Hardware Reference GuideHP EliteDesk 800 G3 SFF Business PC
Serial number locationEach computer has a unique serial number and a product ID number that are located on the exterior of the computer. Keep these nu
2 Hardware upgradesServiceability featuresThe computer includes features that make it easy to upgrade and service. A Torx T15 or at-bladed screwdrive
Removing the computer access panelTo access internal components, you must remove the access panel.1. Remove/disengage any security devices that prohib
Replacing the computer access panelBe sure that the access panel release lever is locked into place, and then place the access panel on the computer (
Removing the front bezel1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compact dis
Removing a slim optical drive bezel blankOn some models, a bezel blank covers the slim optical drive bay. Remove the bezel blank before installing an
Removing and installing the optional front bezel dust lterSome models are equipped with an optional front bezel dust lter. You must periodically cle
5. To replace the dust lter, press the lter rmly onto the front bezel at the tab locations shown below.6. Reconnect the power cord and any external
Changing from desktop to tower orientationThe Small Form Factor computer can be used in a tower orientation with an optional tower stand that can be p
System board connectionsRefer to the following illustration and table to identify the system board connectors for your model.Item System board connect
© Copyright 2016, 2018 HP Development Company, L.P.Windows is either a registered trademark or trademark of Microsoft Corporation in the United States
Upgrading system memoryThe computer comes with double data rate 4 synchronous dynamic random access memory (DDR4-SDRAM) dual inline memory modules (DI
DIMM and one 1 GB DIMM, and Channel B should be populated with the other two 1 GB DIMMs. With this conguration, 4 GB will run as dual-channel and 1 G
7. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Press the module down into the socket, ensurin
Removing or installing an expansion cardThe computer has two PCI Express x1 expansion sockets, one PCI Express x16 expansion socket, and one PCI Expre
a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slot cover on the back of the chassis. Pull the slot c
c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card (1) and carefully rock th
13. Rotate the slot cover retention latch back in place to secure the expansion card.14. Connect external cables to the installed card, if needed. Con
Drive positionsDrive positions1 3.5-inch secondary hard drive bay2 3.5-inch primary hard drive bay3 2.5-inch hard drive bay4 9.5 mm slim optical drive
Removing a 9.5 mm slim optical drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as
8. Push the green release latch on the right rear side of the drive toward the center of the drive (1), and then slide the drive forward and out of th
About This BookThis guide provides basic information for upgrading the HP EliteDesk Business PC.WARNING! Indicates a hazardous situation that, if not
Installing a 9.5 mm slim optical drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such
9. Slide the optical drive through the front bezel all the way into the bay (1) so that the latch on the rear of the drive locks into place (2).10. Co
Removing a 3.5-inch hard driveNOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer
8. Pull the release lever next to the rear of the hard drive outward (1). While pulling the release lever out, lift the rear of the drive up (2), and
Installing a 3.5-inch hard driveNOTE: There are two 3.5-inch hard drive bays. The procedure for installing a 3.5-inch hard drive is the same for each
– Secure the drive to the bay adapter bracket by installing four black M3 adapter bracket screws through the underside of the bracket and into the dri
– Install four 6-32 silver-and-blue mounting screws in the adapter bracket (two on each side of the bracket).8. Align the mounting screws on the front
9. Connect the power cable (1) and data cable (2) to the rear of the hard drive.NOTE: If the 3.5-inch hard drive is the primary drive, connect the oth
Removing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as compa
9. Disconnect the power cable (1) and data cable (2) from the rear of the hard drive.10. Pull the release lever at the rear of the drive outward (1).
iv About This Book
Installing a 2.5-inch hard drive1. Remove/disengage any security devices that prohibit opening the computer.2. Remove all removable media, such as com
9. Rotate the drive cage to its upright position.10. Align the mounting screws on the drive with the J-slots on the sides of the drive bay. Press the
11. Connect the power cable (1) and data cable (2) to the rear of the hard drive.NOTE: If the 2.5-inch hard drive is the primary drive, connect the ot
Removing and installing an M.2 SSD storage cardNOTE: The computer supports 2230 and 2280 M.2 SSD cards.1. Remove/disengage any security devices that p
9. To remove an M.2 SSD card, remove the screw that secures the card (1), lift the end of the card up (2), and then slide the card out of the system b
11. Rotate the drive cage back down to its normal position.IMPORTANT: Be careful not to pinch any cables or wires when rotating the drive cage down.12
Installing a security lockThe security locks displayed below and on the following pages can be used to secure the computer.Cable lockPadlock40 Chapter
HP Business PC Security Lock V2The HP PC Security Lock V2 is designed to secure all of the devices at your workstation.1. Attach the security cable fa
3. Slide the security cable through the security cable fastener.4. Pull the two scissor hands of the monitor lock apart and insert the lock into the s
5. Slide the security cable through the security guide installed on the monitor.6. Attach the accessory cable fastener to a desktop using the appropri
Table of contents1 Product features ...
7. Slide the security cable through the holes in the accessory cable fastener.8. Screw the lock to the chassis using the screw provided.44 Chapter 2
9. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock. Use the key provided to disengage the lo
A Battery replacementThe battery that comes with the computer provides power to the real-time clock. When replacing the battery, use a battery equival
b. Slide the replacement battery into position, positive side up. The battery holder automatically secures the battery in the proper position.Type 2a.
b. Insert the new battery and position the clip back into place.NOTE: After the battery has been replaced, use the following steps to complete this pr
B Electrostatic dischargeA discharge of static electricity from a nger or other conductor may damage system boards or other static-sensitive devices.
C Computer operating guidelines, routine care and shipping preparationComputer operating guidelines and routine careFollow these guidelines to properl
Optical drive precautionsBe sure to observe the following guidelines while operating or cleaning the optical drive.Operation● Do not move the drive du
D AccessibilityHP designs, produces, and markets products and services that can be used by everyone, including people with disabilities, either on a s
IndexAaccess panelremoval 6replacement 7accessibility 52Bbattery replacement 46Ccomputer operating guidelines 50Ddrivescable connections 21installatio
Appendix B Electrostatic discharge ...
1 Product featuresStandard conguration featuresFeatures may vary depending on the model. For support assistance and to learn more about the hardware
Front panel componentsDrive conguration may vary by model. Some models have a bezel blank covering the slim optical drive bay.Front panel components1
Rear panel componentsRear panel components1 Audio-in jack 6 DisplayPort monitor connectors (2)2 Serial port (optional) 7 Optional port3 RJ-45 (netwo
Comments to this Manuals