Hp Command View EVA Software User Manual Page 104
- Page / 113
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
A HP array event code formats and descriptions
This appendix describes how the hexadecimal number for the event code is formed.
Event code format
Controller and controller termination event codes appear as 32–bit hexadecimal numbers (for
example, 060f4013). The bits in the event code differ slightly for each controller event type. The
bits of a controller event have the following format:
Table 9 HP array controller event code bits
7........................115........823.........1631............24
Event information packet typeCorrective action codeEvent numberSoftware component ID
The bits of a controller termination event have the following format:
Table 10 HP array controller termination event code bits
4........06........5.....7......15.......823.......1631.........24
Parameter countDump/restart
control code
Coupled crash
control code
Corrective action
code
Event numberSoftware
component ID
The following table provides the interpretation of each bit.
Table 11 HP array event code bit interpretation
InterpretationBit
The software component ID (SCID or SCWID) identifies the software component that generated the event.
The ID ranges from 0x00 to 0xFF.
24:31
The event number is unique for each software component and ranges from 0x00 to 0xFF. Each event code
is uniquely identifiable by the combination of the SCID and the event number in bits 16:23.
16:23
The corrective action code is in the range 0x00 to 0xFF.8:15
(Controller events only) The event information packet type contains a reason for the event and a template
that defines the meaning of the data in the packet. It is in the range 0x00 to 0x2F.
0:7
(Controller termination events only) The coupled crash control code specifies whether both controllers are
terminating operation.
7
(Controller termination events only) The dump/restart control code specifies whether a crash dump is
occurring as part of the termination and whether the controllers will restart following termination.
5:6
The termination parameter count specifies the number of entries in the Termination Parameters array that
are valid for this termination. If the parameter count is greater than zero, the termination code description
in the parse file will describe the meaning of each parameter.
0:4
Event code types and descriptions
This section lists the event code types and descriptions.
Software component IDs
Table 12 HP array software component IDs
DescriptionID
Executive Services1
Cache Management Component2
Storage System State Services3
104 HP array event code formats and descriptions
- User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- 1 Overview 7
- 8 Overview 8
- 4. Browsing computer1. LAN 10
- 5. Hosts2. SAN 10
- 3. HP EVA4400 storage systems 10
- 10 Overview 10
- User interface 11
- Storage systems point of view 12
- Settings point of view 13
- 14 Overview 14
- Internet Protocol support 15
- Password formats 16
- Considerations 17
- License types 20
- Instant-on licenses 20
- Permanent licenses 20
- Data migration licenses 21
- FCIP licenses 21
- Obtaining license keys 22
- Retrieving licenses 23
- Entering license keys 23
- Importing licenses 24
- 4 Provisioning storage 26
- Disk types 27
- Disk group types 27
- General guidelines 27
- Disk group capacity 28
- Redundancy (Vraid) levels 29
- Virtual disks 30
- 32 Provisioning storage 32
- Presentation 33
- Online virtual disk migration 33
- Mirrorclone migration 34
- Thin provisioning 34
- Online Help 35
- 5 Replicating storage 36
- Snapshots 37
- Mirrorclones 38
- Containers 40
- Optimizing snap creation 41
- 42 Replicating storage 42
- DR groups 43
- Creating DR groups 44
- Initializing storage systems 46
- User-initiated service mode 47
- Starting the storage system 48
- Figure 10 HSV450 rear view 49
- Resynchronizing controllers 50
- Hardware 50
- Verifying hardware status 51
- Remote service test 51
- Configuring iSCSI devices 53
- Events overview 55
- Viewing events 56
- Viewing events 57 57
- Configuring host notification 58
- Filtering events by severity 59
- Retrieving the parse file 60
- Sending the event file 62
- Creating page footer messages 63
- Setting audit logging options 64
- Configuring SNMP credentials 66
- Optimizing performance 67
- Using the right-click menu 67
- Failed transceiver 70
- Failed I/O module 70
- Failed blower power supply 70
- Version numbers differ 72
- Performance Data Collector 74
- Events and logs 79
- Logging configuration file 79
- Configuration recommendations 80
- SSL protocol 81
- Prohibited commands 81
- Backward compatibility 81
- Using friendly names 82
- Using friendly names 83 83
- Using short names 84
- Viewing storage systems 85
- Specifying the output 85
- Filtering data 86
- Commands 87
- Command modifiers 89
- Data filtering 92
- Objects and counters 93
- HP EVA virtual disk 94
- HP EVA virtual disk group 95
- HP EVA host connection 96
- HP EVA host port statistics 96
- HP EVA physical disk 96
- HP EVA physical disk group 97
- HP EVA DR tunnels 97
- HP EVA DR Group Information 98
- HP EVA Xcopy Metrics 99
- HP EVA WSame Metrics 99
- HP EVA Unmap Metrics 100
- Contacting HP 101
- Related information 101
- Typographical conventions 102
- 12 Documentation feedback 103
- Event code format 104
- Corrective action codes 105
- Coupled crash control codes 106
- Dump/restart control codes 107
- Glossary 108
- 110 Glossary 110
- 112 Index 112
Related products and manuals for Storage Hp Command View EVA Software
Storage Hp XP7 Storage User Manual
(250 pages)
(250 pages)
(58 pages)
(60 pages)© 2020, manymanuals.com. All rights reserved. | 0.938 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals