HP C110 User Manual

C100_110-160_180.FB -1 Tue Jul 16 06:36:50 1996Installing the C100/C110 to C160/C180 CPU UpgradeHP Part No. A4200-90017E0796Printed in USA

C100_110-160_180.FB 8 Tue Jul 16 06:36:50 19968Removing Memory ModulesRemoving Memory ModulesAfter removing the main tray from the system, you mus

C100_110-160_180.FB 9 Tue Jul 16 06:36:50 19969Removing Memory Modules2 To remove a memory module, push the ejector tabs on each side of the modul

C100_110-160_180.FB 10 Tue Jul 16 06:36:50 199610Removing Option BoardsRemoving Option BoardsNOTICE: Any option boards that are supported by the n

C100_110-160_180.FB 11 Tue Jul 16 06:36:50 199611Removing Option Boards2 Slide the EISA slider to the side to remove it, as shown in Figure 6.3 Re

C100_110-160_180.FB 12 Tue Jul 16 06:36:50 199612Installing Memory ModulesInstalling Memory ModulesInstall the memory modules in the C160/C180 CPU

C100_110-160_180.FB 13 Tue Jul 16 06:36:50 199613Installing Memory ModulesTable 1 Model C160/C180 Allowable Memory ConfigurationsConfig.No.Pair 0 Pa

C100_110-160_180.FB 14 Tue Jul 16 06:36:50 199614Installing Memory Modules25 32 32 32 32 32 32 32 32 32 32 32026 32 32 32 32 32 32 32 32 32 32 16

C100_110-160_180.FB 15 Tue Jul 16 06:36:50 199615Installing Memory Modules49 64 64 64 64 25650 64 64 64 64 16 16 28851 64 64 64 64 16 16 16 16 320

C100_110-160_180.FB 16 Tue Jul 16 06:36:50 199616Installing Memory Modules73 64 64 64 64 64 64 32 32 32 32 32 32 57674 64 64 64 64 64 64 64 64 512

C100_110-160_180.FB 17 Tue Jul 16 06:36:50 199617Installing Memory Modules2 To install a memory module, close the ejector tabs on each side of the

C100_110-160_180.FB 0 Tue Jul 16 06:36:50 1996 Hewlett-Packard Co. 1996Printing HistoryFirst Printing: July 1996UNIX is a registered trademark in

C100_110-160_180.FB 18 Tue Jul 16 06:36:50 199618Installing Option BoardsInstalling Option BoardsNOTICE: Any option boards that are supported by t

C100_110-160_180.FB 19 Tue Jul 16 06:36:50 199619Installing Option BoardsGraphics Configuration RestrictionsThe system supports only four graphics

C100_110-160_180.FB 20 Tue Jul 16 06:36:50 199620Installing Option BoardsOption Board InstallationIf you removed option boards from the C100/110 m

C100_110-160_180.FB 21 Tue Jul 16 06:36:50 199621Installing Option Boards2 Remove the screw from the EISA retainer, and remove the EISA retainer,

C100_110-160_180.FB 22 Tue Jul 16 06:36:50 199622Installing Option Boards4 In the desired option slot, turn the blank plate’s locking knob counter

C100_110-160_180.FB 23 Tue Jul 16 06:36:50 199623Installing Option Boards6 Slide the option board into the slot. Make sure that the hole in the bo

C100_110-160_180.FB 24 Tue Jul 16 06:36:50 199624Installing Option Boards8 Replace the EISA retainer and its screw, as shown in Figure 13.9 Replac

C100_110-160_180.FB 25 Tue Jul 16 06:36:50 199625Installing Option Boards10 Rotate the fan back into place and firmly push it into the rear panel

C100_110-160_180.FB 26 Tue Jul 16 06:36:50 199626Installing the New Main Tray AssemblyInstalling the New Main Tray AssemblyInstall the new C160/C1

C100_110-160_180.FB 27 Tue Jul 16 06:36:50 199627Installing the New Main Tray Assembly5 Remove any external SCSI terminators from the rear of the

C100_110-160_180.FB 1 Tue Jul 16 06:36:50 19961Upgrading your Model C100/110 to a Model C160 or C180Upgrading your Model C100/110 to a Model C160

C100_110-160_180.FB 28 Tue Jul 16 06:36:50 199628Installing the New Main Tray Assembly7 Replace the system unit in the floor stand, as shown in Fi

C100_110-160_180.FB 29 Tue Jul 16 06:36:50 199629Installing the New Main Tray Assembly8 Reconnect the power cables and any other cables that you d

C100_110-160_180.FB 30 Tue Jul 16 06:36:50 199630Installing the New Main Tray Assembly11 The system cycles through all of the available monitor ty

C100_110-160_180.FB 31 Tue Jul 16 06:36:50 199631Installing the New Main Tray Assembly15 At the prompt, enter the following command to enter the c

C100_110-160_180.FB 32 Tue Jul 16 06:36:50 199632Installing the New Main Tray Assembly

C100_110-160_180.FB 2 Tue Jul 16 06:36:50 19962Preparing Your WorkstationPreparing Your WorkstationBefore starting the upgrade, use the following

C100_110-160_180.FB 3 Tue Jul 16 06:36:50 19963Preparing Your Workstation4 Next, you need to run the upgrade utility program to automatically conv

C100_110-160_180.FB 4 Tue Jul 16 06:36:50 19964Preparing Your Workstation5 If your system has an A4070B HCRX-8Z or an A4071B with the A4272A acce

C100_110-160_180.FB 5 Tue Jul 16 06:36:50 19965Preparing Your Workstation12 Unplug the power cord of the system unit, the monitor, and any periphe

C100_110-160_180.FB 6 Tue Jul 16 06:36:50 19966Preparing Your Workstation14 Remove the floor stand from the system unit, as shown in Figure 1.Figu

C100_110-160_180.FB 7 Tue Jul 16 06:36:50 19967Removing the Main Tray AssemblyRemoving the Main Tray AssemblyOnce you have prepared the workstatio