HP 9000 rp7410 Installation Guide download pdf (Page 17)

Chapter 1

Introduction

Overview

MP/SCSI Core I/O Board

The HP 9000 rp7420 Server accommodates two sets of core I/O functionality. Each core I/O board set consists

of a MP/SCSI Core I/O board and a Procurium LAN/SCSI board. At least one MP/SCSI Core I/O board

inserted in slot 1 is required (independent of partitions). An additional MP/SCSI Core I/O board can be added

in slot 0 as well (and is required in a dual partition system). Both MP/SCSI Core I/O boards are oriented

vertically and plug into the system backplane from the rear of the server. See Figure 1-3 on page 6. The

MP/SCSI Core I/O board incorporates a dual channel Ultra160 SCSI controller.

Procurium LAN/SCSI Board

At least one Procurium LAN/SCSI board is required for the minimum system configuration; two are required

in a dual partition system. The Procurium board is a standard PCI form factor card with PCI card edge

connectors. The PCI-X backplane has slot 8 in partition 1 reserved for the required, primary Procurium board

and slot 1 in partition 0 supports either a 2nd Procurium board or any other supported add-in PCI-X card.

The Procurium board is hot-pluggable.

Table 1-1 PCI-X Slot Types

I/O

Partition

Slot

Device

a. If the slot is used as a PCI slot then either the 33 MHz or 66 MHz PCI frequency is supported. If

the slot is used as a PCI-X slot then either the 66 MHz or 133 MHz PCI-X frequency is supported.

0 8 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

0 7 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

0 6 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

0 5 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

0 4 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

0 3 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

0 2 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

b. Slot 1 in Partition 0 supports secondary LAN/SCSI card of core I/O set.

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

c. Slot 8 in Partition 1 supports primary LAN/SCSI card of core I/O set.

PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 7 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 6 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 5 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 4 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 3 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 2 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 1 PCI (33 or 66 MHz) / PCI-X (66 or 133 MHz) 64-bit, 3.3V connector, Hot Plug Slot

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 75 76

No comments

HP 9000 rp7410 Installation Guide Page 17