HP J3245A User Manual Page 15
- Page / 213
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-1
Installation
1
Installation
Installation Summary
This chapter describes the installation procedures for the HP J3245A
AdvanceStack Switch 800T (hereafter referred to as the Switch 800T).
The following is a summary of those procedures:
1. Site Preparation. Ensure that the cabling infrastructure meets the
network specifications for your intended use of the Switch 800T.
• For 100Base-TX transceivers used in the Switch 800T, use category 5,
four-pair, 100 ohm UTP (unshielded twisted-pair) cables. Cable
lengths can be up to 100 meters. For a connection to an end node, use
straight-through cable. For a connection to a hub or a switch, use a
crossover cable.
• For 100Base-FX transceivers used in the Switch 800T, use fiber
optical cables that:
– Are fitted with type SC connectors
– Conform to ISO/IEC 793-2 type B1 and ITU-T G.652 standards
Caution Ensure that the power source circuits are adequate and properly
grounded. That is, ensure that any Switch 800T installation , together with
any other devices, does not overload the power circuits, wiring, and over-
current protection. To determine the possibility of overloading the supply
circuits, add together the ampere ratings from the nameplates of all
devices installed on the same circuits and compare the total with the
rating limits for the supply circuits. For additional information, refer to
appendix B, “Specifications”.
SEDONA.BK : sed_1.fm5 Page 1 Thursday, February 27, 1997 10:11 AM
- HP AdvanceStack Switch 800T 1
- HP Customer Support Services 3
- Perforate 4
- Documentation 7
- Contents 9
- Console 10
- 8: File Transfers 11
- 9: Troubleshooting 11
- 7: Advanced Concepts 11
- A: Cables and Connectors 12
- B: Specifications 12
- D: Switch Reference 12
- E: BOOTP Operation 13
- F: MAC Address Management 13
- Installation 15
- Installation Summary 16
- Verify the Switch Hardware 20
- 3. Mount the Switch 22
- Rack or Cabinet Mounting 23
- Mounting the Switch on a Wall 28
- Table Mounting 29
- 4. Connect a Power Supply 30
- Power Supply (RPS): 31
- Cable Management 34
- Where To Go from Here 39
- Using the Console Interface 41
- Main Menu Features 44
- Using Password Security 47
- Rebooting the Switch 50
- Resetting the Switch 52
- Configuring the Switch 53
- Configurable Features 55
- System Features 57
- Port Features 58
- IPX Service Features 59
- Virtual LAN (VLAN) Features 63
- Traffic Control 64
- SNMP Communities Features 65
- Trap Receivers Features 67
- Serial Link Features 68
- Console Features 69
- Spanning Tree Features 73
- Switching 75
- Status and Counters Menu 78
- Switch Information 79
- Port Status 80
- Port Counters 81
- Address Table 83
- Port Address Table 84
- Monitoring and Analyzing 85
- Switch Operation from the 85
- IP Multicast (IGMP) Status 88
- Event Log 91
- Log Status Line 92
- SNMP Management 95
- SNMP Configuration Process 97
- Using the Advanced Commands 100
- Overview 100
- Commands 102
- Using the Advanced 103
- Advanced Concepts 107
- Spanning Tree Protocol (STP) 108
- Port Trunking 111
- Filters and Security 114
- Virtual LANs (VLANs) 120
- Overview of Using VLANs 122
- How To Configure a VLAN 123
- VLAN Restrictions 127
- Environments 128
- IP Multicast (IGMP) 129
- How To Configure IGMP 132
- How ABC Operates 136
- How To Configure ABC 138
- File Transfers 145
- Switch-to-Switch Download 149
- Troubleshooting 155
- Diagnosing with the LEDs 156
- LED Error Indications 157
- Installation Problems 159
- Cabling Problems 160
- Unusual Network Activity 161
- Diagnostic Tests 161
- Customer Support Services 162
- Cables and Connectors 163
- Recommended Cables 164
- MDI-X Hub Port 166
- RS-232-C “Null Modem” Cable 169
- RS-232 Modem Cable 170
- Specifications 171
- Connectors 172
- Electromagnetic 172
- Sample Console Configurations 173
- Procomm Plus V2.01 174
- Other Terminal Emulators 175
- Switch Reference 177
- Port Status LEDs 179
- Console RS-232 Port 182
- Back of the Switch 183
- BOOTP Operation 185
- Bootp Database Record Entries 186
- Configuring Bootp 187
- MAC Address Management 189
- Switch (Default) MAC Address 190
- VLAN MAC Addresses 191
- Operation) 192
- Safety Information 193
- Symboles de sécurité 194
- Hinweise zur Sicherheit 195
- Regulatory Statements 199
- European Community 200
- DOC Statement (Canada) 200
- Declaration of Conformity 201
- Safety-10 202
- Safety and Regulatory 202
- Statements 202
- Numerics 203
- Index - 2 204
- Index - 3 205
- Index - 4 206
- Index - 5 207
- Index - 6 208
- Index - 7 209
- Index - 8 210
- Index - 9 211
- *J3245-90001* 213
Related products and manuals for Network switches HP J3245A
Network switches HP 1700-24 User Manual
(56 pages)
(56 pages)
Network switches HP 2520G-POE User Manual
(101 pages)
(101 pages)
Network switches HP GbE2c User Manual
(175 pages)
(175 pages)
Network switches HP B-Series User Manual
(13 pages)
(13 pages)
Network switches HP J3178A User Manual
(112 pages)
(112 pages)
Network switches HP 212M User Manual
(166 pages)
(166 pages)
Network switches HP 8212zl User Manual
(138 pages)
(138 pages)
Network switches HP 10BASE-T User's Guide
(44 pages)
(44 pages)
Network switches HP SN6000 User Manual
(90 pages)
(90 pages)
Network switches HP 2524 User Manual
(66 pages)
(66 pages)
© 2020, manymanuals.com. All rights reserved. | 0.464 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals