Hp ProLiant SL230s Gen8 Server User Manual Page 26
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Setup 26
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
•
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
Powering up the chassis
Connect the AC or DC power cables, depending on the power configuration.
When the circuit breakers are powered, the chassis and HP ProLiant SL Advanced Power Manager have
power. By default, each installed component also powers up. Examine the HP ProLiant SL Advanced Power
Manager for any errors which may prevent installed components from powering up.
Configuring the chassis
For further information on setting up and configuring your system, see the HP ProLiant s6500 Chassis Quick
Setup Instructions and the HP ProLiant s6500 Chassis Setup and Installation Guide.
Powering on and selecting boot options
1. Connect the Ethernet cable between the network connector on the server and a network jack.
2. Press the Power On/Standby button.
3. During the initial boot:
o To modify the server configuration ROM default settings, press F9 when prompted from the start up
sequence to enter the RBSU. By default, RBSU runs in the English language.
o If you do not need to modify the server configuration and are ready to install the system software,
press F10 to access Intelligent Provisioning.
NOTE: If an HP Smart Array controller has been added or is embedded in the system, the
controller defaults to a RAID configuration based on the size and number of drives installed. For
more information on modifying the controller default settings, see the documentation in the HP
Smart Storage Information Library (http://www.hp.com/go/smartstorage/docs).
For more information on automatic configuration, see the HP ROM-Based Setup Utility User Guide in the iLO
Management Engine Information Library (http://www.hp.com/go/ilomgmtengine/docs).
Installing the system software
To access and configure Intelligent Provisioning on a single node:
1. Access Intelligent Provisioning by rebooting the server and pressing F10.
2. The first time you log into Intelligent Provisioning, follow the steps to set preferences and activate
Intelligent Provisioning.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Rear panel components 8
- Rear panel LEDs and buttons 9
- System board components 9
- DIMM slot locations 10
- System maintenance switch 11
- Drive numbering 12
- Component identification 13 13
- Operations 15
- Remove the drive air baffle 16
- Install the drive air baffle 17
- Remove the PCI riser cage 18
- Install the PCI riser cage 19
- Optimum environment 21
- Temperature requirements 22
- Rack warnings 23
- Installing the chassis 24
- Installing options 24
- Installing the components 25
- Powering up the chassis 26
- Configuring the chassis 26
- Registering the server 27
- Introduction 28
- Processor option 28
- 11. Install the heatsink: 31
- Memory options 32
- DIMM identification 34
- Memory protection modes 34
- Installing a DIMM 37
- Drive guidelines 38
- — Left node 42
- — Right node 42
- Controller options 52
- 6. Do one of the following: 54
- 2X LFF Smart Array option 56
- 4X SFF Smart Array option 59
- Connecting the SUV cable 62
- Cabling 69
- Personality board cabling 70
- System board power cabling 71
- • Left node 72
- • Right node 72
- Mini-SAS cabling 75
- Cabling 76 76
- FBWC capacitor pack cabling 77
- Server mode 78
- HP product QuickSpecs 78
- HP iLO Management Engine 78
- Active Health System 79
- Intelligent Provisioning 80
- Erase Utility 81
- HP Service Pack for ProLiant 82
- HP ROM-Based Setup Utility 83
- Boot options 84
- Configuring AMP modes 84
- Utilities and features 85
- ROMPaq utility 86
- Keeping the system current 87
- Software and firmware 88
- Version control 88
- ProLiant servers 88
- Troubleshooting 90
- Regulatory information 92
- Electrostatic discharge 93
- Specifications 94
- Support and other resources 95
- Customer Self Repair 97
- Reparo feito pelo cliente 99
- Acronyms and abbreviations 103
- Documentation feedback 107
- Index 108 108
- Index 109 109
- Index 110 110
Related products and manuals for Computer hardware Hp ProLiant SL230s Gen8 Server
(91 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 1.470 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals