Hp MPX200 Multifunction Router User Manual Page 102
- Page / 180
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
rescan devices
Rescan the devices for new LUNs.
Authority
admin
Syntax
rescan devices
Examples
The following shows an example of the rescan devices command.
nl
MPX200 <1> (admin) #> rescan devices
nl
Index State (Symbolic Name, WWPN/WWNN,WWPN/iSCSI Name, Ip Address)
----- ----- ------------------------------------------------------
0 Online HP HSV200-0, 50:00:1f:e1:50:0a:e1:49
1 Online DGC RAID-2, 50:06:01:62:41:e0:49:2e
2 Online HP HSV210-2, 50:00:1f:e1:50:0a:37:18
3 Online NETAPP LUN-3, 50:0a:09:82:98:8c:a7:79
nl
Please select a Array/Target from the list above ('q' to quit): 0
nl
Successfully initiated rediscovery on selected targets.
reset
Restores the router configuration parameters to the factory default values.
The reset factory command deletes all LUN mappings, as well as all persistent data regarding
targets, LUNs, initiators, virtual port group settings, log files, iSCSI and MGMT (management port)
IP addresses, FC and Ethernet port statistics, and passwords. This command also restores the factory
default IP addresses. Issue the reset factory command on either an individual blade or on the
chassis. On the chassis, this command resets both the blades to their factory defaults.
The reset mappings command clears all information except the MGMT and iSCSI IP address.
Authority
admin
Syntax
reset
Keywords
Deletes router configuration and reverts the settings to the factory defaults.factory
Deletes router mappings and resets them to factory defaults.mappings
Examples
The following example shows the reset factory command:
MPX200 <1> (admin) #> reset factory
Are you sure you want to restore to factory default settings (y/n): y
Please reboot the System for the settings to take affect.
The following example shows the reset factory command on the chassis:
MPX200 <1> (admin) #> reset factory
This command will reset BOTH blades to there factory defaultsettings. Both blades will be rebooted automatically.
Are you sure you want to reset the chassis to factory defaults? (y/n): y
The following example shows the reset mappings command:
102 Command line interface
- Migration User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 1 Introduction 8
- 2 Getting started 10
- Data migration configuration 11
- 12 Getting started 12
- Supported configurations 13 13
- 14 Getting started 14
- Supported configurations 15 15
- Supported FC fabrics 16
- Supported storage arrays 16
- Hardware and software setup 17
- Software setup 18
- 3 Data migration objects 19
- Data migration job groups 20
- Data migration jobs 20
- Migration types 21
- Job scheduling 21
- Job states 22
- Job failover and failback 23
- VPG examples 24
- Presented targets 25
- 26 Data migration objects 26
- Global presentation 27
- Recommended steps 29
- Remote peers 30
- Online remote migration 30
- Online remote migration 31 31
- Data scrubbing 33
- Protection 34
- Users 35 35
- 4 Data migration licenses 36
- 38 Data migration licenses 38
- 40 Data migration licenses 40
- 5 Performing data migration 41
- Configuring the fabric 42
- Presenting LUNs to the MPX200 43
- 44 Performing data migration 44
- Rescanning Targets 45
- 46 Performing data migration 46
- 48 Performing data migration 48
- Mapping LUNs to initiators 49
- Mapping LUNs to hosts 50
- Using remote peers 51
- Importing a remote array 52
- Setting array properties 53
- 54 Performing data migration 54
- 56 Performing data migration 56
- 58 Performing data migration 58
- 60 Performing data migration 60
- 62 Performing data migration 62
- System Log 63
- Data migration job log 64
- 66 Performing data migration 66
- 68 Performing data migration 68
- Removing an offline array 69
- Creating and removing a DML 69
- 70 Performing data migration 70
- 72 Performing data migration 72
- 74 Performing data migration 74
- 6 Command line interface 76
- Command syntax 77
- Commands 77
- Commands 85 85
- 94 Command line interface 94
- Commands 95 95
- 96 Command line interface 96
- Commands 97 97
- 100 Command line interface 100
- Authority 101
- Keywords 101
- Examples 101
- 102 Command line interface 102
- 104 Command line interface 104
- 108 Command line interface 108
- Commands 109 109
- 112 Command line interface 112
- Commands 113 113
- Commands 117 117
- 118 Command line interface 118
- Commands 121 121
- 122 Command line interface 122
- 130 Command line interface 130
- 136 Command line interface 136
- Performance factors 139
- Maximizing performance 139
- Operational Behavior 140
- Best practices 141
- General precautions 142
- MSA2012fc Array Behavior 144
- 14. Reboot the MPX200 145
- 9 Restrictions 146
- Contacting HP 148
- Related information 148
- Prerequisites 149
- Typographic conventions 149
- Product feedback 150
- 11 Documentation feedback 151
- Linux multipath configuration 153
- HP-UX multipath configuration 156
- Pre-insertion requirements 162
- SNMP Parameters 164
- SNMP trap configuration 164
- Notifications 165
- 166 SNMP 166
- Notifications 167 167
- D HP-UX Boot volume migration 168
- PA-RISC systems 170
- Itanium Systems 170
- E Troubleshooting 171
- Glossary 174
- 176 Glossary 176
- 178 Index 178
- 180 Index 180
Related products and manuals for Storage Hp MPX200 Multifunction Router
Storage Hp XP Array Manager Software User Manual
(172 pages)
(172 pages)
Storage Hp XP Business Copy Software User Manual
(117 pages)
(117 pages)
Storage Hp XP20000XP24000 Disk Array User Manual
(226 pages)
(226 pages)
© 2020, manymanuals.com. All rights reserved. | 0.306 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals