Hp Brocade 8Gb SAN Switch for HP BladeSystem c-Class User Manual Page 15
- Page / 59
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
9. Identify the interconnect bay number where the switch is installed. At the OA command line,
enter:
connect interconnect x, where x is the interconnect bay slot where the switch is installed:
• User: admin
• Password: password
Enter entries as shown; commands are case sensitive.
10. Or follow the onscreen prompts to change your password now.
11. The OA will connect its serial line to the Switch in the specified interconnect bay. A prompt
displays, indicating that the escape character for returning to the OA is Ctrl __ (underscore).
12. At the command line, enter: ipaddrset.
13. Enter the remaining IP addressing information as prompted.
14. Optionally, enter ipaddrshow at the command prompt to verify that the IP address is set
correctly.
15. Record the IP addressing information, and store it in a safe place.
16. Enter Exit, and then press Enter to log out of the serial console.
17. Disconnect the serial cable. For additional assistance with operating the Onboard Administrator
CLI, see the Onboard Administrator Command Line Interface User Guide for your specific
enclosure, available at http://www.hp.com.
Configure the 8Gb SAN Switch
The 8Gb SAN Switch must be configured to ensure correct operation within a network and fabric.
For instructions about configuring the switch to operate in a fabric containing switches from other
vendors, see the HP SAN Design Reference Guide:
http://h18000.www1.hp.com/products/storageworks/san/documentation.html
For more information about the CLI, see the latest version of the Fabric OS command reference.
Items required for configuration
The following items are required for configuring and connecting the 8Gb SAN Switch for use in
a network and fabric:
• 8Gb SAN Switch installed in the enclosure
• IP address and corresponding subnet mask and gateway address recorded during the “Setting
the IP address manually” (page 14) procedure
• Ethernet cable
• SFP transceivers and compatible optical cables, as required
• Access to an FTP server for backing up the switch configuration (optional)
Connect to the Command Line Interface
Make an Ethernet connection and log in to the 8Gb SAN Switch:
1. Connect the workstation to the Ethernet network containing the OA. If the OA is not on a
network, connect directly to the OA/iLO Ethernet port on the active OA.
IMPORTANT: Verify that the switch is not being reconfigured from any other connections
during the remaining steps.
2. Open a Telnet connection using the IP address set earlier. The login prompt displays when
the Telnet connection locates the switch in the network.
3. Enter the user name, using the administrative account admin.
4. Enter the password. The default password is password.
Configure the 8Gb SAN Switch 15
- Brocade 8Gb SAN Switch for HP 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 Overview 6
- Internal ports summary 7
- ISL trunking groups 8
- Supported optional software 8
- 1. Fabric OS 7.2.0a or later 9
- Shipping carton contents 10
- Install the 8Gb SAN Switch 11
- 12 Setup 12
- OA power verification 13
- Check LEDs 13
- Using external DHCP 14
- Configure the 8Gb SAN Switch 15
- Verifying installed licenses 16
- Setting the date and time 16
- Disabling and enabling a port 17
- DPOD commands 18
- Verifying the configuration 19
- Backing up the configuration 19
- 3 Managing the 8Gb SAN Switch 20
- Diagnostic tests 21
- Powering on and off 22
- Interpreting LED activity 22
- LED patterns 22
- POST and boot specifications 23
- Firmware update 24
- About the Reset button 25
- 4 Support and other resources 27
- Typographic conventions 28
- Customer self repair 29
- General specifications 30
- Environmental requirements 31
- Supported SFPs 31
- Supported HBAs 31
- FCC rating label 32
- European Union notice 33
- Japanese notices 34
- Korean notices 35
- Taiwanese notices 35
- Turkish recycling notice 35
- Vietnamese notice 36
- Laser compliance notices 36
- French laser notice 37
- German laser notice 37
- Italian laser notice 37
- Recycling notices 38
- Czech recycling notice 39
- Danish recycling notice 39
- Dutch recycling notice 39
- Estonian recycling notice 40
- Finnish recycling notice 40
- French recycling notice 40
- German recycling notice 40
- Greek recycling notice 41
- Hungarian recycling notice 41
- Italian recycling notice 41
- Latvian recycling notice 41
- Lithuanian recycling notice 42
- Polish recycling notice 42
- Portuguese recycling notice 42
- Romanian recycling notice 42
- Battery replacement notices 43
- French battery notice 44
- German battery notice 44
- Italian battery notice 45
- Japanese battery notice 45
- Safety guidelines 46
- Battery replacement notice 47
- Power cords 47
- Japanese power cord notice 48
- China RoHS 49
- China RoHS 51 51
- Glossary 52
- 54 Glossary 54
- 56 Glossary 56
- 58 Index 58
Related products and manuals for Storage Hp Brocade 8Gb SAN Switch for HP BladeSystem c-Class
Storage Hp XP Array Manager Software User Manual
(172 pages)
(172 pages)
Storage Hp XP Business Copy Software User Manual
(117 pages)
(117 pages)
© 2020, manymanuals.com. All rights reserved. | 0.776 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals