MODEL HPT 100 SERIESHIGH PURITY PRESSURETRANSMITTERINSTRUCTIONS FOR INSTALLATION,OPERATION AND CALIBRATIONU.S GAUGE DIVISONPMT PRODUCTS
SECTION I SAFETY APPROVALSAmetek UHP Transmitter Safety Approvals:The model HPT 100 transm
To eliminate the need for a protective enclosure, one may achieve Div 2 compliance byusing a suitable barrier(s) as described in Drawing K750525/K7505
pg. 1-8
DECLARATION OF CONFORMITY(In accordance with EN45014)We,AMETEK US GAUGE DIVISIONPMT PRODUCTS820 Pennsylvania Blvd.Feasterville, PA. USA 19053declare t
SECTION II INSTALLATIONThe HPT 100 Series transmitters are packaged in a Class 100 cleanroom environment.The units are carefully double-bagged with a
SECTION II ELECTRICALInstallation Notes on Ametek UHP 4-20 mA TransmitterWiring Notes: Bendix® compatible connector1. Hookup: The 4-20 mA transmitt
Installation Notes on Ametek UHP 4-20 mA Transmitter (continued)Wiring Notes: 4-20 mA. pigtail cable style1. Hookup: The 4-20 mA transmitter utilize
SECTION II ELECTRICALInstallation Notes on Ametek UHP 0-5 Vdc TransmitterWiring Notes: Bendix® compatible connector (0-5 Vdc)1. Hookup: The 0-5 Vdc
Installation Notes on Ametek UHP 0-5 Vdc Transmitter (Continued)Wiring Notes: 0-5 Vdc pigtail cable option1. Hookup: The 0-5 Vdc output style trans
HPT 100 SERIESWARRANTY POLICYAmetek warrants these products for a period of three years from the date of shipment ordate of registration if the card i
SECTION II____________________________________OUTDOOROnly certain versions of the HPT 100 are recommended for outdoor locations. Under theElectrical
pg. 2-6SECTION III OPERATIONPrinciple of OperationThe Model HPT 100, Ultra High Purity Pressure Transmitter series is a state of the artfamily of pres
SECTION IV CALIBRATIONField Adjustments:NOTE: Any change to the factory calibration will require the operator to re-check andrecord the new diagnosti
The elevated zero at atmospheric pressure for a 0.1-5.1 Vdc unit is:Elevated Zero = 0.1V + (Slope) x (abs. value of full vacuum. - abs. value of avail
Locate the supplied jumper plug and insert over the two terminal header pins above thepotentiometers. Check that the output is approximately 15 mA -
SECTION V SERVICEFACTORY SERVICEFactory or field service is available by contacting the Customer Service Department.Supply the following information:1
SECTION V SERVICEReplacement of electronic circuit boards:The HPT 100 should provide reliable operation over an extended period of time. If yoususpec
SECTION V SERVICESpare Parts/Accessories List:Ametek can supply you with needed parts to support your field service program.The following parts are cu
U.S. GAUGE DIVISIONPMT PRODUCTS820 PENNSYLVANIA BLVD. FEASTERVILLE PA 19053TEL: (215) 355-6900FAX: (215) 355-2937K796416 REV G (2/05/00)
CONTENTSWARRANTYcoverSeller’s Registration Card iiINTRODUCTIONiiiSafety SummarySECTION I- SPECIFICATIONSModel HPT 100 Series Transmitter ModelNumber S
WARRANTY REGISTRATION REPORTDISTRIBUTOR: DATE:LOCATION:CUSTOMER: CONTACT NAME:ADDRESS: PHONE:The units listed below have been delivered and the warran
_____________________________________________________INTRODUCTIONThe HPT 100 is a series of pressure transmitters specifically designed to meet the ul
SECTION I SPECIFICATIONS100-------AGENCYAPPROVAL1 = Intrinsic Safety/
DESCRIPTION:The HPT 100F is a flow-through style transmitterwhile the HPT 100S is a single-ended or deadlegstyle. Each style is available with a vari
PERFORMANCE SPECIFICATIONS:ACCURACY: ± 0.25% of FS includes linearity (BFSL), hysteresis andrepeatabilityRESPONSE: Time constant of less than 20 mill
SECTION I EMI/ RFI IMMUNITYAmetek UHP Transmitter CE MarkingThe Model HPT 100 4-20 mA and 0-5Vdc transmitters have been tested and declared asconformi
Comments to this Manuals