Hp Integrity Superdome 2 Server User Manual Page 165
- Page / 197
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
11 Using the serial connection
Setting up Onboard Administrator using the CLI
1. Connect to the Onboard Administrator CLI using the serial port, management port, or service
port.
2. Log into the Onboard Administrator with the Administrator user account and the OA dogtag
password.
3. Set Onboard Administrator name by running the SET OA NAME 1 <name> command.
4. If a redundant Onboard Administrator is present, run the SET OA NAME 2 <name> command.
5. Configure Onboard Administrator IP address:
a. Select either the OA1/OA2 IP address or Enclosure IP address.
b. Configure OA1 IP address as static or DHCP. Example for static, run the SET IPCONFIG
STATIC 1 <ipaddress> <netmask> command
6. If a redundant Onboard Administrator is present, run the SET IPCONFIG STATIC 2 <ip
address> <netmask> command
7. Set Onboard Administrator gateway by running the SET OA GATEWAY 1 <ip address>
command
8. If a redundant Onboard Administrator is present, run the SET OA GATEWAY 2 <ip
address> command
9. Set the iLO IP address by running the SET EBIPA BLADE <ip address> <netmask>
command. Allocate each IP address (up to 32) consecutive static IP addresses.
10. If a gateway exists on the management network, set the iLO gateway to the IP address, run
the SET EBIPA BLADE GATEWAY <ip address> command
11. Start EBIPA for iLO by running the ENABLE EBIPA BLADE command
12. Complete the remainder of the settings as required. For information on the enclosure defaults
for each setting, see the HP Integrity Superdome 2 Onboard Administrator Command Line
Interface User Guide.
Configuring Superdome 2 server blade iLO 3 IP addresses
Each Superdome 2 server blade iLO 3 factory default configuration enables DHCP network settings.
To use the server blade with a DHCP network, connect the Onboard Administrator management
port to a network with a DHCP server and Onboard Administrator and all iLO 3 management
processors and supporting interconnect modules get IP addresses from the DHCP server.
To configure each server blade for static IP addresses, use Onboard Administrator to setup an IP
address for each iLO using EBIPA. This enables iLO to be addressed using TCP/IP so that the
network settings can be reconfigured.
Configuring each server blade with an IP address using EBIPA provides a fixed network configuration
including IP address, netmask and gateway - that is based on the enclosure bay where the server
is installed. The new iLO 3 gets the IP address for that bay without additional configuration needed.
Pinout signals for Onboard Administrator Serial RS232 connector
The pinout for the DB9 serial connector (Onboard Administrator Serial RS232 port) used on the
Superdome 2 serial port is.
DescriptionDirectionNamePin
Carrier detectInCD1
Receive dataInRXD2
Setting up Onboard Administrator using the CLI 165
- Administrator User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 1 Introduction 8
- Access requirements 10
- 514Remote syslog 11
- Interfaces 12
- Role-based user accounts 13
- 14 Introduction 14
- Running the setup wizard 15
- Using online help 16
- Insight Display overview 18
- ◦ Power Supply Redundant 20
- Health Summary screen 24
- Enclosure Settings screen 25
- Enclosure Info screen 26
- Blade and Port Info screen 27
- View User Note screen 29
- Chat Mode screen 29
- Insight Display errors 30
- Location errors 31
- Configuration errors 31
- Device failure errors 31
- Setting up the Door Display 32
- Complex configuration 33
- Status display preferences 34
- Two 16s complex setup 34
- Complex login 36
- Door Display status menu 36
- UID control 37
- Display Settings menu 38
- Firmware Update menu 39
- 4 First Time Setup Wizard 41
- 42 First Time Setup Wizard 42
- Local User Accounts screen 45
- User Settings screen 46
- Directory Groups screen 48
- SNMP Settings screen 50
- Navigation overview 55
- Individual device pages 56
- Graphical view navigation 57
- Selecting a device 58
- Status reporting 58
- Device security 58
- Minimizing the graphical view 59
- 6 Complex Overview 60
- Compute Enclosures tab 61
- Power and Thermal tab 61
- Complex Information screen 63
- Information tab 65
- Settings box 66
- Complex Logs tab 67
- Complex CLI Tab 67
- Introduction 68
- Services unavailable 69
- Management Processor access 69
- Event logs 70
- IPMI Watchdog 70
- Partition ID 70
- Affected OS Commands 72
- Network Services to OA 72
- Frequently asked questions: 72
- Known issues: 73
- Firmware Update screen 74
- Firmware image download 75
- Firmware analysis 75
- Update Status 76
- Enclosure DVD Module screen 77
- Viewing the status screens 79
- Enclosure settings 80
- Diagnostic information 81
- Enclosure Information tab 82
- AlertMail screen 83
- Date: Date in standard format 84
- To: RECEIVER MAILBOX 84
- Sample email 85
- Device Bays Standard tab 86
- Interconnect Bays tab 86
- Date and Time screen 87
- NTP settings 88
- Network Access screen 89
- Trusted Hosts tab 90
- Link Loss Failover screen 91
- Configuration Scripts screen 96
- Device Summary screen 97
- Onboard Administrator Module 98
- Table 8 Status information 99
- Hardware information 99
- TCP/IP Settings screen 101
- Requied Information 104
- Optional Information 105
- System log 106
- Device bays 111
- Virtual Power 112
- One Time Boot 112
- UID State 112
- Device bays 113 113
- Port Mapping Information 114
- Status information 114
- Diagnostic Information 114
- CPU Status 115
- Temperature Sensors 116
- Device Bay Information tab 116
- Device Information 117
- Server NIC Information 117
- Mezzanine Card Information 117
- CPU and memory information 117
- Table 9 CPU Information 117
- Interconnect bays 118
- Interconnect Bay Status tab 120
- Hardware Information 121
- Connectivity information 122
- XFM bays 123
- XFM Bay Status tab 125
- XFM Bay Information tab 126
- XFM Bay Virtual Buttons 126
- GPSM bays 127
- GPSM Bay Information screen 128
- Enclosure power management 129
- Power and Thermal screen 130
- Power Management screen 131
- Power Subsystem screen 133
- Power Subsystem information 134
- Power supply status 134
- Fans and cooling management 136
- Fan Information - Bay screen 139
- Managing users 140
- Local Users screen 142
- Edit Local User 143
- Privilege level change 144
- Password Settings screen 145
- Directory Settings screen 146
- Directory Test Settings tab 147
- Directory Groups 149
- Add an LDAP Group screen 150
- Edit an LDAP Group screen 151
- SSH Administration screen 152
- HP SIM Integration screen 153
- Certificate Owner Field 154
- Signed In users 155
- Insight Display 156
- IOX Status tab 157
- IOX Information tab 158
- IOX Power and Thermal screen 159
- IOX Power Subsystem screen 160
- IOX Thermal Subsystem screen 161
- Thermal Subsystem information 162
- Fan information 162
- 9 Port mapping 163
- 10 Using the CLI 164
- DescriptionDirectionNamePin 165
- Carrier detectInCD1 165
- Receive dataInRXD2 165
- Configuration scripts 167
- Reset Factory Defaults screen 168
- 13 Troubleshooting 169
- 170 Troubleshooting 170
- 172 Troubleshooting 172
- 174 Troubleshooting 174
- 176 Troubleshooting 176
- Soap interface errors 178
- File Upload errors 178
- Administrator 179
- Microsoft Active Directory 181
- Creating directory groups 184
- Before you contact HP 187
- HP contact information 187
- Subscription service 187
- Documentation feedback 187
- Related information 188
- Typographic conventions 188
- Typographic conventions 189 189
- A Time zone settings 190
- Asia time zone settings 192
- Universal time zone settings 192
- Oceanic time zone settings 193
- Europe time zone settings 193
- Polar time zone settings 194
- 196 Index 196
Related products and manuals for Computer hardware Hp Integrity Superdome 2 Server
(46 pages)
(93 pages)© 2020, manymanuals.com. All rights reserved. | 1.415 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals