install FDD Enter setup check and auto11 configuration check up Initial

User’s Manual ECM-5510 User’s Manual 11 1.3 Document Amendment History Revision Date By Comment 1st May, 2006 Vicky Lin Initial Release

ECM-5510 110 ECM-5510 User’s Manual 40.3 S4 POST Codes Code (hex) Name Description 5A Early Chipset Init Early Initialized the super IO. Reset V

User’s Manual ECM-5510 User’s Manual 111 40.4 BootBlock POST Codes Code (hex) Name Description 1 Base memory test Clear base memory area (0000:00

ECM-5510 12 ECM-5510 User’s Manual 1.4 Manual Objectives This manual describes in detail the Avalue Technology ECM-5510 Single Board. We have tri

User’s Manual ECM-5510 User’s Manual 13 1.5 System Specifications System CPU Onboard AMD Geode GX466 333 MHz Note: Available in different CPU s

ECM-5510 14 ECM-5510 User’s Manual Mechanical & Environmental Power Requirement +5V @ 1.71 A, 5 Vsb @ 0.17 A (with AMD Geode GX466 333 MHz

User’s Manual ECM-5510 User’s Manual 15 1.6 Architecture Overview 1.6.1 Block Diagram The following block diagram shows the architecture and main com

ECM-5510 16 ECM-5510 User’s Manual 1.6.2 AMD Geode GX2 & CS5535 The AMD Geode  GX2 processor is designed from the ground-up for information ap

User’s Manual ECM-5510 User’s Manual 17 Display controller • Supports up to 1600 x 1200 x 16 BPP and 1280 x 1024 x 24 BPP @ 85 Hz (CRT) • Hardware-

ECM-5510 18 ECM-5510 User’s Manual 1.6.3 VIA VT1612A Audio Codec VIA Technologies’ VT1612ATM 18-bit audio codec conforms to the AC’97 2.2. The VT16

User’s Manual ECM-5510 User’s Manual 19 1.6.5 Winbond W83627HF-AW LPC Super I/O The Winbond W83627F/HF is made to fully comply with Microsoft PC98 a

ECM-5510 2 ECM-5510 User’s Manual FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (

ECM-5510 20 ECM-5510 User’s Manual 1.6.7 NS DS90C385 LVDS Transmitter The DS90C385 transmitter converts 28 bits of LVCMOS/LVTTL data into four LVDS

User’s Manual ECM-5510 User’s Manual 21 2. Hardware Configuration

ECM-5510 22 ECM-5510 User’s Manual 2.1 Product Overview

User’s Manual ECM-5510 User’s Manual 23 2.2 Installation Procedure This chapter explains you the instructions of how to setup your system. 1. Turn o

ECM-5510 24 ECM-5510 User’s Manual 2.2.1 Main Memory ECM-5510 provides one 184-pin SODIMM sockets to support DDR SDRAM. The total maximum memory siz

User’s Manual ECM-5510 User’s Manual 25 • Locate the DIMM slot on the board. • Hold two edges of the DIMM module carefully. Keep away of touching i

ECM-5510 26 ECM-5510 User’s Manual 2.3 Jumper and Connector List You can configure your board to match the needs of your application by setting jump

User’s Manual ECM-5510 User’s Manual 27 Connectors Label Function Note ATX1 ATX power connector CN1 System fan connector 3 x 1 wafer, pitch 2

ECM-5510 28 ECM-5510 User’s Manual 2.4 Setting Jumpers & Connectors 2.4.1 BIOS Write Protect Select (JP1) * Default Protect* Write 2.4.2

User’s Manual ECM-5510 User’s Manual 29 2.4.3 Clear CMOS (JP3) * Default Protect* Clear CMOS 2.4.4 COM2 RS-232/422/485 Select (JP5, JP6) * Def

User’s Manual ECM-5510 User’s Manual 3 Disclaimer Avalue Technology Inc. reserves the right to make changes, without notice, to any product, includin

ECM-5510 30 ECM-5510 User’s Manual 2.4.5 COM2/4/3/1 Pin 9 Select (JP7, JP8, JP9, JP10) * Default +12V +5V Ring* 2.4.6 LCD Inverter Power Sel

User’s Manual ECM-5510 User’s Manual 31 2.4.7 Compact Flash Mode Select (JP13) * Default Master Slave* 2.4.8 DOC Memory Address Select (JP14)

ECM-5510 32 ECM-5510 User’s Manual 2.4.9 ATX Power Connector (ATX1) Signal PIN PIN Signal NC 11 1 +3.3V NC 12 2 +3.3V GND 13 3 GND PS_ON 14

User’s Manual ECM-5510 User’s Manual 33 2.4.10 System Fan Connector (CN1) Signal PIN GND 1 +12V 2 TAC 3 2.4.10.1 Signal Description – System

ECM-5510 34 ECM-5510 User’s Manual 2.4.12 TFT Panel Connector (CN3) Signal PIN PIN Signal ENBLK 39 40 NC M 37 38 LP SHFCLK 35 36 FLM GND 33

User’s Manual ECM-5510 User’s Manual 35 2.4.12.2 Signal Configuration – TFT Panel Display (CN3) Signal 18-bit TFT 24-bit TFT P0 - B0 P1 - B1 P2

ECM-5510 36 ECM-5510 User’s Manual 2.4.13 LVDS Connector (CN4) Signal PIN PIN Signal NC 39 40 NC GND 37 38 GND NC 35 36 Txclk# NC 33 34

User’s Manual ECM-5510 User’s Manual 37 2.4.14 CD-ROM Audio Input Connector (CN5) Signal PIN CD_R 4 GND 3 CD_L 2 GND 1 2.4.14.1 Signal Descri

ECM-5510 38 ECM-5510 User’s Manual 2.4.15 Serial Port 1, 3, 4 Connector (CN6) Serial Port 1 (Pin 1-10) Signal PIN PIN Signal DCD1 1 2 DSR1 R

User’s Manual ECM-5510 User’s Manual 39 2.4.15.1 Signal Description – Serial Port 1, 3, 4 Connector (CN6) Signal Signal Description TxD Serial outpu

ECM-5510 4 ECM-5510 User’s Manual Technical Support We want you to get the maximum performance from your products. So if you run into technical diff

ECM-5510 40 ECM-5510 User’s Manual 2.4.16 Serial Port 2 Connector in RS-232 Mode (CN6, Pin 11-20) Signal PIN PIN Signal DCD2 11 12 DSR2 RxD2

User’s Manual ECM-5510 User’s Manual 41 2.4.17 Serial Port 2 Connector in RS-422 Mode (CN6, Pin 11-20) Signal PIN PIN Signal TxD- 11 12 RxD+ T

ECM-5510 42 ECM-5510 User’s Manual 2.4.18 Serial Port 2 Connector in RS-485 Mode (CN6, Pin 11-20) Signal PIN PIN Signal DATA+ 11 12 NC DATA-

User’s Manual ECM-5510 User’s Manual 43 2.4.19 PC/104 Connector (CN7 + CN8) CN7 Signal PIN PIN Signal GND B32 A32 GND GND B31 A31 SA0 OSC B30

ECM-5510 44 ECM-5510 User’s Manual CN8 Signal PIN PIN Signal NC C20 D20 GND SD15 C19 D19 GND SD14 C18 D18 MASTER#SD13 C17 D17 +5V SD12 C16

User’s Manual ECM-5510 User’s Manual 45 2.4.19.1 Signal Description – PC/104 Connector (CN7 + CN8) 2.4.19.1.1 Address Signal Signal Description LA

ECM-5510 46 ECM-5510 User’s Manual 2.4.19.1.3 Commands Signal Signal Description BALE This is an active high signal used to latch valid addresses f

User’s Manual ECM-5510 User’s Manual 47 2.4.19.1.4 Transfer Response Signal Signal Description IOCS16# This is an active low signal driven by an I/

ECM-5510 48 ECM-5510 User’s Manual 2.4.19.1.6 Interrupts Signal Signal Description IRQ[3:7], IRQ[9:12] IRQ[14:15] These signals are active high sig

User’s Manual ECM-5510 User’s Manual 49 2.4.20 IrDA Connector (CN10) Signal PIN +5V 1 NC 2 IRRX 3 GND 4 IRTX 5 2.4.20.1 Signal Description –

User’s Manual ECM-5510 User’s Manual 5 Product Warranty Avalue warrants to you, the original purchaser, that each of its products will be free from d

ECM-5510 50 ECM-5510 User’s Manual 2.4.21 Keyboard & Mouse Connector (CN11) Signal PIN PIN Signal KDAT 1 2 KCLK GND 3 4 +5V MDAT 5 6 M

User’s Manual ECM-5510 User’s Manual 51 2.4.22 USB Connector 0, 1, 2 & 3 (CN12, CN15) Signal PIN PIN Signal +5V 10 9 NC D0-/D2- 8 7 GND

ECM-5510 52 ECM-5510 User’s Manual 2.4.23 LCD Inverter Connector (CN13) Signal PIN +5V 5 VR 4 ENBKL 3 GND 2 +5V / +12V 1 Note: For inverter

User’s Manual ECM-5510 User’s Manual 53 2.4.24 Primary IDE Connector (CN14) Signal PIN PIN Signal RESET# 1 2 GND PDD7 3 4 PDD8 PDD6 5 6 P

ECM-5510 54 ECM-5510 User’s Manual 2.4.24.1 Signal Description – Primary IDE Connector (CN14) Signal Signal Description PDA [2:0] IDE Address Bits

User’s Manual ECM-5510 User’s Manual 55 2.4.25 Floppy Connector (FLP1) Signal PIN PIN Signal GND 1 2 REDWC GND 3 4 NC GND 5 6 NC GND 7 8

ECM-5510 56 ECM-5510 User’s Manual 2.4.25.1 Signal Description – Floppy Connector (FLP1) Signal Signal Description RDATA The read data input signa

User’s Manual ECM-5510 User’s Manual 57 2.4.26 Digital I/O Connector (JDIO1) Signal PIN PIN Signal DIO0 1 2 DIO10 DIO1 3 4 DIO11 DIO2 5 6

ECM-5510 58 ECM-5510 User’s Manual 2.4.27 Front Panel Connector (JFP1) Signal PIN PIN Signal ALED 1 2 +5V LLED 3 4 +5V SLED 5 6 +5V GND

User’s Manual ECM-5510 User’s Manual 59 2.4.28 Audio Connector (JP4) Signal PIN PIN Signal Mic-In 1 2 Mic Bais GND 3 4 GND Line-Out L 5 6

ECM-5510 6 ECM-5510 User’s Manual Contents 1. Getting Started...

ECM-5510 60 ECM-5510 User’s Manual 2.4.29 LCD Backlight Brightness Adjustment Connector (JP12) Signal PIN GND 3 VR 2 +5V 1 VCC CN13 pin 4 JP123

User’s Manual ECM-5510 User’s Manual 61 2.4.31 Parallel Port Connector (LPT1) Signal PIN PIN Signal STB# 1 2 AFD# PD0 3 4 ERR# PD1 5 6 INI

ECM-5510 62 ECM-5510 User’s Manual 2.4.31.1 Signal Description – Parallel Port Connecter (LPT1) Signal Signal Description PD[7:0] Parallel data bu

User’s Manual ECM-5510 User’s Manual 63 2.4.33 VGA Connector (VGA1) Signal PIN PIN Signal RED 1 9 +5V GREEN 2 10 GND BLUE 3 11 NC NC 4 12

ECM-5510 64 ECM-5510 User’s Manual 3 BIOS Setup

User’s Manual ECM-5510 User’s Manual 65 3.1 Starting Setup The AwardBIOS™ is immediately activated when you first power on the computer. The BIOS rea

ECM-5510 66 ECM-5510 User’s Manual 3.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the Pag

User’s Manual ECM-5510 User’s Manual 67 • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Ent

ECM-5510 68 ECM-5510 User’s Manual 3.5 Main Menu Once you enter the AwardBIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main

User’s Manual ECM-5510 User’s Manual 69 3.5.1 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into few categories. Each cat

User’s Manual ECM-5510 User’s Manual 7 2.4.16 Serial Port 2 Connector in RS-232 Mode (CN6, Pin 11-20) ...

ECM-5510 70 ECM-5510 User’s Manual 3.5.1.2 IDE Adapter Setup The IDE adapters control the hard disk drive. Use a separate sub menu to configure eac

User’s Manual ECM-5510 User’s Manual 71 3.5.2 Advanced BIOS Features This section allows you to configure your system for basic operation. You have

ECM-5510 72 ECM-5510 User’s Manual 3.5.2.4 First/Second/Third/Other Boot Device The BIOS attempts to load the operating system from the devices in t

User’s Manual ECM-5510 User’s Manual 73 3.5.2.10 Typematic Delay <Msec> When the typematic rate is enabled, this selection allows you to select

ECM-5510 74 ECM-5510 User’s Manual 3.5.2.16 Small Logo (EPA) Show This item allows you enabled/disabled the small EPA logo show on screen at the POS

User’s Manual ECM-5510 User’s Manual 75 3.5.3 Advanced Chipset Features This section allows you to configure the system based on the specific featur

ECM-5510 76 ECM-5510 User’s Manual 3.5.3.3 Flat Panel Configuration Item Options Description Flat Panel Type TFT, LVDS Auto This item allows to

User’s Manual ECM-5510 User’s Manual 77 3.5.4 Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Item Optio

ECM-5510 78 ECM-5510 User’s Manual Item Options Description Onboard Serial Port 1 Onboard Serial Port 2 Disable 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ

User’s Manual ECM-5510 User’s Manual 79 3.5.5 Power Management Setup The Power Management Setup allows you to configure you system to most effectivel

ECM-5510 8 ECM-5510 User’s Manual 4 Drivers Installation ...

ECM-5510 80 ECM-5510 User’s Manual 3.5.5.4 IRQ Wakeup Events The VGA, LPT & COM, HDD & FDD, and PCI master are I/O events which can prevent

User’s Manual ECM-5510 User’s Manual 81 3.5.6 PnP / PCI Configuration This section describes configuring the PCI bus system. PCI, or Personal Comput

ECM-5510 82 ECM-5510 User’s Manual 3.5.6.5 PCI/VGA Palette Snoop This item is to set non-standard VGA display adapters such as graphics accelerator

User’s Manual ECM-5510 User’s Manual 83 3.5.8 Load Fail-Safe Defaults Use this menu to load the BIOS default values for the minimal/stable performan

ECM-5510 84 ECM-5510 User’s Manual 3.5.10 Set Supervisor / User Password You can set either supervisor or user password, or both of them. Superviso

User’s Manual ECM-5510 User’s Manual 85 PASSWORD DISABLED. When a password has been enabled, you will be prompted to enter it every time you try to

ECM-5510 86 ECM-5510 User’s Manual 3.5.12 Exit Without Save Abandon all CMOS value changes and exit setup, and the system is restarted after exitin

User’s Manual ECM-5510 User’s Manual 87 4 Drivers Installation Note: Installation procedures and screen shots

ECM-5510 88 ECM-5510 User’s Manual 4.1 Install Audio Driver (For AMD GX2) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the inde

User’s Manual ECM-5510 User’s Manual 89 Step6. Click Continue Anyway to run the installation. Step7. Click Finish to complete the setup.

User’s Manual ECM-5510 User’s Manual 9 30. Hard Disk(s) fail (80) → HDD reset failed...

ECM-5510 90 ECM-5510 User’s Manual 4.2 Install Display Driver (For AMD GX2) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the in

User’s Manual ECM-5510 User’s Manual 91 Step6. Click Continue Anyway to run the installation. Step7. Click Finish to complete the setup.

ECM-5510 92 ECM-5510 User’s Manual 4.3 Install Ethernet Driver (For Realtek RTL810x, RTL813x Family) Insert the Supporting CD-ROM to CD-ROM drive,

User’s Manual ECM-5510 User’s Manual 93 5 Measurement Drawing

ECM-5510 94 ECM-5510 User’s Manual (Unit: mm)

User’s Manual ECM-5510 User’s Manual 95 Appendix A: BIOS Revisions BIOS Rev. New Features Bugs/Problems

ECM-5510 96 ECM-5510 User’s Manual Appendix B: AWARD BIOS POST Messages

User’s Manual ECM-5510 User’s Manual 97 Overview During the Power On Self-Test (POST), if the BIOS detects an error requiring you to do something to

ECM-5510 98 ECM-5510 User’s Manual 5. DISPLAY SWITCH IS SET INCORRECTLY Display switch on the motherboard can be set to either monochrome or color.

User’s Manual ECM-5510 User’s Manual 99 12. Invalid EISA Configuration PLEASE RUN EISA CONFIGURATION UTILITY The non-volatile memory containing EISA