HP X09 Manual download pdf (Page 16)

XStream‐PKG‐E™EthernetRFModem–ProductManualv5.x00[2006.02.24]

Pin Sleep (SM = 1)

Pin Sleep requires the least amount of power. In order to achieve this state, DI3 (SLEEP) pin

must be asserted (high). The modem remains in Pin Sleep until the DI3 pin is de-asserted.

After enabling Pin Sleep, the SLEEP pin controls whether the XStream Modem is active or in Sleep

Mode. When DI3 is de-asserted (low), the modem is fully operational. When DI3 is asserted

(high), the modem transitions to Sleep Mode and remains in its lowest power-consuming state

until the DI3 (SLEEP) pin is de-asserted. DI3 is only active if the modem is setup to operate in

this mode; otherwise the pin is ignored.

Once in Pin Sleep Mode, DO2 (

) is de-asserted (high), indicating that data should not be sent

to the modem. The PWR pin is also de-asserted (low) when the modem is in Pin Sleep Mode.

Note: The module will complete a transmission or reception before activating Pin Sleep.

Serial Port Sleep (SM = 2)

Serial Port Sleep is a Sleep Mode in which the XStream Modem runs in a low power state until

serial data is detected on the DI pin.

When Serial Port Sleep is enabled, the modem goes into Sleep Mode after a user-defined period

of inactivity (no transmitting or receiving of data). This period of time is determined by ST (Time

before Sleep) Command. Once a character is received through the DI pin, the modem returns to

Idle Mode and is fully operational.

Cyclic Sleep (SM = 3-8)

Cyclic Sleep is the Sleep Mode in which the XStream Modem enters into a low-power state and

awakens periodically to determine if any transmissions are being sent.

When Cyclic Sleep settings are enabled, the XStream Modem goes into Sleep Mode after a user-

defined period of inactivity (no transmission or reception on the RF channel). The user-defined

period is determined by ST (Time before Sleep) Command.

While the modem is in Cyclic Sleep Mode, DO2 (

) is de-asserted (high) to indicate that data

should not be sent to the modem during this time. When the modem awakens to listen for data,

DO2 is asserted and any data received on the DI Pin is transmitted. The PWR pin is also de-

asserted (low) when the modem is in Cyclic Sleep Mode.

The modem remains in Sleep Mode for a user-defined period of time ranging from 0.5 seconds to

16 seconds (SM Parameters 3 through 8). After this interval of time, the modem returns to Idle

Mode and listens for a valid data packet for 100 ms. If the modem does not detect valid data (on

any frequency), the modem returns to Sleep Mode. If valid data is detected, the modem

transitions into Receive Mode and receives incoming RF packets. The modem then returns to

Sleep Mode after a Period of inactivity that is determined by ST “Time before Sleep” Command.

The modem can also be configured to wake from cyclic sleep when SLEEP/DI3 is de-asserted

(low). To configure a modem to operate in this manner, PW (Pin Wake-up) Command must be

issued. Once DI3 is de-asserted, the modem is forced into Idle Mode and can begin transmitting

or receiving data. It remains active until no data is detected for the period of time specified by

the ST Command, at which point it resumes its low-power cyclic state.

Note: The cyclic interval time defined by SM (Sleep Mode) Command must be shorter than the interval

time defined by LH (Wake-up Initializer Timer). [Refer to figures below.]

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 55 56

Comments to this Manuals

No comments

HP X09 Manual Page 16

Comments to this Manuals

Related products and manuals for Networking HP X09