HP xw460c User Manual

HP BIOS Serial Console User Guide July 2004 (First Edition) Part Number 372432-001

10 HP BIOS Serial Console User Guide IMPORTANT: Settings take effect on the next RBSU-prompted reboot, but you must disconnect and then reconnect

HP BIOS Serial Console/EMS Support Settings and Configuration 11 For detailed information about iLO configurations, refer to the HP Integrated Lig

12 HP BIOS Serial Console User Guide Press the Enter key while Terminal Emulation Mode is selected to display the emulation mode options. Select th

HP BIOS Serial Console/EMS Support Settings and Configuration 13 Some new servers, which use CLI and are configured using BIOS Serial Console, wil

14 HP BIOS Serial Console User Guide Baud Rate Press the Enter key while BIOS Serial Console Baud Rate is selected to display the baud rate. The de

HP BIOS Serial Console/EMS Support Settings and Configuration 15 IMPORTANT: Enabling port settings enables console redirection only at POST comma

16 HP BIOS Serial Console User Guide NOTE: You must use escape sequences if the emulation program does not support function keys, but they also wo

HP BIOS Serial Console/EMS Support Settings and Configuration 17 Keyboard Entry Defined As <ESC>R<ESC>r<ESC>R System Reset

18 HP BIOS Serial Console User Guide When Enable Local is selected, the OS redirects through the local serial port. When Enable Remote is selected,

HP BIOS Serial Console/EMS Support Settings and Configuration 19 Microsoft® enables EMS support in the OS, but EMS support also requires ROM suppo

© Copyright 2004 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Intel is a

20 HP BIOS Serial Console User Guide Linux Red Hat 7 ATA Driver Settings By default, Linux Red Hat 7.1 OS uses only the ATA driver in PIO mode for

Terminal Emulation Programs 21 Microsoft HyperTerminal Setup Because Microsoft® HyperTerminal is a widely used terminal emulation program, example

22 HP BIOS Serial Console User Guide 3. On the Connect To tab, click Configure to display the Port Settings tab. NOTE: If using a notebook compu

Terminal Emulation Programs 23 4. Select Port Settings. Then click OK to return to the Properties screen. 5. On the Properties screen, click the

24 HP BIOS Serial Console User Guide 6. If using ANSI emulation, click Terminal Setup and select ANSI (if using VT100 emulation, refer to step 9).

Terminal Emulation Programs 25 7. Select Terminal Settings. 8. Click OK to return to the Settings tab, and click OK again to complete the HyperTe

26 HP BIOS Serial Console User Guide 9. If using VT100 emulation, click Terminal Setup and select VT100. IMPORTANT: If using VT100 emulation, th

Terminal Emulation Programs 27 10. Select Terminal Settings. Click OK to return to the Settings tab. 11. On the Settings tab, click ASCII Setup.

28 HP BIOS Serial Console User Guide 12. Deselect Wrap lines that exceed terminal width. Click OK to return to the Settings tab. Then click OK to c

29 Acronyms and Abbreviations ASR Automatic Server Recovery CLI Command Line Interface ConRep Configuration Replication Utility ECC error chec

3 Contents Console Redirection Overview 5 Purpose...

30 HP BIOS Serial Console User Guide IPL initial program load IRQ interrupt request MPS multi-processor specification NIC network interface cont

Acronyms and Abbreviations 31 RILOE Remote Insight Lights-Out Edition RILOE II Remote Insight Lights-Out Edition II

33 Index A ASR (Automatic Server Recovery) 29 ATA driver settings 20 B baud rate 14 BIOS Serial Console 5, 6 C COM port 6 commands 15

5 Console Redirection Overview In This Section Purpose ...

6 HP BIOS Serial Console User Guide BIOS Serial Console Overview BIOS Serial Console can be enabled in RBSU. By default, BIOS Serial Console is dis

Console Redirection Overview 7 • RBSU and BIOS Serial Console Configuration (on page 9) − Terminal Emulation Support (on page 11) − Baud Rate (on

9 HP BIOS Serial Console/EMS Support Settings and Configuration In This Section RBSU and BIOS Serial Console Configuration ......