Hp ProLiant BL280c G6 Server-Blade User Manual Page 20
- Page / 108
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Hardware options installation 20
Hardware options installation
Introduction
If more than one option is being installed, read the installation instructions for all the hardware options and
identify similar steps to streamline the installation process.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: To prevent damage to electrical components, properly ground the server before
beginning any installation procedure. Improper grounding can cause electrostatic discharge.
Hard drive option
The HP ProLiant BL280c G6 Server Blade supports midline SATA hard drives and 9.5-mm SATA hard drives.
SAS hard drives are supported when the HP Smart Array P712m Controller option is installed. The HP Smart
Array P712m Controller option does not support hard drive activity LEDs when installed in the HP ProLiant
BL280c G6 Server Blade.
For information on supported hard drive options and controller options, see the server blade QuickSpecs on
the HP website (http://www.hp.com).
CAUTION: Failure to follow the hard drive installation guidelines can cause hardware damage.
Always observe the installation guidelines:
• Always install a spacer when installing a 9.5-mm SATA hard drive.
• Be sure to use the proper screws when installing the hard drive:
o When installing a 9.5-mm SATA hard drive and a hard drive spacer, install the long hard drive
screws that are stored on the hard drive spacer.
o When installing a midline SATA hard drive or a SAS hard drive, install the standard hard drive
screws that ship with the server blade.
To install the component:
1. Power down the server blade (on page 11).
2. Remove the server blade (on page 12).
3. Remove the access panel (on page 13).
4. Remove the air baffle.
5. Install the hard drives.
CAUTION: When installing midline SATA hard drives in the server blade, always install the
standard hard drive screws provided with the server blade. Installing the long hard drive screws
located on the hard drive spacer can damage the hard drive.
- User Guide 1
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- System board components 8
- DIMM slot locations 9
- System maintenance switch 9
- HP c-Class Blade SUV Cable 10
- Operations 11
- Remove the server blade 12
- Remove the access panel 13
- Install the access panel 13
- Remove the air baffle 13
- Install the air baffle 13
- Overview 15
- Connecting to the network 17
- Installing a server blade 18
- Completing the configuration 19
- Introduction 20
- Hard drive option 20
- Processor option 22
- Memory options 27
- DIMM identification 28
- Memory configurations 29
- Installing a DIMM 35
- Mezzanine card option 36
- Cabling 47
- USB devices 48
- USB diskette 50
- Item Description 50
- Network-based PXE deployment 52
- Deployment methods 54
- CD-ROM deployment 55
- Diskette image deployment 56
- Configuration tools 57
- HP ROM-Based Setup Utility 58
- Auto-configuration process 59
- Boot options 59
- BIOS Serial Console 59
- Array Configuration Utility 60
- Management tools 62
- Erase Utility 63
- Redundant ROM support 63
- Diagnostic tools 64
- Integrated Management Log 65
- Keeping the system current 66
- Care Pack 67
- Troubleshooting 68
- Symbols on equipment 69
- Warnings 69
- Symptom information 70
- Troubleshooting 71 71
- Loose connections 72
- Service notifications 72
- Server health LEDs 72
- Troubleshooting flowcharts 72
- Start diagnosis flowchart 73
- General diagnosis flowchart 74
- Symptoms: 76
- POST problems flowchart 78
- OS boot problems flowchart 80
- • Corrupted OS 81
- • Redundancy failure 83
- (http://www.hp.com/support) 84
- Troubleshooting 85 85
- Battery replacement 86
- FCC rating label 87
- Class A equipment 87
- Class B equipment 87
- Modifications 88
- • EMC Directive 2004/108/EC 89
- Japanese notice 90
- BSMI notice 90
- Korean notice 90
- Chinese notice 91
- Laser compliance 91
- Battery replacement notice 91
- Electrostatic discharge 93
- Specifications 94
- Technical support 95
- Technical support 96 96
- Customer Self Repair 97
- Technical support 98 98
- Reparo feito pelo cliente 99
- Technical support 100 100
- Technical support 101 101
- Technical support 102 102
- Acronyms and abbreviations 103
- Index 105 105
- Index 106 106
- Index 107 107
- Index 108 108
Related products and manuals for Computer hardware Hp ProLiant BL280c G6 Server-Blade
(125 pages)© 2020, manymanuals.com. All rights reserved. | 0.350 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals