Hp MPX200 Multifunction Router User Manual Page 104
- Page / 147
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
A Simple Network Management Protocol
SNMP provides monitoring and trap functions for managing the router through third-party
applications that support SNMP. The router firmware supports SNMP versions 1 and 2, and an
MIB (see “Management Information Base” (page 104)). You may format traps using SNMP version
1 or 2.
SNMP parameters
You can set the SNMP properties using SANsurfer Router Manager or the CLI. Table 7 (page 104)
describes the SNMP parameters.
Table 7 SNMP parameters
DescriptionParameter
A password that authorizes an SNMP management server to read information from the
router. This is a write-only field. The value on the router and the SNMP management server
Read community
must be the same. The read community password can be up to 32 characters, excluding
the number sign (#), semicolon (;), and comma (,). The default password is private.
A password that authorizes an SNMP management server to receive traps. This is a
write-only field. The value on the router and the SNMP management server must be the
Trap community
same. The trap community password can be up to 32 characters, excluding the number
sign (#), semicolon (;), and comma (,). The default password is private.
Specifies the name of the router location. The name can be up to 64 characters, excluding
the number sign (#), semicolon (;), and comma (,). The default is undefined.
System location
Specifies the name of the person to be contacted to respond to trap events. The name can
be up to 64 characters, excluding the number sign (#), semicolon (;), and comma (,). The
default is undefined.
System contact
Enables or disables the generation of authentication traps in response to authentication
failures. The default is disabled.
Authentication traps
SNMP trap configuration
SNMP trap configuration lets you set up to eight trap destinations. Choose from Trap 1 through
Trap 8 to configure each trap. Table 8 (page 104) describes the parameters for configuring an
SNMP trap.
Table 8 SNMP trap configuration parameters
DescriptionParameter
Enables or disables trap n. If disabled, the trap is not configured.Trap n enabled
Specifies the IP address to which the SNMP traps are sent. A maximum of eight trap
addresses are supported. The default address for traps is 0.0.0.0.
Trap address
1
Port number on which the trap is sent. The default is 162. If the trap destination is not
enabled, this value is 0 (zero). Most SNMP managers and management software listen
on this port for SNMP traps.
Trap port
1
Specifies the SNMP version (1 or 2) with which to format traps.Trap version
1
Trap address (other than 0.0.0.0.) and trap port combinations must be unique. For example, if trap 1 and trap 2 have
the same address, they must have different port values. Similarly, if trap 1 and trap 2 have the same port value, they
must have different addresses.
Management Information Base
This section describes the tables included in the MIB.
104 Simple Network Management Protocol
- Line Interface User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 CLI overview 6
- 2 Command reference 11
- 12 Command reference 12
- 14 Command reference 14
- Authority 15
- Keywords 15
- Examples 15
- 16 Command reference 16
- 1: admin start 20
- 3: history 20
- 22 Command reference 22
- 24 Command reference 24
- LUN iSCSI global map 28
- LUN mask 30
- LUN remap 32
- 36 Command reference 36
- 38 Command reference 38
- Admin session 44
- 46 Command reference 46
- 52 Command reference 52
- 56 Command reference 56
- 58 Command reference 58
- 66 Command reference 66
- 72 Command reference 72
- 80 Command reference 80
- WAN link test 82
- Stopping the test 85
- 3 Configuring CHAP 86
- 88 Configuring CHAP 88
- 4 Virtual port groups 89
- 90 Virtual port groups 90
- 92 Virtual port groups 92
- Prerequisites 93
- Discovering the iSCSI targets 93
- Server, MPX200, storage 97
- Fibre Channel switch and IP 97
- 6 Support and other resources 101
- 7 Documentation feedback 103
- SNMP parameters 104
- SNMP trap configuration 104
- Management Information Base 104
- Network port table 105
- Fibre Channel port table 106
- Initiator object table 108
- LUN table 109
- Virtual port group table 111
- Sensor table 112
- Notifications 113
- Notification objects 114
- Agent startup notification 115
- Agent shutdown notification 115
- Target device discovery 115
- Target presentation (mapping) 116
- Sensor notification 116
- Notifications 117 117
- B Log messages 119
- Glossary 139
- 140 Glossary 140
- 142 Glossary 142
- 144 Index 144
- 146 Index 146
Related products and manuals for Storage Hp MPX200 Multifunction Router
Storage Hp D2200sb Storage Blade User Manual
(49 pages)
(49 pages)
Storage Hp X500 Data Vault User Manual
(331 pages)
(331 pages)
© 2020, manymanuals.com. All rights reserved. | 2.423 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals